English Deutsch Français USB-AUDIO INTERFACE USB-AUDIO INTERFACE Yamaha Web Site (English only) www.yamahasynth.com Yamaha Manual Library http://www2.yamaha.co.jp/manual/english/ This document is printed on recycled chlorine free (ECF) paper with soy ink. Auf Recycling-Umweltpapier gedruckt. Ce document a été imprimé sur du papier recyclé non blanchi au chlore. M.D.G.
SPECIAL MESSAGE SECTION This product utilizes an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Do not open • Do not open the instrument or attempt to disassemble the internal parts or modify them in any way.
• Do not operate the instrument for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. English Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
Welcome to the UW10 Thank you for choosing the Yamaha UW10 USB-Audio Interface. The UW10 is a USB interface that enables simultaneous transfer of audio data. Connect the UW10 to a computer that has a USB connector and enjoy the powerful features of digital audio. Please read this Owner’s Manual thoroughly to make the best use of the UW10. After you read this manual, please keep it in a safe place for future reference. English Table of contents UW10 Features.................................................
UW10 Features ● Digital and analog interface The UW10 functions as an interface that enables you to digitally record MDs and cassette tapes to a computer, or create music using an audio/MIDI sequencer and MIDI tone generators (MOTIF-RACK etc.). The analog inputs on the UW10 convert incoming analog signals into digital. This prevents audio deterioration due to computer noise and enables you to perform clean, clear sound recordings.
Notes on musical copyrights The UW10 supports SCMS (Serial Copy Management System) to protect copyrights associated with music software. When you copy data from CDs, or other music media purchased from stores, to your own media (such as MDs) using a digital connection, information regarding the digital recording generation is also recorded. If you route the recorded data to a DIGITAL IN jack, you will be unable to record the data on a computer.
Package Contents The UW10 package contains the following items. Check the contents for missing items. • UW10 main unit • CD-ROM • USB cable (approx. 2 meters) • Owner’s Manual (this book) English About the included software The included CD-ROM contains the following software programs. The “English” folder on the included CD-ROM contains the following software programs. NOTE Each program’s operating environment may be different from the UW10’s operating environment (page 10).
NOTE Windows 2000/XP Users: If you hear sound skips from the S-YXG50 on the Windows 2000/XP platform, you may be able to resolve the problem by following the steps below: 1. From the “Start” menu, select [Programs | YAMAHA XG SoftSynthesizer S-YXG50 | S-YXG50 Settings] to display the “Settings” window. 2. Click the “Information” tab. If the window indicates “Ver.4.01.xx Legacy” (xx is a version number) for the S-YXG50 version, proceed to Step 3. 3.
ASIO driver This driver software is required if you wish to use applications that support ASIO. Refer to the “ReadMe.html” in “English” folder in the “ASIOdrv_” folder for information on how to install the driver. NOTE TWEplus does not support ASIO.
CAUTION With some application programs, input audio signals may be output unmodified. In this case, do not set the SOURCE SELECT switch to “TRACK DOWN.” Otherwise, audio signals may oscillate, causing hearing loss or damage to the playback device. 3 USB connector Connect this connector to a computer’s USB connector using a USB cable. You do not have to turn off the power to the computer when you connect this connector.
Signal Flow Depending on the SOURCE SELECT switch setting, the audio signal flow varies as follows: When the switch is set to “INPUT”: Audio signals input at the INPUT jacks can be recorded to a computer via the USB connection. USB DIGITAL IN INPUT L OUTPUT R L R OUT English IN OUT Headphone VOLUME When the switch is set to “DIGITAL”: Audio signals input at the DIGITAL IN jack can be recorded to a computer via the USB connection.
Connections Combining the UW10 with other devices allows for versatile applications as follows: Using the UW10 along with a tone generator, such as MOTIF-RACK, enables highquality recording. Connect the UW10, the MOTIF-RACK and a computer using USB cables. Connect the MOTIF-RACK to the UW10’s DIGITAL IN jack, and set the UW10’s SOURCE SELECT switch to “DIGITAL.
● Music production system using a guitar or microphone via analog connections Analog audio signals input from a guitar or microphone are converted to digital for recording. Patch the analog input from the guitar or microphone to the UW10’s INPUT jacks via an effects unit or other equivalent device. In this case, set the UW10’s SOURCE SELECT switch to “INPUT,” and connect powered speakers or headphones to the UW10.
computer cassette tape deck USB turntable INPUT OUT DIGITAL L R INPUT L R OUTPUT AV amplifier and mixer DIGITAL IN speakers SOURCE SELECT DIGITAL INPUT TRACK DOWN USB-AUDIO INTERFACE English IN OUTPUT DIGITAL OUT MD recorder UW10 ● Track down on the computer You can track down multiple wave files or SoftSynthesizer audio signals into a single wave file, which can then be converted to an MP3 file using the included TWEplus wave editor.
Installing the driver Before you can use the UW10, you need to install the driver on the computer. The USB audio driver enables you to transfer audio signals between an audio application on the computer and the UW10 via a USB cable. computer audio application USB cable IN OUT English DIGITAL L R INPUT L R OUTPUT SOURCE SELECT DIGITAL INPUT TRACK DOWN driver USB-AUDIO INTERFACE audio data UW10 NOTE The UW10 does not work with a USB hub that is powered by the USB bus power supply.
● Installing the driver on a Windows 98/98SE system 1. Start the computer. English 2. Use the included USB cable to connect the UW10 to the computer’s USB connector. The UW10 is powered on and the system automatically displays the “Add New Hardware Wizard.” 3. Click [Next]. The system displays a screen that enables you to select a search method.
English 4. Check the radio button to the left of “Search for the best driver for your device. (Recommended).” Click [Next]. The system displays a screen that enables you to select a location in which to install the driver. 5. Uncheck all items, then click [Next]. 6. When the system detects the driver and is ready for installation, it displays the following screen. Make sure that the “USB Composite Device” is listed, then click [Next]. The system starts the installation.
7. When the installation is complete, the following screen appears. Click [Finish]. Some computers may take about ten seconds to display this screen after installation is complete. English NOTE 8. After a few seconds, the “Add New Hardware Wizard” is displayed again. Install “USB Audio Device” in the same manner as steps 3-7 described above. The driver has been installed.
● Installing the driver on a Windows 2000/XP system 1. Start the computer. 2. Use the included USB cable to connect the UW10 to the computer’s USB connector. The system displays the message “Found New Hardware” and automatically detects and installs the driver. The window closes and the driver is installed. ● Installing the driver on a Windows Me system English 1. Start the computer. 2. Use the included USB cable to connect the UW10 to the computer’s USB connector.