Operation Manual
Table Of Contents
- INTRODUCTION
- IMPORTANT MANUAL INFORMATION
- TABLE OF CONTENTS
- SAFETY INFORMATION
- DESCRIPTION
- INSTRUMENT AND CONTROL FUNCTIONS
- Immobilizer system
- Main switch/steering lock
- Indicator lights and warning lights
- Multi-function meter unit
- Handlebar switches
- Clutch lever
- Shift pedal
- Brake lever
- Brake pedal
- ABS (for ABS models)
- Fuel tank cap
- Fuel
- Fuel tank breather hose and overflow hose
- Catalytic converter
- Seat
- Helmet holder
- Storage compartment
- Handlebar position
- Adjusting the shock absorber assembly
- Sidestand
- Ignition circuit cut-off system
- FOR YOUR SAFETY – PRE-OPERATION CHECKS
- OPERATION AND IMPORTANT RIDING POINTS
- PERIODIC MAINTENANCE AND ADJUSTMENT
- Owner’s tool kit
- Periodic maintenance chart for the emission control system
- General maintenance and lubrication chart
- Removing and installing the cowling and panels
- Checking the spark plugs
- Engine oil and oil filter cartridge
- Coolant
- Replacing the air filter element
- Adjusting the engine idling speed
- Checking the throttle grip free play
- Valve clearance
- Tires
- Cast wheels
- Adjusting the clutch lever free play
- Checking the brake lever free play
- Brake light switches (for ABS models)
- Brake light switches (for non-ABS models)
- Checking the front and rear brake pads
- Checking the brake fluid level
- Changing the brake fluid
- Drive chain slack
- Cleaning and lubricating the drive chain
- Checking and lubricating the cables
- Checking and lubricating the throttle grip and cable
- Checking and lubricating the brake and shift pedals
- Checking and lubricating the brake and clutch levers
- Checking and lubricating the sidestand
- Lubricating the swingarm pivots
- Checking the front fork
- Checking the steering
- Checking the wheel bearings
- Battery
- Replacing the fuses
- Replacing the headlight bulb
- Replacing the tail/brake light bulb
- Replacing a turn signal light bulb
- Replacing the license plate light bulb
- Replacing the auxiliary light bulb
- Supporting the motorcycle
- Front wheel (for non-ABS models)
- Rear wheel (for non-ABS models)
- Troubleshooting
- Troubleshooting charts
- MOTORCYCLE CARE AND STORAGE
- SPECIFICATIONS
- CONSUMER INFORMATION
PERIODIC MAINTENANCE AND ADJUSTMENT
6-12
6
TIP
An oil filter wrench is available at a
Yamaha dealer.
6. Apply a thin coat of clean engine
oil to the O-ring of the new oil filter
cartridge.
TIP
Make sure that the O-ring is properly
seated.
7. Install the new oil filter cartridge
with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.
8. Install the engine oil drain bolt and
its new gasket, and then tighten
the bolt to the specified torque.
9. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
NOTICE
ECA11620
● In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
● Make sure that no foreign mate-
rial enters the crankcase.
1. O-ring
1. Torque wrench
Tightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)
1
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter cartridge replace-
ment:
2.50 L (2.64 US qt, 2.20 Imp.qt)
With oil filter cartridge replacement:
2.80 L (2.96 US qt, 2.46 Imp.qt)
U20SE3E0.book Page 12 Monday, April 23, 2012 10:47 AM