A RX-V465 AV Receiver OWNER’S MANUAL
Caution: Read this before operating your unit. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.
Contents INTRODUCTION Front panel ................................................................. 4 Rear panel .................................................................. 5 Front panel display..................................................... 6 Remote control........................................................... 7 Quick start guide..................................................... 8 L Preparing remote control .......................................
INTRODUCTION Features ■ Built-in 5-channel power amplifier • Minimum RMS output power (1 kHz, 0.
About this manual Bluetooth™ Bluetooth is a registered trademark of Bluetooth SIG and is used by Yamaha in accordance with a license agreement. PREPARATION Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories. “HDMI,” the “HDMI” logo and “High-Definition Multimedia Interface” are trademarks, or registered trademarks of HDMI Licensing LLC. x.v.Color™ “x.v.Color” is a trademark of Sony Corporation.
Part names and functions Front panel U T D E F G H P VOLUME HDMI THROUGH INFO l MEMORY PRESET h l AM FM TUNING h SCENE BD/DVD PHONES TONE CONTROL PROGRAM l STANDBY /ON A CD STRAIGHT DIRECT B C J K STANDBY/ON LM M PHONES jack INFO MEMORY N PRESET l / h O FM G AM H TUNING l / h Sets the FM/AM tuner band to FM (see page 28). P Q Switches between linked sets of input sources and sound field programs (see page 21).
Part names and functions Rear panel c b d l k INTRODUCTION a (BD/DVD) DOCK HDMI 2 HDMI 1 HDMI OUT HDMI 3 ANTENNA HDMI 4 CENTER UNBAL.
Part names and functions Front panel display a b c d SLEEP STEREO TUNED f e VOL. MUTE SW C L R SL SR SBL SB SBR g a h HDMI indicator Lights up during normal communication when HDMI is selected as an input source. b CINEMA DSP indicator Lights up when a sound field program that uses CINEMA DSP is selected. c Tuner indicator Lights up while receiving a radio broadcast signal from an FM/ AM station (see page 28).
Part names and functions Remote control g b HDMI 1-4 AV 1-6 AUDIO 1/2 V-AUX CODE SET TRANSMIT c d POWER SOURCE POWER SLEEP e HDMI 1 2 1 2 3 4 3 4 Input selection keys f [A]/[B] AV 5 6 1 2 V-AUX [ A ] [ B ] DOCK DOCK TUNER TUNER h h FM AM PRESET i MEMORY MOVIE MUSIC FM AM MEMORY PRESET k / n TUNING k / n ENHANCER SUR. DECODE j STEREO STRAIGHT DIRECT i SCENE k l BD DVD TV CD SETUP Tuner keys Presets radio stations. Selects a preset station.
Quick start guide When you use this product for the first time, perform setup following the steps below. See the related pages for details on operations and settings. Step 1: Prepare items for setup Step 2: Set up your speakers Prepare speakers, DVD player, cables, and other items necessary for setup. For example, prepare the following items for setting up a 5.1-channel sound system. Front right speaker Place your speakers in the room and connect them to this unit.
PREPARATION Preparing remote control 1 Using the remote control The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. 3 Remote control sensor window PREPARATION 2 30 2 Insert the two supplied batteries (AAA, R03, UM-4) according to the polarity markings (+ and –) on the inside of the battery compartment. Snap the battery compartment cover back into place.
Connections Placing speakers This unit supports up to 7.1-channel surround. We recommended the following speaker layout in order to obtain the optimum surround effect. 7.1-channel speaker layout Speaker channels C FR FL SW SW 30˚ SL SR 60˚ 80˚ SL SR SBL SBR 30 cm (12 in) or more 6.1-channel speaker layout C FR FL SW SW 30˚ ■ Front left and right speakers (FL and FR) The front speakers are used for the front channel sounds (stereo sound) and effect sounds.
Connections Connecting speakers When you connect speakers, connect them to the respective terminals as follows, according to your speaker layout. b a DMI 3 HDMI 4 SPEAKERS FRONT CENTER SURROUND Surround Back L/R speakers BASIC OPERATION External Amplifier SURROUND BACK AUDIO OUT SUBWOOFER PRE OUT d f ADVANCED OPERATION e ■ SURROUND BACK L (white) SURRUND BACK R (red) 5.
Connections Connecting the speaker cable Caution • A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this unit and the other end to that of your speaker.
Connections Information on jacks and cable plugs ■ ■ Audio jacks Jack and cables AUDIO jacks (white) L Description R (red) To transmit coaxial digital audio signals. Use pin cables for digital audio signals. (orange) C O To transmit optical digital audio signals. Use optical fiber cables for optical digital audio signals. OPTICAL HDMI • We recommend that you use a commercially available 19-pin HDMI cable no longer than 5 meters (16 feet) with the HDMI logo printed on it.
Connections Connecting a TV monitor or projector Connect a video monitor such as a TV or projector to an output terminal of this unit. You can select one of the following three types according to the input signal format supported by the video monitor. Note • When you connect this unit to the video monitor, make sure that this unit is on standby.
Connections Connecting other components Note • When you connect this unit to the external components, make sure that this unit is on standby. Audio / video input (AV 1-6) Audio / video output (AV OUT) PREPARATION HDMI input (HDMI 1-4) (BD/DVD) DOCK HDMI 2 HDMI 1 HDMI OUT HDMI 3 ANTENNA HDMI 4 FRONT COMPONENT VIDEO COMPONENT VIDEO CE UNBAL. PR PR GND AM FM PB PB VIDEO VIDEO Y INTRODUCTION This unit has input and output terminals for respective input and output sources.
Connections ■ Audio player Output jacks on the connected external component Input sources/jacks of this unit External components Output jacks External component with optical digital output Optical digital output External component with coaxial digital output Coaxial digital output External component with analog audio output Analog audio output AV 1 (TV) OPTICAL AV 4 OPTICAL AV 2 COAXIAL AV 3 (CD) COAXIAL AV 5 AUDIO AV 6 AUDIO AUDIO 1 AUDIO AUDIO 2 AUDIO y • We recommend connecting
Connections Connecting the FM and AM antennas Indoor FM antenna AM loop antenna (BD/DVD) DOCK HDMI 2 HDMI 1 HDMI OUT HDMI 3 ANTENNA F COMPONENT VIDEO COMPONENT VIDEO Select the switch position according to your local voltage using a straight slot screwdriver. UNBAL. PR PR FM PB GND AM Caution The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet.
Optimizing the speaker setting for your listening room (YPAO) This unit has a Yamaha Parametric Acoustic Optimizer (YPAO). With the YPAO, this unit automatically adjusts the output characteristics of your speakers based on speaker position, speaker performance, and the acoustic characteristics of the room. We recommend that you first adjust the output characteristics with the YPAO when you use this unit. Notes • Be advised that it is normal for loud test tones to be output during the “Auto Setup” procedure.
Optimizing the speaker setting for your listening room (YPAO) 4 >Set Cancel 7 To cancel the operation, press nCursor l / h to select “Cancel” and press nENTER. When “Disconnect MIC” appears, remove the optimizer microphone. Auto Setup is complete. The optimizer microphone is sensitive to heat. Store it in a cool place and away from direct sunlight after measurement. Do not leave it in a place where it will be subjected to high temperatures such on an AV component.
Optimizing the speaker setting for your listening room (YPAO) When an error message is displayed during measurement Press nCursor n once, and select “Retry” or “Exit” using nCursor l / h and then press nENTER. When a warning message is displayed after measurement If a problem occurs during measurement, “W-xx” (xx indicates the number) is displayed on the front panel display. Check the error and solve the problems. Retry Performs “Auto Setup” again. Exit Terminates the measurement and “Auto Setup.
BASIC OPERATION Playback Using the SCENE function Turn on external components (TV, DVD player, etc.) connected to this unit. 2 Press NINPUT l / h (or gInput selection keys) to select an input source. The name of the selected input source is displayed for a few seconds. Input source name VOL. AV1 This unit has a SCENE function that allows you to change input sources and sound field programs with one key. Four scenes are available for different usages, such as playing movies or music.
Playback 2 Press gInput selection keys on the remote control for the input source whose remote control code was registered in step 1 for about 3 seconds while pressing down kSCENE key whose assignment you want to change. The external component can now be controlled remotely just by selecting a scene. Muting audio output temporarily (MUTE) 1 2 Press qMUTE on the remote control to mute the audio output. The MUTE indicator on the front panel display flashes while audio output is muted.
Playback Displaying input signal information Select the desired input source, and press mOPTION. The option menu for the selected input source is displayed (see page 33). 2 Press nCursor k / n to select “Signal Info,” and press nENTER. Information on input signals is displayed. See page 34 on messages displayed on the front panel display. 3 Press nCursor k / n to select the desired item. Note • If an HDMI related error occurs, press nCursor to display an error message.
Enjoy the sound field programs This unit is also equipped with a Yamaha digital sound field processing (DSP) chip. You can enjoy multi-channel sounds for almost all input sources using various sound field programs stored on the chip and a variety of surround decoders. Selecting sound field programs ■ Selecting a sound field program on the front panel Press KPROGRAM l / h repeatedly to select a desired sound field program.
Enjoy the sound field programs Program Descriptions This program is provided for reproducing monaural video sources such as a classic movie in an atmosphere of a good old movie theater. The program produces the optimum expansion and reverberation to the original audio to create a comfortable space with a certain sound depth. Sports This program allows the listeners to enjoy stereo sport broadcasts and studio variety programs with enriched live feeling.
Enjoy the sound field programs For Multi-channel stereo reproduction Program 7ch Stereo Descriptions Use this program to output sound from all speakers. When you play back multi-channel sources, this unit downmixes the source to 2 channels, and then outputs the sound from all speakers. This program creates a larger sound field and is ideal for background music at parties, etc.
Enjoy the sound field programs Enjoying unprocessed input sources (Straight decoding mode) To enable straight decoding mode, press LSTRAIGHT (or jSTRAIGHT). “Straight” appears on the front panel display. 2 To cancel straight decoding mode, press LSTRAIGHT (or jSTRAIGHT) again. A sound field program name appears on the front panel display, and sound is reproduced with that sound field effect. Note • SILENT CINEMA mode is not available in the following conditions.
FM/AM tuning The FM/AM tuner of this unit provides the following two modes for tuning. ■ Frequency tuning mode (Auto tuning / Manual tuning) You can tune in to a desired FM/AM station by searching or specifying its frequency. ■ Preset tuning mode (Preset tuning) You can preset the frequencies of FM/AM stations by registering them to specific numbers, and later just select those numbers to tune in. When you press and release the key The tuner increases or decreases the frequency in steps.
FM/AM tuning y • You can select the preset number at which the preset starts by pressing hPRESET k / n or nCursor k / n while the front panel display is in the state as shown in the below figure. • To cancel registration, press nRETURN on the remote control. 4 y • To cancel registration, press nRETURN on the remote control or leave the tuner without any operations for about 30 seconds. 01:FM 87.
Using iPod™ Once you have stationed your iPod in a Yamaha iPod universal dock (such as the YDS-11, sold separately) connected to the DOCK terminal on the rear panel of this unit (see page 16), you can enjoy playback of your iPod using the supplied remote control. You can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts (such as MP3 format) stored on your iPod (see page 24).
Using iPod™ Shuffle/repeat playback 2 Press mOPTION. The option menu is displayed. 3 Press nCursor k / n to select the desired playback function, Shuffle or Repeat, then press nENTER. The following playback styles are available depending on the playback function selected. BASIC OPERATION Press pDISPLAY to switch to menu browse mode while “DOCK” is selected as the input source. The option menu can be displayed only in menu browse mode.
Using Bluetooth™ components You can connect a Yamaha Bluetooth wireless audio receiver (such as YBA-10, sold separately) to the DOCK terminal of this unit and enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between this unit and the Bluetooth component. You need to perform “Pairing” the connected Bluetooth wireless audio receiver and your Bluetooth component in advance.
ADVANCED OPERATION Setting the option menu for each input source (OPTION menu) Select an input source using NINPUT l / h (or gInput selection keys). 2 Press mOPTION on the remote control. The OPTION menu appears. The displayed OPTION menu items differ depending on the input source. For details, see the following section.
Setting the option menu for each input source (OPTION menu) ■ Decoder Mode Input source: HDMI1-4, AV1-4 Choices: Auto*/DTS Selects DTS digital audio signals for reproduction. Auto DTS ■ Automatically selects audio input signals. Selects DTS signals only. Other input signals are not reproduced. EXTD Surround Signal Info Input source: HDMI1-4, AV1-4 Displays information on audio and video signals on the front panel display. You can change items to be displayed using nCursor k / n.
Setting the option menu for each input source (OPTION menu) ■ Auto Preset Input source: TUNER ■ INTRODUCTION Automatically detects radio stations in the FM frequency band and registers them as preset stations (see page 28). Clear Preset Input source: TUNER Clears the preset stations (see page 29). ■ Shuffle Input source: iPod (DOCK) Choices: Off*/Songs/Albums ■ PREPARATION Changes the shuffle playback style (see page 31).
Editing surround decoders/sound field programs Selecting a decoder used with a sound field program When using sound field programs for movies or TV programs, you can select a surround decoder to be used with the sound field program after setting the parameters from the following decoders. To set the parameters for sound field programs, see the following section.
Editing surround decoders/sound field programs ■ Straight Enhancer/7ch Enhancer only EFCT LVL Choices: High*/Low INTRODUCTION Adjusts the Compressed Music Enhancer effect level. When the high-frequency signals of the source is emphasized too much, set the effect level to “Low.” To reduce the effect, set this parameter to “Low.” To increase the effect, set it to “High.” Decoder parameters ■ PREPARATION You can customize decoder effects by setting the following parameters.
Operating various settings for this unit (Setup menu) You can call the setup menu using the remote control and change the settings of various menus. You can change the following settings in the setup menu. For details, read “Basic operation of the setup menu” first, and see the respective pages. Menu/Submenu Speaker Setup Function Page Sets items for speakers. 39 1 Auto Setup (YPAO) Automatically adjusts output characteristics of speakers.
Operating various settings for this unit (Setup menu) Basic operation of the setup menu Press lSETUP on the remote control. The setup menu screen appears. 2 Select a menu using nCursor k / n, and press nENTER. Items of the selected menu are displayed. For example, the following screen appears when you select “Function Setup.” y • You can return to the previous screen by pressing nRETURN. 3 Dimmer;;;;;;;0 Select an item using nCursor k / n, and change the setting of the item using nCursor l / h.
Operating various settings for this unit (Setup menu) Low-frequency components of other channel signals Parameter Front speakers Subwoofer Other speakers Both [1] [2] [3] SWFR [4] [3] [3] Front Not output [1] [3] [1] [2] [3] [4] Outputs low-frequency components of the front left and right channels and the channel of speaker, the size of which is set to “Small.” Outputs low-frequency components of the front left and right channels.
Operating various settings for this unit (Setup menu) ■ B)Level GEQ Adjustable range: -10.0dB to +10.0dB (0.5 dB step) Defaults: “FL/FR/SWFR” 0dB* “C/SL/SR/SBL/SBR” -1.0dB 63Hz/160Hz/400Hz/1kHz/2.5kHz/ 6.3kHz/16kHz Adjustable range: -6.0dB to 0dB* to +6.0dB (0.5 dB step) Separately adjusts volume of each speaker so that the sounds form speakers are at the same volume at the listening position. Items to be displayed vary depending on the number of speakers connected.
Operating various settings for this unit (Setup menu) Auto Adjustable range: 0 to 240ms (1 ms step) Enables manual fine adjustment of the correction time when “HDMI Auto” is set to “On.” Manual 2 Display You can set items for the front panel display. ■ Dimmer Adjustable range: -4 to 0* Adjustable range: 0* to 240ms (1 ms step) Manually adjusts the correction time. Select this when the connected monitor does not support the automatic lip-sync function or you set “HDMI Auto” to “Off.
Operating various settings for this unit (Setup menu) ■ MaxVol Adjustable range: -30.0dB to +15.0dB/+16.5dB* (5.0 dB step) ■ IniVol Choices: Off*/Mute/-80.0dB to +16.5dB (0.5 dB step) Memory Guard Choices: Off*/On Protects settings of setup menu against accidental alteration. Off On Not protect settings. Protects the settings of the setup menu (except for the Memory Guard setting). Note • If the setting of “MaxVol” is lower than the setting of “IniVol,” the setting of “MaxVol” becomes effective.
Controlling other components with the remote control You can control external components for a selected input source with the remote control. The keys available for controlling external components are as follows: dSOURCE POWER Turns on and off an external component. Input source nCursor, ENTER, RETURN Operates the menus of external components. pDISPLAY Switches between the screens of external components.
Advanced setup Set this unit to the standby mode. 2 Press ASTANDBY/ON while pressing and holding LSTRAIGHT on the front panel. The advanced setup menu appears on the front panel display. Two IDs are provided for the remote control of this unit. If another Yamaha amplifier is in the same room, setting a different remote control ID to this unit prevents unwanted operation of the other amplifier. ID1 is set for both remote control and amplifier by default.
APPENDIX Troubleshooting Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. General Problem Cause Remedy See page This unit fails to turn on or enters the standby mode soon after the power is turned on.
Troubleshooting Problem Remedy See page — The sleep timer has turned off this unit. Turn on this unit, and play the source again. — Sound is heard from the speaker on one side only. The playback component or speakers are not connected properly. Connect the cables properly. If the problem persists, the cables may be defective. 11 The speaker level settings are incorrect. Adjust “B)Level” settings. 41 Only the center speaker outputs substantial sound.
Troubleshooting Problem Cause Remedy See page The audio input sources cannot be played in the desired digital audio signal format. The connected component is not set to output the desired digital audio signals. Set the playback component properly referring to its operating instructions. — Noise/hum noise is heard. Incorrect cable connection. Connect the audio cables properly. If the problem persists, the cables may be defective. — A DTS-CD is being played back.
Troubleshooting Tuner (FM/AM) FM stereo reception is noisy. See page Check the antenna connections. 17 Replace the outdoor antenna with a more sensitive multi-element antenna. — Switch to monaural mode. 34 There is multi-path interference. Adjust the antenna height or orientation, or place it in a different location. — The desired station cannot be tuned into with the automatic tuning method. You are in an area far from a station or an input from the antenna is weak.
Troubleshooting Remote control Problem The remote control does not work or function properly. Cause Remedy See page Wrong distance or angle. The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. 9 Direct sunlight or lighting (from an inverter type of fluorescent lamp, strobe light, etc.) is striking the remote control sensor of this unit. Adjust the lighting angle or reposition this unit. — The batteries are weak.
Troubleshooting Problem Unable to play Cause See page Check that the songs currently stored on your iPod are playable. — Store some other playable music files on your iPod. — Bluetooth™ Problem Remedy See page PREPARATION Searching... Cause The Bluetooth wireless audio receiver and the Bluetooth component are in the middle of the pairing. The Bluetooth wireless audio receiver and the Bluetooth component are in the middle of establishing the connection. Canceled The pairing is canceled.
Troubleshooting Error message E-5:NOISY Cause Remedy See page Measurement cannot be performed accurately due to loud ambient noise. Try running “Auto Setup” in a quiet environment. — Turn off noisy electric equipment like air conditioners or move them away from the optimizer microphone. — E-6:CHECK SUR. Surround back speakers are connected, though surround L/R speakers are not. When using surround back speakers, you need to connect surround L/R speakers.
Glossary ■ Audio and video synchronization (lip sync) ■ Dolby Digital Surround EX Dolby Digital EX creates 6 full-bandwidth output channels from 5.1channel sources. For the best results, Dolby Digital EX should be used with movie sound tracks recorded with Dolby Digital Surround EX. With this additional channel, you can experience more dynamic and realistic moving sound especially with scenes with “fly-over” and “flyaround” effects.
Glossary ■ DSD Direct Stream Digital (DSD) technology stores audio signals on digital storage media, such as Super Audio CDs. Using DSD, signals are stored as single bit values at a high-frequency sampling rate of 2.8224 MHz, while noise shaping and oversampling are used to reduce distortion, a common occurrence with very high quantization of audio signals. Due to the high sampling rate, better audio quality can be achieved than that offered by the PCM format used for normal audio CDs.
Sound field program information ■ ■ CINEMA DSP SILENT CINEMA Yamaha has developed a natural, realistic sound effect DSP algorithm for headphones. Parameters for headphones have been set for each sound field so that accurate representations of all the sound field programs can be enjoyed on headphones. ■ Compressed Music Enhancer The Compressed Music Enhancer feature of this unit enhances your listening experience by regenerating the missing harmonics in a compression artifact.
Additional information About the HDMI control function This unit supports the HDMI control function. When a TV that supports the HDMI control function is connected with this unit via the HDMI connection, the following operations of this unit can be controlled with the TV remote control (except for some TVs). • Switching between on and standby (linked to the TV) • Volume control (up/down, mute) • Switching the sound output between a TV and this unit.
Specifications AUDIO SECTION • Video Signal Type (Gray Back) [U.S.A., Canada, Korea and General models] ...................... NTSC [Other models] ......................................................................... PAL • Signal Level Composite ...................................................................1 Vp-p/75 Ω Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (CB/CR) • Maximum Input Level............................................ 1.
Index ■ Numerics 1 Dynamic Range, sound setup ..................... 41 1 HDMI, function setup ................................. 42 2 Display, function setup ............................... 42 2 Lipsync, sound setup .................................. 41 2ch Stereo, sound field program .................... 25 3 Volume, function setup .............................. 42 4 Input Rename, function setup ..................... 43 5.1-channel speaker layout ............................ 10 6.
Index U Using the remote control ................................. 9 ■ V VIDEO jack ................................................... 13 Video jack ...................................................... 13 VIDEO jack, front panel .................................. 4 Video/audio jack ............................................ 13 Virtual CINEMA DSP ................................... 27 VOLTAGE SELECTOR ............................... 17 VOLTAGE SELECTOR, rear panel ...............
List of remote control codes TV A.R.
Fujitsu Siemens 0425, 0426, 0427, 0428, 0429 Funai 0033, 0034, 0035, 0036, 0037, 0097, 0104, 0105, 0225, 0259 Futuretech 0104, 0225 Galaxi 0269, 0274 Galaxis 0243, 0274 Gateway 0163, 0226, 0227 GBC 0261, 0266, 0273 GE 0069, 0071, 0072, 0073, 0077, 0090, 0099, 0102, 0106, 0112, 0131 Geant Casino 0275 GEC 0260, 0265, 0268, 0271, 0274, 0328 Geloso 0261, 0264, 0273 General Technic 0261, 0273 Genexxa 0262, 0265, 0268, 0274 GFM 0177, 0210 Giant 0328 Gibralter 0076, 0090, 0096, 0108 GoldHand 0327 Goldline 0274 Gol
Neckermann NEI Net-TV Neufunk New Tech New World NewTech Nicamagic Nikkai Nikko Nobliko Nokia Norcent Nordic Nordmende Nordvision Novatronic Oceanic Okano Olevia ONCEAS Onwa Opera Oppo Optimus Optoma Optonica Orbit Orion Orline Osaki Oso Otto Versand Pael Palladium Palsonic Panama Panasonic Panavision Pathe Cinema Pausa Penney Perdio Perfekt Philco Philharmonic Philips iii 0243, 0257, 0260, 0264, 0268, 0269, 0271, 0274, 0328 0268, 0271, 0274 0226 0273, 0274 0261, 0268 0262 0273, 0274, 0328 0260, 03
Sylvania Symphonic Syntax Syntax-Brillian Sysline Sytong Tandy Tashiko Tatung TCM Teac Tec Technics TechniSat Techwood TEDELEX Teknika Teleavia Telecor Telefunken Telegazi Telemeister Telesonic Telestar Teletech Teleton Televideon Televiso Tensai Tesmet Tevion Texet Thomson Thorn TMK TNCi Tokai Tokyo Tomashi Toshiba Totevision Towada Trakton Trans Continens Transtec Trident 0072, 0088, 0089, 0090, 0091, 0095, 0096, 0097, 0098, 0175, 0177, 0210 0097, 0104, 0108, 0133, 0210, 0225 0149 0149 0271 0327 022
iBUYPOWER Impego Imperial Inno Hit 1066 1076 1072 1075, 1076, 1078, 1079, 1090, 1091 Innovation 1074 Instant Replay 1022 Interbuy 1077, 1090 Interfunk 1078 Intervision 1072, 1091 Irradio 1077, 1079, 1090 ITT 1073 ITV 1075, 1077, 1091 JC Penney 1018, 1019, 1020, 1021, 1022 JCL 1022 JVC 1011, 1012, 1013, 1014, 1015, 1016, 1017, 1018, 1019, 1028, 1035, 1064, 1073, 1085, 1117, 1130, 1131, 1133, 1134, 1135, 1136 Kaisui 1079, 1090 Karcher 1078 Kendo 1074, 1075, 1076, 1090 Kenwood 1018, 1019, 1073 Kodak 1021, 102
ATACOM Audiovox Avious Awa Axion Bang & Olufsen Baze BBK Bellagio Best Buy Blaupunkt Blue Parade Boghe Brainwave Brandt Broksonic Bush 2318 2111, 2199 2317 2313 2171 2210 2317 2318 2313 2309 2209 2207 2300 2312 2198, 2238 2192, 2195 2018, 2060, 2248, 2264, 2301, 2308, 2317, 2350, 2368 California Audio Labs 2197 Cambridge Audio 2304 CAT 2306, 2307 CAVS 2146 Centrum 2307 CGV 2304, 2312 Changhong 2222 Cinetec 2313 CineVision 2191, 2215 Clatronic 2308, 2317 Coby 2077, 2124, 2314 Conia 2301 Continental Edison 2
Skyworth Slim Art SM Electronic Sonic Blue Sontech Sony 2310 2312 2305 2215 2316 2005, 2006, 2007, 2020, 2021, 2022, 2023, 2024, 2025, 2069, 2072, 2073, 2085, 2086, 2087, 2091, 2092, 2093, 2102, 2128, 2129, 2130, 2249, 2250, 2323, 2334, 2335, 2336, 2360, 2361, 2362, 2363, 2364, 2365, 2384 Soundmaster 2305 Soundmax 2305 Spectra 2313 Spectroniq 2155 Standard 2305 Star Cluster 2305 Starmedia 2308, 2318 Sungale 2158 Sunkai 2312 Superscan 2196 Supervision 2305 Sylvania 2094, 2180, 2189, 2196, 2219, 2224 Symphon
Viewmaster Vision Visiopass Vortex View Wittenberg Zenith Zentek 3045 3045 3051, 3054, 3055 3045 3048 3035, 3040, 3046 3044 Sattelite AB Sat AccessHD ADB AGS Akai Alba 4138, 4139 4058 4142 4138 4101, 4103 4083, 4084, 4085, 4086, 4108, 4139 Aldes 4085, 4087, 4088 Allsat 4098, 4101, 4103 Allsonic 4074, 4087, 4090 Alltech 4139 Alpha 4103 Alpha Digital 4058 Alphastar 4031 Amitronica 4139 Amstrad 4089, 4113, 4136, 4139 Anglo 4139 Ankaro 4074, 4087, 4090, 4139 Anttron 4083, 4086 Apollo 4083 Armstrong 4089, 410
Orbitech OSat Otto Versand Pace Pacific Packsat Palcom Palladium Palsat Panasat Panasonic Panda Pansat Patriot Paysat PCT Philco Philips Phoenix Phonotrend Pioneer Polsat Predki Premiere Priesner Primestar Profile Promax Prosat Proscan Protek Proton Provision Quadral Quelle Quiero RadioShack Radiola Radix Rainbow RCA Realistic Redpoint Redstar RFT Roadstar Roch Rover Saba Sabre Sagem Sakura Samsung SAT Sat Cruiser Sat Partner Sat Team ix 4083, 4134, 4135, 4136 4086 4093 4084, 4093, 4113, 4121, 4125, 4
© 2009 Yamaha Corporation All rights reserved.
Printed in China NS-6900/7900/P7900-G SUPPLIED ACCESSORIES OWNER’S MANUAL PLACING THE SPEAKER G NS-6900/NS-7900/NS-P7900 ■ Attaching the stand to the front speaker Front speaker (NS-6900/NS-7900) Notes • Do not place the speaker on top of the TV which area is smaller than the bottom area of the speaker. If placed, the speaker may drop out causing an injury to you. • Do not place the speaker on top of the TV with an inclination.
NS-6900/7900/P7900CONNECTING TO YOUR AMPLIFIER Always turn off your amplifier before making any connections. REMOVING THE FRONT COVER OF THE FRONT SPEAKER ■ Connections ■ Before connecting Remove the insulation coating at extremity of each speaker cable by twisting the coating off. Note: • Do not let uninsulated bare wires touch each other as this could damage the speaker or the amplifier. • Securely twist the bare wires and lump them together to prevent them causing a short circuit.
UB YST-SW216 Subwoofer System OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
FCC INFORMATION (for US customers) We Want You Listening For A Lifetime 1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used.
Thank you for selecting this YAMAHA subwoofer system. CAUTION: Read this before operating your unit Please read the following operating precautions before use. YAMAHA will not be held responsible for any damage and/or injury caused by not following the cautions below. • To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
SPECIAL INSTRUCTIONS FOR U.K. MODEL IMPORTANT: THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
PLACEMENT One subwoofer will have a good effect on your audio system, however, the use of two subwoofers is recommended to obtain more effect. A If using one subwoofer, it is recommended to place it on the outside of either the right or the left front speaker. (See fig. A .) If using two subwoofers, it is recommended to place them on the outside of each front speaker. (See fig. B .) The placement shown in fig.
CONNECTIONS Choose one of the following two connecting methods that is more suitable for your audio system. ■ Choose 1 (pages 3-4) when you want to enjoy 5.1 surround system ■ Choose 2 (pages 5-6) when you want to output the low frequency signals Caution Unplug the subwoofer and other audio/video components before making connections. Notes • All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”.
CONNECTIONS ■ Using one subwoofer Subwoofer OUTPUT TO SPEAKERS INPUT 2 OUTPUT TO SPEAKERS HIGH CUT /MONO VOLUME INPUT 2 Mono pin cable (not included) HIGH CUT HIGH LOW INPUT 1 FROM AMPLIFIER Audio pin cable (not included) /MONO POWER ON OFF HIGH LOW INPUT 1 FROM AMPLIFIER To AC outlet Amplifier ■ Using two subwoofers Mono pin cable (not included) OUTPUT TO SPEAKERS INPUT 2 HIGH CUT OUTPUT TO SPEAKERS /MONO INPUT 2 HIGH CUT /MONO HIGH LOW HIGH LOW INPUT 1 FROM AMPLIFIER INPUT
CONNECTIONS Connecting to speaker output terminals of the amplifier 2 Select this method if your amplifier has no line output (pin jack) terminal. If your amplifier has two sets of front speaker output terminals and both terminals can output sound signals simultaneously. • Connect one set of front speaker output terminals of the amplifier to the INPUT 1 terminals of the subwoofer, and connect the other set of front speaker output terminals of the amplifier to the front speakers.
CONNECTIONS If your amplifier has only one set of front speaker output terminals. Connect the speaker output terminals of the amplifier to the INPUT 1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the front speakers.
CONNECTIONS Connecting to the INPUT 1/OUTPUT terminals of the subwoofer For connection, keep the speaker cables as short as possible. Do not bundle or roll up the excess part of the cables. If the connections are faulty, no sound will be heard from the subwoofer or the speakers, or both of them. Make sure that the + and – polarity markings of the speaker cables are observed and set correctly. If these cables are reversed, the sound will be unnatural and lack bass.
CONTROLS AND THEIR FUNCTIONS Subwoofer rear panel OUTPUT TO SPEAKERS INPUT 2 2 OUTPUT TO SPEAKERS HIGH CUT /MONO 34 INPUT 2 HIGH CUT VOLUME HIGH LOW INPUT 1 FROM AMPLIFIER /MONO 1 POWER ON VOLUME OFF HIGH LOW INPUT 1 FROM AMPLIFIER 7 1 POWER switch Press this switch to the ON position to turn on the power to the subwoofer. When the power of the subwoofer is on, the power indicator (4) on the rear panel light up in green.
ADJUSTING THE SUBWOOFER BEFORE USE Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and the front speakers by following the procedures described below. Subwoofer rear panel OUTPUT TO SPEAKERS INPUT 2 1,6 OUTPUT TO SPEAKERS HIGH CUT /MONO INPUT 2 HIGH CUT VOLUME HIGH LOW INPUT 1 FROM AMPLIFIER /MONO 3 POWER ON VOLUME OFF HIGH LOW INPUT 1 FROM AMPLIFIER 5 1 2 3 Set the VOLUME control to minimum (0).
ADJUSTING THE SUBWOOFER BEFORE USE Frequency response The frequency response of this subwoofer dB 90 HIGH CUT HIGH 80 70 60 HIGH CUT LOW 50 40 20 50 100 200 500Hz The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer is combined with a typical front speaker system. ■ EX.1 When combined with a 4” or 6.
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY II In 1988, Yamaha brought to the marketplace speaker systems utilizing YST (Yamaha Active Servo Technology) to give powerful, high quality bass reproduction. This technique uses a direct connection between the amplifier and speaker, allowing accurate signal transmission and precise speaker control.
TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center. Problem Cause What to Do Power is not supplied even though the The power plug is not securely connected. Connect it securely. The volume is set to minimum. Raise the volume up. Speaker cables are not connected securely.
SPECIFICATIONS Type .....Advanced Yamaha Active Servo Technology II Power Consumption .............................................. 45 W Driver........................................25 cm (10”) cone woofer Magnetic shielding type Dimensions (W x H x D) ...................................... 340 mm x 340 mm x 385 mm (13-3/8” x 13-3/8” x 15-5/32”) Output Power .............. 50 W (100 Hz, 5 Ω 10 %T.H.D) Dynamic Power ............................................ 100 W, 5 Ω Input Impedance ...............
© 2006 YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND SCANDINAVIA A.
