English Français YDP - 184 Owner’s Manual Mode d’emploi Before using the instrument, be sure to read “PRECAUTIONS” on pages 5-6. For information on assembling the instrument, refer to the instructions at the end of this manual. Avant d’utiliser l’instrument, lisez attentivement la section « PRÉCAUTIONS D’USAGE » aux pages 5 et 6. Pour plus d’informations sur l’assemblage de l’instrument, reportez-vous aux instructions figurant à la fin de ce manuel.
For YDP-184 SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind.
For YDP-184 COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Address : Telephone : Type of Equipment : Model Name : Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620 714-522-9011 Digital Piano YDP-184 This device complies with Part 15 of the FCC Rules.
For the AC adaptor This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. For AC adaptor WARNING CAUTION • This AC adaptor is designed for use with only Yamaha electronic instruments. Do not use for any other purpose. • Indoor use only. Do not use in any wet environments. • When setting up, make sure that the AC outlet is easily accessible.
CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following: Power supply/AC adaptor Handling caution • Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.
NOTICE Information To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below. About copyrights Handling • Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise.
Included Accessories Owner’s Manual (this book) “50 Classical Music Masterpieces” (Music Book) Online Member Product Registration You will need the PRODUCT ID on the sheet in order to fill out the User Registration form. Power cord*, AC adaptor* Bench* Warranty* * May not be included depending on your area. Check with your Yamaha dealer. About the Manuals This instrument has the following documents and instructional materials.
Online Materials (Downloadable from the web) iPhone/iPad Connection Manual Explains how to connect the instrument to smart devices, such as iPhone, iPad, etc. Computer-related Operations Includes instructions on connecting this instrument to a computer, and operations related to transferring song data. MIDI Reference Contains the MIDI-related information. To obtain these manuals, access the Yamaha Downloads. Yamaha Downloads http://download.yamaha.
Features Full-scale piano performance page 22 This instrument features a piano Voice created with samples of the Yamaha CFX flagship concert grand piano, as well as the incredibly realistic keyboard feel that recreates the sensation of playing an acoustic instrument. By using a similar hammer mechanism (with no springs) as is found in a grand piano, the GH3 keyboard action reproduces the touch of an acoustic instrument, from the heavier feel in the lower register to the lighter touch in the upper octaves.
Table of Contents PRECAUTIONS ....................................................5 Handling Song Files .................................................60 NOTICE ......................................................................7 Information ................................................................7 Included Accessories ..................................................8 About the Manuals .....................................................8 Features ..........................................
Introduction Panel Controls and Terminals Control Panel A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1 A1 B1 3 4 5 7 6 8 9 ) ! @ # $ % ^ 1 [P] (Standby/On) switch.................... page 15 For turning the power on or setting it to standby. 2 [MASTER VOLUME] slider ............... page 17 For adjusting the overall volume. 3 [u]/[d]/[<]/[>] buttons, display......... page 20 For selecting an item or setting a value using the buttons corresponding to the display indication. 4 [FUNCTION] button .
Panel Controls and Terminals 1 2 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7 Music rest (page 16) Key cover (page 14) DC IN jack (page 14) USB [TO DEVICE] terminal (page 68) Terminal panel (page 66) Terminal panel (page 66) Pedals (page 19) [PHONES] jacks (page 18) YDP-184 Owner’s Manual 13
Getting Started — Playing the Piano This section explains how to set up and start using your instrument. Setup is so simple, you can start playing right away. Turning the Power On or Off 1. CAUTION When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Connect the power cord and AC adaptor.
Getting Started — Playing the Piano 4. Press the [P] (Standby/On) switch at the right end of the front panel to turn the power on. The display located at the left end of the front panel and the power indicator located below the left end of the keyboard both light up. [P] (Standby/On) switch NOTICE Press only the [P] (Standby/ On) switch when turning the power on. Any other operations, such as pressing the keys, buttons or pedals may cause the instrument to malfunction. The power indicator lights up. 5.
Getting Started — Playing the Piano Auto Power Off function To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automatically turns the power off if the instrument is not operated for a specified period of time. The amount of time that elapses before the power is automatically turned off is approximately 30 minutes by default; however, you can change the setting (page 90).
Getting Started — Playing the Piano Setting the Volume — [MASTER VOLUME] To adjust the volume, use the [MASTER VOLUME] slider located at the right of the panel. Play the keyboard to actually produce sound while you adjust the volume. Increases the level. Decreases the level. Master Volume: The volume level of the entire keyboard sound. Adjusting the [MASTER VOLUME] slider also affects the output level of the [PHONES] jacks and the output level of the AUX OUT jacks.
Getting Started — Playing the Piano Using Headphones Connect a pair of headphones to one of the [PHONES] jacks. When the headphones are plugged into either of the [PHONES] jacks, the internal speaker system is automatically shut off. Two [PHONES] jacks are provided. Two sets of standard stereo headphones can be plugged in. (If you are using only one pair of headphones, you can plug them into either of these jacks.
Getting Started — Playing the Piano Using the Pedals This instrument is equipped with three foot pedals: damper pedal (right), sostenuto pedal (center), and soft pedal (left). Damper pedal (right pedal) When you press the damper pedal, the notes you play have a longer sustain. When you select a Voice in the Piano group, pressing the damper pedal activates the VRM (page 25) to accurately recreate the unique resonance of an acoustic grand piano’s soundboard and strings.
Basic Operations on Display On the screen display, you can call up three main functions: Voice, Song and Demo. In addition, various detailed settings can be made, for even greater playability and performance potential. Select a Voice, Song or Demo Song When this is shown here, you can scroll through the display vertically. Selecting Voices Select from the list, or change the display. 1. Press the [VOICE] button to call up the Voice List display. 2. Press the [u] or [d] button to select a Voice group.
Basic Operations on Display Voice: Instrument sound for playing from the keyboard. In addition to the Piano sounds, a wide variety of other musical instrument sounds are available. Song: A piece of music for listening enjoyment or for playing back and practicing along with. Demo: Voice Demos let you experience the characteristics of the Voices. Voice display This indicates the current position in the Voice group. [r] to select a Voice. [u] to return. [r] to select a Voice. [l] to return. 3.
Main Operations Playing Various Musical Instrument Sounds (Voices) This instrument put the sound of renewed Yamaha's CFX concert grand piano sound with a wide dynamic range for maximum expressive control. In addition to the wonderfully realistic piano sounds, you can select and play other musical instrument sounds. Selecting Voices from the panel directly 1 1. Press the [CFX GRAND] button or the [STRINGS] button.
Playing Various Musical Instrument Sounds (Voices) Selecting Voices The Voices of the instrument are conveniently divided into groups of instrument types. Select a desired Voice and play the piano. NOTE To hear and experience the characteristics of the Voices, listen to the Demo Songs for each Voice (page 37). NOTE 2, 3, 4 Touch Response (page 87) will not be applied to some Voices. For information about the Voices to which Touch Response can be applied, refer to the “Preset Voice List” on page 94.
Playing Various Musical Instrument Sounds (Voices) 4. Use the [u]/[d] buttons to scroll through the Voice list, and then press the [r] button to select the desired Voice. The currently selected Voice name is shown in the display. Voice display You can select other Voices in order using the [l]/[r] buttons via the Voice display. Press the [u] button to go back to the Voice List display. 5. NOTE You can specify the Touch Response (how the sound responds to the way you play the keys).
Playing Various Musical Instrument Sounds (Voices) What you can do in the Piano Room Item Icon Default settings Descriptions Setting Range Lid Position Determines how much the Lid is opened. Full Full, Half, Close Brightness Adjusts the brilliance of sound. Differs depending on the Voice. 0 – 10 Touch Determines how the sound responds to your playing strength. You should adjust this setting according to the specific Voice you’re playing or the particular Song you’re performing, as desired.
Playing Various Musical Instrument Sounds (Voices) What is VRM? The VRM (Virtual Resonance Modeling) function uses sophisticated physical modeling to simulate the actual string resonance sound that occurs when the damper pedal on a real piano is pressed or keys are played and held.
Playing Various Musical Instrument Sounds (Voices) Enhancing and Customizing the Sound Applying the following effects gives you greater and richer expressive capabilities. Brilliance For adjusting the brightness of the sound. This setting is applied commonly to all parts (keyboard Voices/Song/MIDI). 1 1. 1 Press the [FUNCTION] button repeatedly to call up the “System” menu display, then select the highlighted item in each display as illustrated below.
Playing Various Musical Instrument Sounds (Voices) Reverb This control adds reverberation to the sound by simulating the natural reverberation of a concert hall. The ideal Reverb type is automatically selected whenever you select a Voice, but you can select any of the available Reverb types. To select a desired Reverb type, use the “Voice” menu display: “Reverb” (page 78). You can also select the Reverb type for Voices in the Piano group from the Piano Room display (page 25).
Playing Various Musical Instrument Sounds (Voices) Playing Two Voices Simultaneously (Dual) Two Voices can be played simultaneously. You can create warm and richly textured Voices by using Voices from different groups simultaneously in a layer, or by using Voices in the same group. 2 2 1. 1, 4 To enter the Dual mode, press the [DUAL/SPLIT] button once so that the lamp lights in red. Voice 1 Lit in red NOTE Voice 2 The Voice which is displayed at top is Voice 1, and the one at bottom is Voice 2. 2.
Playing Various Musical Instrument Sounds (Voices) Splitting the Keyboard Range and Playing Two Different Voices (Split Mode) Split mode enables you to play two different Voices on the keyboard—one with your left hand and another with your right. 2 2 1. 1, 3, 4 To enter the Split mode, press the [DUAL/SPLIT] button repeatedly to light it in green. Voice R Lit in green Voice L The Voice which is displayed at top is Voice R, and the one at bottom is Voice L. 2.
Playing Various Musical Instrument Sounds (Voices) Using Dual and Split Simultaneously 2 2 1. 1, 4 To enter the Dual and Split modes simultaneously, press the [DUAL/SPLIT] button repeatedly so that the lamp lights in orange. Voice R1 Lit in orange Voice R2 Voice L The Voice which is displayed at top is Voice R1, and the one in the middle is Voice R2, and the one at bottom is Voice L. 2. Select the Voices for layering and for the left-hand area. 2-1.
Playing Various Musical Instrument Sounds (Voices) Playing Duo This function allows two different players to play the instrument, one on the left and the other on the right. This is convenient for practicing duets over the same octave range. 1 1 2 4 1. Press the [FUNCTION] button repeatedly to call up the “System” menu display, and then select the highlighted item in each display as illustrated below. “System” menu display Keyboard display 1-1. Use the [u]/[d] buttons 1-3.
Playing Various Musical Instrument Sounds (Voices) 2. Press the [EXIT] button to exit from the menu display. When Duo is on, the [DUAL/SPLIT] button is lit in green and the [Duo] is shown on the Voice display. Lit in green 3. Play the keyboard. The sound of left-hand range is emitted from the left, the sound of righthand range is emitted from the right. 4. Press the [DUAL/SPLIT] button to exit from the Duo mode. You can also exit from the Duo mode by following either of the instructions below.
Playing Various Musical Instrument Sounds (Voices) Adjusting the Tempo 2 3 1 Metronome 1. Press the [TEMPO] button to call up the Tempo display. Tempo value 2. 3. Use the [<]/[>] buttons to adjust the tempo. NOTE You can adjust the tempo value (number of beats per minute) using the [<]/[>] buttons. To reset the tempo to the default setting, press the [<] and [>] buttons simultaneously. For information on setting the time signature, refer to page 34.
Playing Various Musical Instrument Sounds (Voices) 3. Use the [u]/[d] buttons to select the desired time signature. Setting range: 2/2, 1/4, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 3/8, 6/8, 7/8, 9/8, 12/8 Default setting: 4/4 (Selecting a MIDI Song will change the tempo value to that specified in the selected MIDI Song data.) Tempo indication and Setting range Tempo is displayed as “note type=xxx” (For example: =120). Selecting the Time Signature changes the available parameters as follows.
Playing Back Songs This instrument can play Preset Songs, Songs you recorded on this instrument. In addition to listening to these Songs, you can play the keyboard as the Song plays back. MIDI Songs A MIDI Song is comprised of your keyboard performance information and is not a recording of the actual sound itself. The performance information refers to which keys are played, at what timing, and at what strength—just as in a musical score.
Playing Back Songs Listening to the Voice Demos For each Voice group, the instrument contains several Demo recordings that showcase the special characteristics of the corresponding Voices. For information about the Voices which feature Demos that can be played back, refer to the “Preset Voice List” on page 94. 2, 3, 4 1 1. 2. 3. 4, 5 Press the [SONG/DEMO] button to call up the Song list display. Use the [u]/[d] buttons to select “Demo,” and then press the [r] button to call up the next display.
Playing Back Songs Playback of Songs NOTE 2, 3, 4 The instrument can automatically select a Song file saved in the root directory of the USB flash drive as soon as the USB flash drive is connected. For instructions, refer to “USB Autoload” on page 90. 5, 6 2 1. 2. If you want to play back a Song in a USB flash drive, connect the USB flash drive containing Song data to the USB [TO DEVICE] terminal beforehand.
Playing Back Songs 3. Press the [>] button to display the Songs in the specified category, and then select a desired Song using the [u]/[d] buttons. NOTE Press the [<] button to return to the category/folder. When “User” or “USB” category is selected, the icon indicating Song types are shown to the left of the Song name. Song List icon Data format Folder MIDI Songs NOTE “NoSong” will be shown in the display when no data exists in that folder.
Playing Back Songs 6. Press the [R/K] (Play/Pause) button again to stop playback. Even if you don’t press the [R/K] (Play/Pause) button, the Song stops automatically when Song playback reaches the end. Rewind/Fast forward 1. Use the [<] and [>] buttons to move back or forth through the Song (in bars or seconds), while the Song display is shown. Song display Measure number Holding one of the buttons scrolls backward/forward continuously.
Playing Back Songs Playing a One-hand Part — Part Cancel Function Some MIDI Songs, such as Preset Songs, are divided into right-hand and lefthand parts. By using such Song data, you can practice the left hand by turning on only the right-hand part, and practice the right hand by turning on only the left-hand part—allowing you to practice parts separately for easy mastery of difficult material. 2 2, 3 4, 5 1. NOTE The parts can be turned on or off even during playback. Select a Song for practicing.
Playing Back Songs Playing Back a Song Repeatedly There are three Repeat items as follows. These are convenient for repeatedly practicing difficult phrases. It is a good idea to use this function and the Part Cancel function (above) for practicing difficult phrases. • AB Repeat ............. Play a MIDI Song repeatedly by designating a specific range within the Song. • Phrase Repeat ...... Play a MIDI Song repeatedly by designating a phrase or phrases within the Song. • Song Repeat ..........
Playing Back Songs AB Repeat setting Specify the repeat range. 4-1. Press the [R/K] (Play/Pause) button to start Song playback. 4-2. Press the [>] button at the starting point (A) of the range to be repeated. A – B display Specifying the top of a Song as Point A Specify Point A before starting playback, then start playback and specify Point B. Specifying the end of a Song as Point B Specifying only Point A results in repeat playback between Point A and the Song end (as Point B). 4-3.
Playing Back Songs Song Repeat setting 4-1. Select the desired Repeat type using the [u]/[d] buttons in the setting display. Setting display Checkmark • Off: Disables repeated playback. • Single: Plays through the selected file repeatedly. • All: Continuously plays back all Songs within a designated range in order. • Random: Continuously plays back all Songs within a designated range in random order. 4-2. Press the [R/K] (Play/Pause) button to start Repeat playback.
Playing Back Songs Adjusting the Volume Balance You can adjust the Volume balance between the Song playback and the sound you are playing on the keyboard, or between the Right and Left parts of the selected Song. 1, 2, 3 1 4 Select the desired Song beforehand. For instructions, refer to page 38. 1. Press the [FUNCTION] button repeatedly to call up the “Song” menu display. Select “Volume,” and then press the [>] button. “Song” menu display 2.
Playing Back Songs 3. Adjust the Volume balance by using the [<]/[>] buttons. In the case of “Song – Keyboard”: The volume of your playing will be lower. The Song playback volume will be lower. In the case of “Song L – R”: R part volume will be lower. 4. L part volume will be lower. Press the [EXIT] button twice to exit from the “Song” menu display. Whenever you select another MIDI Song, the setting for “Song L – R” is restored to its default setting.
Playing Back Songs Useful Playback Functions Starting/pausing playback by using a pedal You can assign the Song Play/Pause function (equivalent to the [R/K] (Play/ Pause) button) to the center or the left pedal in the “System” menu. Press the [FUNCTION] button repeatedly to call up the “System” menu display, and then select “Pedal” → “Play/Pause” to make the assignment. This is convenient for starting or pausing playback when you are performing and can’t take your hands from the keyboard.
Playing the Keyboard along with Rhythm Playback This instrument features various rhythm patterns. In time with the Rhythm playback, you can enjoy your keyboard performance. About the Rhythm Tempo 2 5 • The Rhythm tempo is equivalent to that set for the Metronome (page 33). • Although you set the Rhythm tempo, selecting a MIDI Song will change the tempo value to that specified in the selected MIDI Song data. Detailed Settings for the Rhythm 1, 4 1. Press the [RHYTHM] button to start Rhythm playback.
Recording Your Performance This instrument allows you to record your performance to the instrument or a USB flash drive as an SMF (format 0) MIDI file. If you want to re-record a specific section or edit parameters such as Voice, use this method. Also you can record your performance to each Track one by one. This instrument allows you to record approximately 500 KB of data per Song. Recording Methods This chapter covers the following four methods. • Quick MIDI Recording ...................................
Recording Your Performance NOTE Quick MIDI Recording If you want to record the lefthand and right-hand parts individually, refer to “MIDI Recording—independent Tracks” (page 52), since the Recording method here assumes that both the left and right parts are being recorded together. This method is the quickest way to start recording. 5 Using the Metronome/ Rhythm 3, 6 2, 4 1. Make the necessary settings such as Voice selection and time signature.
Recording Your Performance 4. After you finish your performance, press the [REC] (Record) button again to stop recording. This operation exits from the Recording mode and calls up the display for saving the recorded performance data. 5. If you want to save the recorded performance, press the [>] button to execute the Save operation while “Save” is highlighted. After the Save operation is completed, the display shows “Save Completed” then returns to the Song display.
Recording Your Performance MIDI Recording — Independent Tracks With MIDI Recording, you can create a MIDI Song consisting of 16 tracks by recording your performance to each track one by one. In recording a piano piece, for example, you can record the right-hand part to Track 1 then record the left-hand part to Track 2, allowing you create a complete piece which may be difficult to play live with both hands together.
Recording Your Performance 5. If you want to save the recorded performance, press the [>] button to execute the Save operation while “Save” is highlighted. After the Save operation is completed, the display shows “Save Completed” then returns to the Song display. The recorded Song will be named “USERSONGxxx” (xxx: number) and saved in the “User” category. NOTICE The recorded MIDI Song will be lost if you change to another Song or you turn the power off without executing the save operation.
Recording Your Performance MIDI Recording to the USB Flash Drive These instructions describe how to overwrite an already recorded MIDI Song in the USB flash drive or how to create a New MIDI Song on the USB flash drive. 1. 2. Connect the USB flash drive to the USB [TO DEVICE] terminal. Select a MIDI Song as Recording target, then enter the Recording mode. 2-1. If you want to record an additional Track to the already recorded MIDI Song, select the desired MIDI Song in the USB flash drive.
Recording Your Performance 3. Execute the Recording operation, then save the recorded performance. • When you want to record additionally to the currently selected MIDI Song, or record to a specified track on a blank MIDI Song: Execute steps 2 – 8 in “MIDI Recording—Independent Tracks” on page 52. NOTICE Note that recording your performance to a Track containing data will overwrite the previously recorded data.
Recording Your Performance Other Recording Techniques Re-recording a MIDI Song in parts You can re-record a specific range of the MIDI Song. 1, 4, 5, 6 2 5, 8 1. 1 4, 7, 10 Set the parameters which determine how recording starts and stops. 1-1. Press the [FUNCTION] button repeatedly to call up the “Recording” menu display. 1-2. Use the [u]/[d] buttons to select “RecStart,” then select the value which determines how recording starts by using the [>] button.
Recording Your Performance 3. Select the desired MIDI Song. For instructions, refer to page 38. 4. Specify the start point you wish to re-record. Use the [<]/[>] buttons to move the playback position (measure number) to the desired point. Alternately, press the [R/K] (Play/Pause) button to start playback, then press the [R/K] button again slightly prior to the desired point. If necessary, select the settings (Voice and other parameters).
Recording Your Performance Changing the tempo or the Voice of a previously recorded MIDI Song You can change the tempo and Voice after recording to change a feel or to set a more suitable tempo. To change the tempo: 3 3, 4 5 2 1. Select the MIDI Song you wish to change. For instructions, refer to page 38. 2. Press the [TEMPO] button to call up the Tempo display, then set the desired Tempo. For instructions, refer to page 34. 3. 4.
Recording Your Performance 5. Press the [EXIT] button to exit from the “Song” menu display. To change the Voice: 1. Select the MIDI Song you wish to change. For instructions, refer to page 38. 2. Select the desired Voice. For instructions, refer to page 23. 3. 4. 5. Press the [FUNCTION] button repeatedly to call up the “Song” menu display, then select the highlighted item in each display as illustrated below. “Song” menu display Edit display 3-1. Use the [u]/[d] buttons 3-3.
Handling Song Files The “File” menu in the “Song” menu display (page 82) enables you to apply various operations to Song files — Songs you recorded on this instrument or commercially available Songs. To connect a USB flash drive, be sure to read the section “Precautions when using the USB [TO DEVICE] terminal” on page 68.
Handling Song Files Basic Song File Operation Song files can be handled via the instructions shown below. 1. 2. Connect the appropriate USB flash drive containing the desired files to the USB [TO DEVICE] terminal. Select a Song for handling. For information on selecting a Song, see page 38. 3. Call up the File mode. 3-1. Press the [FUNCTION] button repeatedly to call up the “Song” menu display. Use the [u]/[d] buttons to select “File” then press the [>] button. “Song” menu display 3-2.
Handling Song Files Deleting Files — Delete For details about Song types which can be deleted, refer to page 60. See page 61 for information on basic operations. The following is a detailed procedure of step 4 on that page. 4-1. While “Delete” is highlighted, press the [>] button to call up the setting display. 4-2. Highlight “Execute” by pressing [d] button, and then press the [>] button. After the Song is deleted, the display returns to the Song List display.
Handling Song Files Copying Files — Copy For details about Song types which can be copied, refer to page 60. Range of the Copy/Move operation USER FILES folder As for a MIDI Song in the “User” category in the instrument, you can Copy/ Move it only to the USER FILES folder on a USB flash drive. Selecting a MIDI Song from “User” for copying/moving automatically specifies the USER FILES folder as the destination.
Handling Song Files Moving Files — Move For details about Song types which can be moved, refer to page 60. See page 61 for information on basic operations. The following is a detailed procedure of step 4 on that page. 4-1. While “Move” is highlighted, press the [>] button to call up the setting display. Move destination File name 4-2. Highlight “Execute” by pressing the [d] button, then press the [>] button.
Handling Song Files Renaming Files — Rename For details about Song types which can be renamed, refer to page 60. See page 61 for information on basic operations. The following is a detailed procedure of step 4 on that page. 4-1. While “Rename” is highlighted, press the [>] button to call up the setting display. Cursor 4-2. Assign a name to the Song. Use the [<]/[>] buttons to move the highlight (underline). Use the [u]/[d] buttons to change the character at the current cursor position.
Connections Connectors CAUTION For information about location of these connectors, refer to “Panel Controls and Terminals” on page 13. Terminals under the keyboard 1 2 Before connecting the instrument to other electronic components, turn off the power of all the components. Also, before turning any components on or off, make sure to set all volume levels to minimum (0). Otherwise, damage to the components, electrical shock, or even permanent hearing loss may occur.
Connections 4 MIDI [IN], [OUT], [THRU] terminals Use MIDI cables to connect external MIDI devices to these connectors. Refer to “Connecting External MIDI Devices” on page 69 for more information. Also, you can connect the iPhone/iPad via an accessory sold separately. Refer to “Connecting to an iPhone/iPad” on page 70. 5 AUX OUT [R] [L/L+R] jacks NOTE These jacks let you connect the instrument to external powered speaker systems, for playing in larger venues at higher volumes.
Connections Connecting USB Devices (USB [TO DEVICE] Terminal) You can connect a USB flash drive or a USB wireless LAN adaptor (sold separately) to the USB [TO DEVICE] terminal. You can save data you’ve created on the instrument to the USB flash drive (pages 60, 92), or you can connect the instrument to a smart device such as an iPad via wireless LAN (page 70). Precautions when using the USB [TO DEVICE] terminal This instrument features a built-in USB [TO DEVICE] terminal.
Connections Connecting to a Computer (USB [TO HOST] Terminal) By connecting a computer to the USB [TO HOST] terminal, you can transfer data between the instrument and the computer via MIDI. For details on using a computer with this instrument, refer to the “Computerrelated Operations” on the website (page 9). NOTICE Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used. NOTE • The instrument will begin transmission a short time after the USB connection is made.
Connections Connecting to an iPhone/iPad (USB [TO DEVICE], USB [TO HOST] and MIDI Terminals) You can connect a smart device such as an iPhone or iPad to this instrument via the USB wireless LAN adaptor UD-WL01 (sold separately; may not be available in some areas). By using appropriate apps on your smart device, you can take advantage of convenient functions and get more enjoyment out of this instrument. • For details on connections, refer to the “iPhone/iPad Connection Manual” on the website (page 9).
Connections The following menu is shown only when you connect the USB wireless LAN adaptor to the USB [TO DEVICE] terminal on this instrument. Menus marked with * differ in the Wireless LAN Mode parameters between the two modes: “Infrastructure” and “Accesspoint.” The default setting for the Wireless LAN Mode is “Infrastructure.” To call up the desired parameter: Press the [FUNCTION] button several times to select “System” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter.
Connections Wireless LAN in the Accesspoint Mode To call up the desired parameter: Press the [FUNCTION] button several times to select “System” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] Utility [>] [<] [>] [<] Default setting Setting range Set the SSID as an access point. ap-[YDP-184]-[xxxxxx (MAC address lower 6 figure)] Up to 32 characters (half size), alphanumeric characters, marks Security Set the Security as an access point.
Connections Displaying the Wireless LAN Networks and connecting to a Network Make sure to connect the USB wireless LAN adaptor (sold separately) to the USB [TO DEVICE] terminal, otherwise the displays for setup below will not be shown. 1. 2. Press the [FUNCTION] button repeatedly to call up the “System” menu display, then select the highlighted item in each display as illustrated below. “System” menu display Utility display Wireless LAN display 1-1. Use the [u]/[d] buttons 1-3.
Connections Automatic Setup by WPS Please make sure to connect the USB wireless LAN adaptor (sold separately) to the USB [TO DEVICE] terminal, otherwise the displays for setup will not be shown. If your access point supports WPS, you can easily connect the instrument to access point by WPS, without making settings, such as password input, etc. Press the WPS button on the USB wireless LAN adaptor more than 3 seconds, and press the WPS button on your access point within two minutes.
Connections 3-2. Select “Security” then press the [>] button to call up the Security list. Select the security then return to the “Other” display by pressing the [<] button. 3-3. Select “Password,” then set the password in the same way as 4. NOTE The password cannot be set when you select “none” for the security setting. SSID. Select “Connect >” at the bottom of the display shown in step 3, then press the [>] button to start connecting.
Connections 2. Set SSID, Security, Password and Channel. 2-1. From the “System” menu display, select the highlighted item in each display as illustrated below. “System” menu display Utility display Wireless LAN display 2-2. Set the SSID, Security, Password and Channel. Select and enter each value/setting in the same way as in step 3 in “Manual Setup.” For the setting range for each item, refer to the table on page 72. 3. Save the setting.
Detailed Settings Pressing the [FUNCTION] button gives you access to a variety of important settings for Voices, Song playback, Metronome, Song recording and the entire system of this instrument. Basic Operations 1. As necessary, make the Voice settings or select a Song. • If you want to edit Voice-related parameters (by calling up the “Voice” menu), select a Voice.
Voice Menu Voice Menu This menu lets you edit or set various parameters related to keyboard performance, such as Voice parameters. By turning on Dual/Split/Duo, you can make the settings for each Voice or each Voice combination. While playing the keyboard and hearing the sound, change a parameter value to find your desired sound. Note that you should turn on Dual/Split/Duo before calling up the “Voice” menu display. NOTE Parameters with * are shown only when Dual/Split/Duo is on.
Voice Menu To call up the desired parameter: Turn on Dual, Split or Duo as necessary, select Voices as necessary, press the [FUNCTION] button several times to select “Voice” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] [>] [<] Voice Edit (Voice names)* [>] [<] Description Default setting Setting range Octave Shifts the pitch of the keyboard up and down in octave steps. This parameter can be set for each Voices when Dual/Split/Duo is on.
Voice Menu To call up the desired parameter: Turn on Dual, Split or Duo as necessary, select Voices as necessary, press the [FUNCTION] button several times to select “Voice” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] [>] [<] [>] [<] Voice Edit (Voice names)* Harmonic Cont Description Default setting Setting range Differs depending -64 – +63 Produces a distinctive “peaky” tone by raising the Resonance value of the Filter.
Voice Menu Reverb Type List Off No effect Recital Hall Simulates clear reverberation in a mid-sized hall suitable for piano recital. Concert Hall Simulates brilliant reverberation in a large hall for public orchestra performances. Chamber Simulates the elegant reverberation in a small room suitable for chamber music. Cathedral Simulates the solemn reverberation in a high-ceiling stone-made cathedral. Club Simulates the lively reverberation in a jazz club or a small bar.
Song Menu Song Menu This menu lets you set various parameters related to Song playback and edit the Song data with a single touch. NOTE • When using the “Edit” menu, select a MIDI Song other than the preset Song. • Execute is a function that edits or changes the current Song data. Note that pressing the [>] button will actually change the Song data.
Song Menu To call up the desired parameter: Select a Song as necessary, press the [FUNCTION] button several times to select “Song” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] Edit [>] [<] Quantize [>] [<] Quantize Strength Description The Quantize function allows you to align all the notes in the current MIDI Song to the correct timing, such as 8th note or 16th note. 1. Set the Quantize value to the smallest notes in the MIDI Song.
Song Menu Quantize Supplementary Quantize setting range 1/4................ quarter note 1/6................ quarter note triplet 1/8................ eighth note 1/12.............. eighth note triplet 1/16.............. sixteenth note 1/24.............. sixteenth note triplet 1/32.............. thirty-second note 1/8+1/12....... eighth note + eighth note triplet* 1/16+1/12..... sixteenth note + eighth note triplet* 1/16+1/24.....
Metronome/Rhythm Menu Metronome/Rhythm Menu This menu lets you set the volume and tempo indication format of the Metronome (page 33) or Rhythm (page 48). In addition, you can set the bell sound of the Metronome to play back at the first beat and adjust parameters related to Rhythm playback variation. To call up the desired parameter: Press the [FUNCTION] button several times to select “Metronome/Rhythm” menu, then use the [u]/[d] buttons to select the desired parameter.
Recording Menu Recording Menu This menu lets you make detailed settings related to MIDI Recording (page 49). To call up the desired parameter: Press the [FUNCTION] button several times to select “Recording” menu, then use the [u]/[d] buttons to select the desired parameter. [>] [<] 86 [>] [<] [>] [<] RecStart – – This parameter, which is used when you overwrite the already recorded MIDI Song, determines when the actual MIDI Recording starts after you execute the Recording Start operation.
System Menu System Menu This menu lets you make the overall settings applied to the entire instrument. To call up the desired parameter: Press the [FUNCTION] button several times to select “System” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] Tuning [>] [<] Master Tune [>] [<] (Pop-up window) Description Fine tunes the pitch of the entire instrument. This function is useful when you play this instrument along with other instruments or CD music.
System Menu To call up the desired parameter: Press the [FUNCTION] button several times to select “System” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] Pedal [>] [<] [>] [<] Description Default setting Half Pedal Point (Pop-up window) Here you can specify the point to which you must depress the right pedal before the assigned effect begins to be applied. This setting applies only to the “Sustain Continuously” effect is assigned.
System Menu To call up the desired parameter: Press the [FUNCTION] button several times to select “System” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] MIDI [>] [<] [>] [<] Local Control Receive Param. – Description “Local Control On” is a state in which this instrument produces the sound from its tone generator when you play the keyboard. In “Local Control Off” state, the keyboard and the tone generator are cut off from each other.
System Menu To call up the desired parameter: Press the [FUNCTION] button several times to select “System” menu, then use the [u]/[d]/[<]/[>] buttons to select the desired parameter. [>] [<] Utility [>] [<] [>] [<] USB Properties – Description Default setting Setting range Shows the amount of free space and entire memory in the USB flash drive connected to the USB [TO DEVICE] terminal.
System Menu Scale Tune List (Temperament List) Equal Temperament One octave is divided into twelve equal intervals. Currently most popular piano tuning scale. PureMajor/PureMinor Based on natural overtones, three major chords using these scales produce a beautiful, pure sound. Pythagorean This scale was devised by Pythagoras, the famous Greek philosopher and is created from a series of perfect fifths, which are collapsed into a single octave.
System Menu Backup Setting Backup (Selecting parameters maintained even when the power is turned off) (Saving the Backup file for internal data) This lets you set whether some settings of the Backup Setting (below) are maintained or not when the power is turned off. The Backup Setting consists of two groups, “Voice” (including Voice related settings such as Voice selection) and “Other” (including various settings such as Song Repeat and Tuning), which can be set individually.
System Menu Restore Factory Set (Restarting the instrument with the Backup file loaded) (Restarting the instrument with the initial factory settings loaded) This lets you load the backup file (ydp-184.bup) saved via the Backup function (page 92) to the instrument on. NOTICE • It may take 1 – 2 minutes to complete this operation. Never turn off the power during this operation (while “Executing” is shown). Doing so could result in damage to the data.
Appendix Preset Voice List Voice Group Piano E.Piano Organ Strings Bass Others Stereo Sampling Touch Sense Key-off Sampling VRM Voice Demo CFX Grand (1) Pop Grand — A slightly brighter piano sound. Good for popular styles. Jazz Grand — — A piano sound with unique tonal character. Good for jazz styles. Rock Grand — A bright-sounding piano. Ideal for rock styles. HonkyTonk Pf — — A honky-tonk style piano.
Preset Voice List Voice group Voice name Title Composer (1) Piano CFX Grand (2) Organ Organ Principal Herr Christ, der ein'ge Gottes-Sohn, BWV 601 J. S. Bach (3) Others Harpsichord 8' Concerto a cembalo obbligato, 2 violini, viola e continuo No.7, BWV 1058 J. S. Bach Impromptu No.1 op.29 F. F. Chopin The Voice Demos with () listed above are short rearranged excerpts of the original compositions. All other Demo Songs are Yamaha original (© Yamaha Corporation).
Song List 50 Classics No. Song Title Composer Arrangements 1 Canon D dur 2 Air On the G Strings J. Pachelbel J. S. Bach 3 Jesus, Joy of Man’s Desiring J. S. Bach 4 Twinkle, Twinkle, Little Star Traditional 5 Piano Sonate op.31-2 “Tempest” 3rd mov. L. v. Beethoven 6 Ode to Joy L. v. Beethoven 7 Wiegenlied op.98-2 F. P. Schubert 8 Grande Valse Brillante F. F. Chopin 9 Polonaise op.53 “Héroïque” F. F. Chopin 10 La Campanella F. Liszt 11 Salut d’amour op.12 E.
Rhythm List Category Pops&Rock Jazz Latin Kids&Holiday No.
Message List Some message display remains open. In this case, press the [EXIT] button to close message display. Message 98 Meaning Access error The operation has failed. The following causes can be considered. If the following are not responsible, the file may be damaged. • The file operation is wrong. Follow the instructions in “Handling Song Files” (page 60) or “Backup”/ “Restore” (pages 92 – 93). • The connected USB flash drive is not compatible with this instrument.
Message List Message Meaning Protected Song You attempted a file operation to a Protected Song or read-only file. Data of those types have handling limitations (page 60), and also cannot be used for editing (page 56). Use a read-only file after cancelling the read-only setting. Remaining space on drive is low Since the remaining space on the “User”/USB flash drive is low, delete any unnecessary files (page 62) before recording.
Troubleshooting When a message is displayed, refer to the “Message List” (page 98) for troubleshooting aid. Problem Possible Cause and Solution The instrument does not turn on. The instrument has not been plugged in properly. Securely insert the female plug into the socket on the instrument, and the male plug into a proper AC outlet (page 14). A click or pop is heard when the power is turned on or off. This is normal when electrical current is being applied to the instrument.
Troubleshooting Problem Possible Cause and Solution Rhythm does not start. “SynchStart” setting is on. Set “SynchStart” off in the “Metronome/Rhythm” menu display. The contents of the Wireless LAN is not shown in the display even though the USB wireless LAN adaptor is connected. Disconnect the USB wireless LAN adaptor and connect it again. Sound input via the [AUX IN] jack is interrupted. The Noise Gate function of this instrument cuts unwanted noise from the input sound.
Keyboard Stand Assembly Assembly Precautions CAUTION • Assemble the unit on a hard and flat floor with ample space. • Be careful not to confuse parts, and be sure to install all parts in the correct orientation. Please assemble the unit in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use only the included screws of the specified sizes. Do not use any other screws. Use of incorrect screws can cause damage or malfunction of the product.
Keyboard Stand Assembly Remove all parts from the package and make sure you have all of the items. 1. Attach C to D and E. 1-2 E C 1-2 Foamed styrol pads Remove foamed styrol pads from the package, position them on the floor, then place A on top of them. Position the pads so that they will not hide the connectors on the bottom of A. D 1-2 1-1 Bundled pedal cord inside 1-1. Untie and straighten out the bundled pedal cord. Do not discard the vinyl tie. You will need it later in step 5. 1-2.
Keyboard Stand Assembly 2-1. Align the screw holes on the upper side of B with the bracket holes on D and E, then attach the upper corners of B to D and E by fingertightening two thin screws (4 × 12 mm). 4. Secure A. 4-1 2-2. Secure the bottom end of B using four A tapping screws (4 × 20 mm). 2-3. Securely tighten the screws on the top of B that were attached in step 2-1. 3. A Mount A. Be sure to place your hands at least 15 cm away from either end of the main unit when positioning it.
Keyboard Stand Assembly 5-1. Insert the plug of the pedal cord into the Attach the headphone hanger. Use the two thin screws (4 × 10 mm) to attach the hanger as shown in the illustration. PE DA L pedal connector. Insert the pedal cord securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly. 7. 5-2. Attach the cord holders to the rear panel as shown, then clip the cord into the holders. 5-3.
Specifications Items YDP-184 Product Name Size/Weight Digital Piano Width Height Control Interface 1461 mm (57-1/2") With music rest closed 927 mm (36-1/2") With music rest raised 1081 mm (42-9/16") Depth 459 mm (18-1/16") Weight 56.0 kg (123 lbs., 7 oz.
Specifications Items Functions YDP-184 Rhythms Preset 20 Overall Controls Metronome Yes Tempo Range Transpose Tuning Scale Type Piano Room Storage and Connectivity Storage Connectivity 414.8 – 440.0 – 466.8 Hz (approx. 0.2Hz increments) 7 types Yes Internal Memory Total maximum size approx. 1.
Index Numerics F 50 Classics .................................................................. 38, 96 Factory Set .........................................................................93 Fast forward ......................................................................40 File Operation ...................................................................60 Format (instrument) .......................................................93 Format (USB flash drive) ............................................
Index P Part Cancel ........................................................................41 Pedal ............................................................................ 19, 88 Pedal Function List ..........................................................81 Piano Room ......................................................................24 Piano Setting .....................................................................78 Pitch Bend ................................................................
Yamaha Global Site https://www.yamaha.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Group © 2017 Yamaha Corporation Published 05/2017 MWZC*.