User Manual

MOTIF XF Data List
98
Effect Parameter List
Category — PHASER
[1] VCM PHASER MONO
The Color parameter is not available in the following conditions: When Mode is set to 1 and Stage
is set to 4, 6, 8. 12 or 16; or when Mode is set to 2 and Stage is set to 4 or 10.
[2] VCM PHASER STEREO
The Color parameter is not available in the following conditions: When Mode is set to 1 and Stage
is set to 4, 6, or 8; or when Mode is set to 2 and Stage is set to 4 or 10.
[3] TEMPO PHASER
[4] DYNAMIC PHASER
Category — TREMOLO&ROTARY
[1] AUTO PAN
[2] TREMOLO
[3] ROTARY SPEAKER
Category — DISTORTION
[1] AMP SIMULATOR 1
No. Parameter Range Value Table No.
1 Speed 0.100Hz – 10.00Hz (0 – 252) 23
2 Manual 0 – 127 (0 – 127)
3 Depth 0 – 127 (0 – 127)
4 Feedback 0 – 127 (0 – 127)
5 Stage 4, 6, 8, 10, 12, 16 (0 – 5)
6 Mode 1, 2, 3 (0 – 2)
7 Color 0 – 127 (0 – 127)
8—
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 Speed 0.100Hz – 10.00Hz (0 – 252) 23
2 Manual 0 – 127 (0 – 127)
3 Depth 0 – 127 (0 – 127)
4 Feedback 0 – 127 (0 – 127)
5 Stage 4, 6, 8, 10 (0 – 3)
6 Mode 1, 2 (0 – 1)
7 Color 0 – 127 (0 – 127)
8 Spread 0 – 127 (0 – 127)
9—
10 —
11 —
12 —
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 LFO Speed 16th – 4thx16 (5 – 29) 14
2 LFO Depth 0 – 127 (0 – 127)
3 Phase Shift Offset 0 – 127 (0 – 127)
4 Feedback Level -63 – +63 (1 – 127)
5 LFO Phase Reset off (free run), Key On Reset,
SEQ Start Reset
(0 – 2)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 96.
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Stage 4 – 22 (4 – 22)
12 Diffusion mono, stereo (0 – 1)
13 —
14 —
15 —
16 —
No. Parameter Range Value Table No.
1 Sensitivity 0 – 127 (0 – 127)
2 Dyna Level Offset 0 – 127 (0 – 127)
3 Feedback Level -63 – +63 (1 – 127)
4 Attack Time 0.3ms – 227ms (0 – 127) 17
5 Release Time 2.6ms – 2171ms (0 – 127) 18
6 Release Curve 0 – 127 (0 – 127)
7 Direction up, down (0 – 1)
8 Dyna Threshold Level 0 – 127 (0 – 127)
9—
10 Dry/Wet Balance D63>W – D=W – D<W63 (1 – 127)
11 Stage 4, 5, 6 (4 – 6)
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 96.
No. Parameter Range Value Table No.
1 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
2 L/R Depth 0 – 127 (0 – 127)
3 F/R Depth 0 – 127 (0 – 127)
4 PAN Direction L<>R, L>>R, L<<R, Lturn,
Rturn, L/R
(0 – 5)
5 LFO Wave 0 – 28 (0 – 28)
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 96.
10 —
11 EQ Mid Frequency 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain -12dB – +12dB (52 – 76)
13 EQ Mid Width 0.1 – 12.0 (1 – 120)
14 —
15 Input Mode mono, stereo (0 – 1)
16 —
No. Parameter Range Value Table No.
1 LFO Speed 0.0Hz – 39.70Hz (0 – 127) 1
2 AM Depth 0 – 127 (0 – 127)
3 PM Depth 0 – 127 (0 – 127)
4—
5—
6 – 9: Same as the parameters shaded in gray in CROSS DELAY on page 96.
10 —
11 EQ Mid Frequency 100Hz – 10.0kHz (14 – 54) 3
12 EQ Mid Gain -12dB – +12dB (52 – 76)
13 EQ Mid Width 0.1 – 12.0 (1 – 120)
14 LFO Phase difference -180deg – +180deg (4 – 124)
15 Input Mode mono, stereo (0 – 1)
16 —
No. Parameter Range Value Table No.
1 Rotor Speed Slow 0.0Hz – 2.65Hz (0 – 63) 1
2 Horn Speed Slow 0.0Hz – 2.65Hz (0 – 63) 1
3 Rotor Speed Fast 0.0Hz – 39.70Hz (64 – 127) 1
4 Horn Speed Fast 0.0Hz – 39.70Hz (64 – 127) 1
5 Slow-Fast Time of R 0 – 127 (0 – 127)
6 Slow-Fast Time of H 0 – 127 (0 – 127)
7 Drive Rotor 0 – 127 (0 – 127)
8 Drive Horn 0 – 127 (0 – 127)
9 Rotor/Horn Balance R63>H – R=H – R<H63 (1 – 127)
10 —
11 – 14: Same as the parameters shaded in gray in CROSS DELAY on page 96.
15 Mic L-R Angle 0deg – 180deg (0 – 60)
16 Speed Control Slow, Fast (0 – 1)
No. Parameter Range Value Table No.
1 Overdrive 0 _ 100% (0 – 100)
2 Device Transistor, Vintage Tube,
Distortion 1, Distortion 2,
Fuzz
(0 – 4)
3 Speaker Type Flat, Stack, Combo, Twin,
Radio, Megaphone
(0 – 5)
4 Presence -10 _ 10 (0 – 20)
5 Output Level 0 _ 100% (0 – 100)
6—
7—
8—
9—
10 Dry/Wet Balance D63>W _ D=W _ D<W63 (1 – 127)
11 —
12 —
13 —
14 —
15 —
16 —