User Manual
Table Of Contents
- Cover
- Contents
- Differences Between the DTX-PRO and the DTX-PROX
- Links from the Owner’s Manuals
- How the Triggers Generate Sounds
- The Relationship Between Trigger Input Jacks, Trigger Inputs, and Trigger Input Sources
- Trigger Input Jack Input Mode
- Sounds that are played by trigger (Inst and Voice)
- Voices and Layers
- User Voices
- Importing to User Voices
- Changing the way a user voice is played (one-shot or Loop)
- Editing and auditioning user voices
- Selecting the Trigger Input or Trigger Input Source
- Effect Processor Design
- PRO Series Modules Internal Memory
- MENU Button
- KIT Mode
- CLICK Mode
- RECORDER Mode
- Practicing with the Training Feature
- Fader Select FX
- Fader Select CUSTM
- LIVE SET Mode
- Settings for live performances
- Connecting a Computer
- Troubleshooting
- Reference
137
DTX-PRO DTX-PROX Reference Manual
Troubleshooting
Symptom Possible cause
Solution
DTX-PRO DTX-PROX
No sound
Out of balance
No sound The cable is not prop-
erly connected
• Ensure that the PRO series module is properly connected to
headphones or an external audio system, such as an amplifier
and/or speakers.
• Ensure that the cables you are using are in good condition.
Pad settings have not
been properly config-
ured
Turn the “PadFunction” setting in MENU/Utility/Pad “off.”
Trigger settings are
improper
• Check the “Pad Type” parameter from MENU/Trigger/Pad Type
or TRIGGER/SETTING/Pad Type.
• Check the “Velocity Curve” parameter from MENU/Trigger/
Curve or TRIGGER/SETTING/Curve, and the “Gain” parameter
from MENU/Trigger/Pad Type or TRIGGER/SETTING/Pad Type.
• Ensure that the “Minimum Level” parameter from MENU/Trig-
ger/Pad Type or TRIGGER/SETTING/Pad Type has not been set
too high, as this can prevent sound from being output.
• Check the settings in MENU/Trigger/Input Mode or TRIGGER/
SETTING/Input Mode.
Filter and decay set-
tings have not been
properly configured
• If using filters, re-adjust your VoiceFilter settings as they often
prevent sound from being output.
• Check the VoiceFilter and VoiceDecay settings in MENU/Kit
Edit/Voice.
MIDI settings have not
been properly config-
ured
• Ensure that the “MessageType” parameter from MENU/Kit Edit/
Kit Modifier/Voice is set to “note.”
• When the “MessageType” parameter from MENU/Kit Edit/Kit
Modifier/Voice is set to “note,” the sound will not play if the
“Voice Number” parameter from MENU/Kit Edit/Kit Modifier/
Voice is set to “no assign.”
• Ensure that the “VelLo” parameter from MENU/Kit Edit/Kit Mod-
ifier/Voice/MessageType is not set t
oo high. Pads will pr
oduce
sound only when struck harder than the value set here.
• Ensure that the “Trg Ve l” parameter from MENU/Kit Edit/Kit Mod-
ifier/Voice/MessageType is not set too low. Low trigger velocities
result in low output volumes.
• Ensure that the “MIDI LocalCtrl” parameter from MENU/Utility/
General is set to “on.”
The volume or level set-
tings are improper
The headphone volume
is not turned up
The metronome volume
is not turned up
Check the following:
• Volume controllers on amplifiers and/or speakers connected to
the PRO series module.
• MENU/Kit Edit/Volume
• The trigger output level of any pads with a dial allowing this to be
adjusted.
• The [MASTER VOLUME]
knob on the DTX-PRO front
panel.
• The sliders on the MIXER
screen.
• Volume for the metronome
(Click). ([CLICK VOLUME]
knob)
• Sliders ([OUTPUT] and
[PHONES]) on the DTX-
PROX top panel.
• LED rotary faders
• Volume for the metronome
(Click) ([CLICK] slider).