manual

Editing a Performance
MOTIF XF Reference Manual
106
Voice mode Song mode Pattern mode Mixing mode Master mode Utility mode File mode
Performance
mode
Sampling
mode 1
Sampling
mode 2
Reference
Audio In settings—[F4] Audio In
You can set parameters related to audio input from the A/D
INPUT connector and the IEEE1394 connector.
n The FW settings (FW1 –14) are available only when the
optional FW16E is installed.
1 Volume
Determines the output level of the Audio Input Part.
Settings: 0 – 127
2 Pan
Determines the stereo pan position of the Audio Input Part.
Settings: L63 (far left) – C (center) – R63 (far right)
3 Mono/Stereo
Determines the signal configuration for the Audio Input Part,
or how the signal or signals are routed (stereo or mono).
Settings: L mono, R mono, L+R mono, stereo
L mono
Only the L channel of the audio input is used.
R mono
Only the R channel of the audio input is used.
L+R mono
The L and R channels of the audio input are mixed and processed in
mono.
stereo
Both the L and R channels of the audio input are used.
4 Output Select
Determines the output jack assignment for the Audio Input
Part.
Settings: See the table below.
n You can call up the list and select the desired item by pressing
the [SF6] LIST button. For details, see page 37.
5 Reverb Send
Determines the Send level of the Audio Input Part signal
sent to the Reverb effect. The higher the value, the deeper
the reverb.
Settings: 0 – 127
6 Chorus Send
Determines the Send level of the Audio Input Part signal
sent to the Chorus effect. The higher the value, the deeper
the Chorus.
Settings: 0 – 127
7 Dry Level
Determines the level of the Audio Input Part which has not
been processed with the System Effects (Reverb, Chorus).
The higher the value, the shallower the Reverb and Chorus.
Settings: 0 – 127
From this display, you can set the Insertion Effect Types
applied to the Audio Input signal in the Performance mode.
The System Effect can be set in the Effect display
(page 107). Keep in mind that the Insertion Effect cannot
be applied to the audio input signal via the IEEE1394
connector.
1 INSERTION CONNECT (Insertion Connection)
From this display you can set the effect routing for Insertion
effects A and B. The setting changes are shown on the
diagram in the display, giving you a clear picture of how the
signal is routed.
Settings: Ins A F B, Ins B F A
Output Settings—[SF1] Output
LCD Output jacks Stereo/Mono
L&R OUTPUT L and R Stereo
asL&R ASSIGNABLE OUTPUT L and R Stereo
FW1&2 FW OUTPUT 1 and 2 Stereo (1: L, 2: R)
FW3&4 FW OUTPUT 3 and 4 Stereo (3: L, 4: R)
FW5&6 FW OUTPUT 5 and 6 Stereo (5: L, 6: R)
FW7&8 FW OUTPUT 7 and 8 Stereo (7: L, 8: R)
FW9&10 FW OUTPUT 9 and 10 Stereo (9: L, 10: R)
FW11&12 FW OUTPUT 11 and 12 Stereo (11: L, 12: R)
FW13&14 FW OUTPUT 13 and 14 Stereo (13: L, 14: R)
asL ASSIGNABLE OUTPUT L Mono
asR ASSIGNABLE OUTPUT R Mono
1
2
3
4
6
5
7
FW1 FW OUTPUT 1 Mono
:: :
FW14 FW OUTPUT 14 Mono
ins L
(A/D input only)
Internal Vocoder Module Mono
Insertion Effect Connection of A/D Input
—[SF2] Connect
LCD Output jacks Stereo/Mono
2
3
1