XW-CS-700 Wireless extension microphone kit for the Yamaha CS-700 Congratulations on your purchase of the XW-CS-700, a wireless extension microphone kit for the Yamaha CS-700. The XW-CS-700 allows additional microphone pick-up in a room without having to wire the room with audio cables, allowing for a clean extension of the microphone capture of the Yamaha CS-700. Please read the safety documentation for the components that are part of the XW-CS-700 kit carefully and follow their instructions.
Components The XW-CS-700 kit includes the following components. Please check that you received all of them: 1 Revolabs™ HD dual™: The HD dual includes the Receiver for the wireless microphone, the Charger to charge up to two microphones, and the required power adapters. 1 Revolabs HD™ omni-directional wireless microphone. 1 Proprietary audio cable to connect the HD dual Receiver to the CS-700. 1 User guide (this document).
Pairing the wireless microphone to the Receiver Pairing creates a link between the wireless microphone and the Receiver, with a unique identifier. This process only needs to be done once. Afterwards the microphone will automatically try to connect to the same Receiver whenever it is lifted from the Charger or otherwise switched on.
Setting the DIP-witches Please ensure that the DIP switches on the back of the Receiver are set as bellow: This setting ensures that the output of the Receiver provides mixed audio from microphone one and two in case more than one microphone is being used (DIP 1), that no Low-pass filter is activated (DIP 2), that the Receiver provides miclevel output (DIP 3), that the mute button on the microphone is not being used, audio will be sent in all cases (DIP 4), no EQ will be applied (DIP 5 & 6), and the highes
Connecting the Wireless Receiver to the Yamaha CS-700 The proprietary audio cable included in the kit allows to connect the wireless Receiver to the CS-700 unit. Plug the 3.5mm side of the cable into the “Ch1 Out” receptacles. Ensure that DIP switch 1 was set to “On” ensuring that the output carries both audio streams in case two microphones are being used. Connect the other side of the audio cable to the extension microphone connector on the back of the CS-700.
Using the Omni-Directional Tabletop Wireless Microphone The Omni-directional Tabletop Wireless Boundary Microphone enables multiple conference attendees to use a single microphone. 360 º pickup pattern 1 2 3 6 5 4 1. LED display — visual status for microphone status, like not-yet-activated, activated, and pairing. 2. Mute button — if DIP switches are configured as described above, this button will allow to activate the microphone after it has been taken out of the Charger but has no effect thereafter.
Microphone Indicator lights The LED indicator on the microphone and the Receiver can change based on the current state the microphone is in. Please see the below table of possible LED indicators. Note that this table is based on the DIP-settings earlier discussed in this document. If different DIP-settings are selected other behavior might be seen. Equipment Use Microphone LED Microphone in Charger Solid RED Solid GREEN OFF Receiver Channel LEDs OFF OFF OFF Two RED flashes every 1.
2. Place the microphone unit into pairing mode by holding the button down for seven seconds. The LED will first turn green, then solid red. Release the button once the LED is red. The microphone is now in pairing mode. 3. Within one minute, push and hold the button for channel two on the Receiver for seven seconds until the LED turns solid red, then release.
Muting the wireless microphone has no impact on the CS-700 mute status. Once the LED light of the microphone is blinking green, pressing the mute button should have no effect – the LED should remain green. If the LED changes colors from green blinking to red blinking and back whenever the mute button is pressed, the DIP switch setting on the Receiver is incorrect. Recheck and correct the DIP-switch settings and restart the Receiver.
© Yamaha Corporation. All Rights Reserved. Published 05/2019 SC-XWCS-201905-EN/ 2950305-00 V 1.0 Manufacturer: Yamaha Unified Communications, Inc.