User Manual
Table Of Contents
- Cover
- Contents
- Links from the Owner’s Manual
- How the Triggers Generate Sounds
- The Relationship Between Trigger Input Jacks, Trigger Inputs, and Trigger Input Sources
- Trigger Input Jack Input Mode
- Sounds that are played by trigger (Inst and Voice)
- Voices and Layers
- User Voices
- Importing to User Voices
- Changing the way a user voice is played (one-shot or Loop)
- Editing and auditioning user voices
- Selecting the Trigger Input or Trigger Input Source
- Effect Processor Design
- DTX-PRO Internal Memory
- MENU Button
- KIT Mode
- CLICK Mode
- RECORDER Mode
- TRAINING Mode
- Connecting a Computer
- Troubleshooting
- Reference
Troubleshooting
104
DTX-PRO Reference Manual
Effects cannot be
applied
• Ensure that the [EFFECT] knob is not turned down to minimum.
• Ensure that the effect type is not set to “THRU” or “NO EFFECT.”
• Ensure that the InstSend value is high enough for Effect 1 or Effect
2.
The wave tempo
does not change
Wave tempo cannot be changed. It will always play at the original
tempo of the imported file regardless of kit tempo and other settings.
Pad controller does
not work
Pad controllers are not supported.
By pressing the
[REC] button, only
one song can be
recorded. The previ-
ous recording is over-
written
Only one song can be recorded to the DTX-PRO.
My training scores
are strange
Crosstalk is occurring See the section on “Crosstalk.”
Settings The DTX-PRO does
not store its settings
The DTX-PRO automatically stores its system settings whenever you
turn it off using the [ ] (Standby/On) button.
• Do not turn off the DTX-PRO by unplugging the AC adaptor. This
will prevent it from storing the system settings.
• User settings for kits, click sets, and triggers must be stored manu-
ally.
Data cannot be saved
on a USB flash drive
USB 1.1 compatible flash drives cannot be used on the DTX-PRO.
• Ensure that the USB flash drive has been formatted using the DTX-
PRO.
• Ensure that the USB flash drive has not been write-protected.
• Ensure that there is sufficient free space on the USB flash drive to
save the data. Check the free space from “Memory Info” in MENU/
File/.
Cannot load audio
files from a USB flash
drive
Cannot load stan-
dard MIDI files from a
USB flash drive
USB 1.1 compatible flash drives cannot be used on the DTX-PRO.
• Ensure that there is sufficient free space on the DTX-PRO.
• Format the USB flash drive with the DTX-PRO.
• Ensure that the file to be read is located within the root directory of
the USB flash drive (that is, not within any folder).
Cannot send data to
or from the smart
device
Check the connection. For more information, refer to the iPhone/iPad
Connection Manual or Smart Device Connection Manual for
Android™.
Wave does not play The wave has been
deleted
For a user voice with an audio file imported into it, the sound no lon-
ger plays if the wave has been deleted.
Connected external
device does not pro-
duce sound
The device is not con-
nected properly
The MIDI channels do
not match
A function has been
assigned to the pad
The pad volume is low
• Ensure that the MIDI cable has been correctly connected.
• Ensure that the MIDI channels match. For more information on MIDI
settings, see page 31.
• When using a USB MIDI connection, ensure that USB cables have
been correctly connected.
• Pads that have been assigned a function will not play sound even
when struck. Set the “Pad Function” in MENU/Utility/Pad to “off.”
• Ensure that the “MessageType” parameter from MENU/Kit Edit/
Voice is set to “note.” Sounds will not be produced if this is not set to
“note.”
• Ensure that the “VelLo” parameter from MENU/Kit Edit/Voice/Mes-
sageType is not set too high. Pads will produce sound only when
struck harder than the value set here.
• Ensure that the “Minimum Level” parameter from MENU/Trigger/Pad
Type has not been set too high, as this can prevent sound from
being output.
Symptom Possible cause Solution