Owner's Manual

14 XM4180/XM4080/XH200 Owner’s Manual
● XH200
* These specifications apply to rated power supplies of 120V, 230V and 240V.
0 dBu=0.775 Vrms, Half Power=1/2 Output Power (3 dB below rated power)
Specifications and descriptions in this owner’s manual are for information pur-
poses only.
Yamaha Corp. reserves the right to change or modify products or specifications
at any time without prior notice. Since specifications, equipment or options may
not be the same in every locale, please check with your Yamaha dealer.
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 25A
Conforms to Environments: E1, E2, E3 and E4
■ MONITOR/REMOTE PIN layout
Output Power* 40 Hz–20 kHz
THD+N= 0.1 %
70 V, RL=25 Ω
MIN
200 W x 2
100 V, RL=50 Ω 200 W x 2
Power Consumption Standby 5 W
Idle 40 W
1/8 (70 V, RL=25 Ω/Pink noise) 400 W
THD+N 40 Hz–20 kHz, Half Power MAX 0.1 %
Intermodulation Distortion 60 Hz:7 kHz, 4:1, Half Power MAX 0.1 %
Frequency Response Po=1 W, HPF=40 Hz,
80 Hz–20 kHz
MAX 0 dB
TYP 0 dB
MIN -0.5 dB
SN Ratio (DIN AUDIO) MIN 103 dB
Channel Separation Half Power, 1 kHz, Att. max, input 600 Ω shunt MIN 60 dB
Residual Noise Att. min, (DIN AUDIO) MAX -65 dBu
Input Sensitivity Att. max TYP +4 dBu
Voltage Gain Att. max TYP 38 dB (100 V), 35 dB (70 V)
Maximum Input Voltage MIN +22 dBu
Input Impedance TYP 20 kΩ (balanced), 10 kΩ (unbalanced)
Controls Front Panel POWER switch (push on/push off)
attenuator (31 position) x 2
Rear Panel OUTPUT VOLTAGE switch (100 V/70 V) x 1
HPF switch (40 Hz/80 Hz 12 dB/oct) x 2
Connectors INPUT Euroblock connector (balanced) /ch
SPEAKERS Barrier strip/ch
MONITOR/REMOTE Dsub 15P x 1
Indicators POWER/STANDBY x 1 (Green/Orange)
SIGNAL x 2 (Green)
CLIP/LIMIT x 2 (Red)
PROTECT/MUTE x 1 (Red)
Load Protection POWER switch on/off mute
DC-fault: output relay off/restored automatically.
Clip limiting : THD ≥ 0.5 %
Amplifier Protection Thermal: Cuts the output (when heatsink temp. ≥ 90 °C);
operation restored automatically.
VI limiter (RL ≤ 16
Ω): Limits the output.
Power Supply Protection Thermal: Power supply shutdown (when temp. ≥ 90 °C);
operation not restored automatically.
Cooling Variable-speed fan x 1
Power Requirements 120V, 220V–240V; 50Hz/60Hz
Dimensions (W x H x D) 480 x 88 x 412 mm (18-7/8" x 3-7/16" x 16-1/4")
Weight 9.8 kg (21.6 lbs)
Included Accessories Power cord, Security cover, Owner’s Manual,
3-pin Euroblock connector x 2
Pin
No.
Signal
Description
XM4180/XM4080 XH200
1 GND
2 REMOTE CONTROL STANDBY STANDBY STANDBY Control: Supply 5 VDC, 5 mADC
3 MONITOR MODEL ID MODEL ID XM4180: 560 Ω, XM4080: 680 Ω, XH200: 820 Ω (Impedance to GND)
4 REMOTE CONTROL MUTE CH D – MUTE Control: Connect to GND, +5 V, 1 mA
5 MUTE CH C MUTE CH B
6 MUTE CH B –
7 MUTE CH A MUTE CH A
8 MONITOR PROTECT STATUS CH D – PROTECTION Off/ Output On: +5 VDC, Zo=270 Ω
PROTECTION On/ Output Off: 0 VDC, Zo=High
9PROTECT STATUS CH C PROTECT STATUS CH B
10 PROTECT STATUS CH B –
11 PROTECT STATUS CH A PROTECT STATUS CH A
12 OUTPUT LEVEL CH D – XM4180, XM4080
+4dBu (-27.2 dB of Speaker Output Level) at 100 W/8Ω, RL=7.5 kΩ, Zo=300 Ω
XH200
-33.2 dB of Speaker Output Level, RL=7.5 kΩ, Zo=300 Ω
13 OUTPUT LEVEL CH C OUTPUT LEVEL CH B
14 OUTPUT LEVEL CH B –
15 OUTPUT LEVEL CH A OUTPUT LEVEL CH A
42