User Manual

MOTIF XF Data List
102
Effect Parameter List
Category — TEC
[1] RING MODULATOR
[2] DYNAMIC RING MODULATOR
[3] DYNAMIC FILTER
[4] AUTO SYNTH
[5] ISOLATOR
[6] SLICE
[7] TECH MODULATION
Category — MISC
[1] VCM EQ 501
No. Parameter Range Value Table No.
1 OSC Frequency Coarse 0.5 – 5kHz (0 – 127) 19
2 OSC Frequency Fine 0 – 127 (0 – 127)
3 LFO Wave tri, sine (0 – 1)
4 LFO Depth 0 – 127 (0 – 127)
5 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
6 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
8—
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 96.
No. Parameter Range Value Table No.
1 Sensitivity 0 – 127 (0 – 127)
2 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
3 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
4 Attack Time 0.3ms – 227ms (0 – 127) 17
5 Release Time 2.6ms – 2171ms (0 – 127) 18
6 Release Curve 0 – 127 (0 – 127)
7 Direction up, down (0 – 1)
8 Dyna Threshold Level 0 – 127 (0 – 127)
9 Dyna Level Offset 0 – 127 (0 – 127)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 96.
No. Parameter Range Value Table No.
1 Filter Type LPF (12dB), LPF (18dB), LPF
(24dB), HPF, BPF, BEF
(0 – 5)
2 Sensitivity 0 – 127 (0 – 127)
3 Dyna Level Offset 0 – 127 (0 – 127)
4 Resonance -16 – +111 (0 – 127)
5 Attack Time 0.3ms – 227ms (0 – 127) 17
6 Release Time 2.6ms – 2171ms (0 – 127) 18
7 Release Curve 0 – 127 (0 – 127)
8 Direction up, down (0 – 1)
9 Dyna Threshold Level 0 – 127 (0 – 127)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 96.
No. Parameter Range Value Table No.
1 Mod Speed 0 – 127 (0 – 127)
2 Mod Wave Type Type A, Type B, Type C,
Typ e D
(0 – 3)
3 Mod Depth 0 – 127 (0 – 127)
4 Mod Depth Ofst R -63 – +63 (1 – 127)
5 HPF Cutoff Frequency 20Hz – 8.0kHz (0 – 52) 3
6 LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
7 Delay Time 0.1 – 370.0ms (1 – 3700)
8 Delay Time Ofst R 0 – 884 (0 – 884)
9 Delay Level 0 – 127 (0 – 127)
10 Dry Mix Level 0 – 127 (0 – 127)
11 Feedback Level -63 – +63 (1 – 127)
12 FB Level Ofst R -63 – +63 (1 – 127)
13 AM Speed 0.00Hz – 39.7Hz (0 – 127) 1
14 AM Wave tri, sine, saw up, saw down (0 – 3)
15 AM Depth 0 – 127 (0 – 127)
16 AM Inverse R normal, inverse (0 – 1)
No. Parameter Range Value Table No.
1 On/off Switch on, off (0 – 1)
2 Low Level -64 – +63 (0 – 127)
3 Mid Level -64 – +63 (0 – 127)
4 High Level -64 – +63 (0 – 127)
5 Low Mute off/on (0 – 1)
6 Mid Mute off/on (0 – 1)
7 High Mute off/on (0 – 1)
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 Divide Type 16th – 4th (5 – 11) 14
2 Gate Time 0 – 100% (0 – 100)
3 Pan AEG Type A – E (0 – 4)
4 Pan AEG Min Level 0 – 127 (0 – 127)
5 Pan Depth -63 –+63 (1 – 127)
6 Divide Min Level 0 – 127 (0 – 127)
7 Pan Type A – J (0 – 9)
8 Overdrive 0 – 127 (0 – 127)
9 AEG Phase 0 – 15 (x 16th note) (0 – 15)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 96.
No. Parameter Range Value Table No.
1 Mod Speed 0 – 127 (0 – 127)
2 Mod Depth 0 – 127 (0 – 127)
3 Mod Gain -12 – +12dB (52 – 76)
4 Mod Mix Balance D63>W – D=W – D<W63 (1 – 127)
5 Pre Mod HPF Cutoff
Frequency
20Hz – 8.0kHz (0 – 52) 3
6 Mod LPF Cutoff Frequency 1.0kHz – 20.0kHz (34 – 60) 3
7 Mod LPF Resonance 1.0 – 12.0 (10 – 120)
8 Delay Time 0.1 – 740.0ms (1 – 7400)
9 Delay Time Ofst R 0 – 884 (0 – 884)
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Feedback Level -63 – +63 (1 – 127)
12 FB Level Ofst R -63 – +63 (1 – 127)
13 Feedback Hi Damp 0.1 – 1.0 (1 – 10)
14 FB Hi Damp Ofst R -0.9 – +0.9 (1 – 19)
15 —
16 —
No. Parameter Range Value Table No.
1 EQ1 (LSH) Frequency 31.5Hz – 2.0kHz (12 – 84) 30
2 EQ1 (LSH) Gain -12.0dB – +12.0dB (60 – 300)
3 EQ2 Q 0.50 – 16.00 (0 – 60) 31
4 EQ2 Frequency 50.0 Hz – 20.0kHz (20 – 124) 30
5 EQ2 Gain -18.0dB – +18.0dB (0 – 360)
6 EQ3 Q 0.50 – 16.00 (0 – 60) 31
7 EQ3 Frequency 50.0 Hz – 20.0kHz (20 – 124) 30
8 EQ3 Gain -18.0dB – +18.0dB (0 – 360)
9 EQ4 Q 0.50 – 16.00 (0 – 60) 31
10 EQ4 Frequency 50.0 Hz – 20.0kHz (20 – 124) 30
11 EQ4 Gain -18.0dB – +18.0dB (0 – 360)
12 EQ5 (HSH) Frequency 500Hz – 20.0kHz (60 – 124) 30
13 EQ5 (HSH) Gain -12.0dB – +12.0dB (60 – 300)
14 Output Level -12.0dB – +12.0dB (60 – 300)
15
16
No. Parameter Range Value Table No.