數位主動式喇叭 使用說明書
重要安全指示 小心 觸電危險,請勿開啟 小心:防止觸電危險,勿移開蓋子(或背板), 內部無使用者可自行維修之零件,請洽合格服 務人員維修。 圖形說明 正三角形內的閃電箭頭圖樣,是用來警告您產品內有未經絕緣 之 “危險電壓”,其強度足以對人員造成觸電的危險。 正三角形內的驚嘆號圖樣,代表本組件附帶有關產品的重要操 作和維修使用說明書。 1 2 3 4 5 6 7 8 閱讀指示。 保留指示。 注意所有的警示。 遵循所有的指示。 使用本產品時勿靠近水氣。 只能使用乾布來清潔。 勿阻礙任何通風口。請遵照製造商指示安裝本組件。 本組件不可擺置在散熱器、電熱器、爐子或其他會發熱的產品(包括擴大機) 等熱源的旁邊。 9 切勿破壞極化或接地型插頭之安全目的:極化插頭具有二葉片,其中一片 寬些。接地型插頭具有二葉片和一第三支接地插腳。寬的葉片和第三支插 腳附有安全目的。假如附贈的插頭不能插入插座,洽電氣人員更換舊式的 插座。 10 保護電源線以免被踩踏或是擠壓,特別是勿擠壓到插頭、一般插座以及電 源線接出機箱處的電線。 11 限使用製造商所指定的安裝附件/配件。 12 限使用製造商所指定的或隨產品販賣之推車、腳架、
注意事項:操作本機前請先閱讀此頁 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 為了保證最佳的性能,請仔細閱讀本手冊。請妥善保管以備日後查閱。 將本音響系統安裝在通風、涼爽、乾燥、清潔的地方 — 遠離陽光直射、 熱源、振動、骯髒、潮濕和寒冷的地方。為了良好的地方,請遵循下列最 少保留的空間。 上方:5 cm (2 in),後方:5 cm (2 in),兩側:5 cm (2 in) 將本機遠離其他電器,馬達或變壓器放置,以避免產生蜂鳴雜訊。 不要將本機突然從低溫環境轉移到高溫環境,也不要將其置於高濕場所(亦 即,放置有增濕器的房間),以防止本機內部結露。結露可能導致觸電、火 災、本機損壞及/或人員傷害。 避免將本機放置於異物容易落入的場所及/或液體飛濺的地方。在本機上 方,不要放置下列物品: 其他裝置,因為它們可能損害本機或使本機的外表變色。 燃燒中的物品(亦即,蠟燭),因為它們會引起火災、損壞本機及/或人員 傷害。 盛有液體的容器,因為其中的液體有可能傾倒進入本機,使得用戶觸電 及/或損壞本機。 不要使用報紙、桌布、窗簾等物遮蓋本機,以免妨礙散
遙控器與電池注意事項 請勿將水或其他液體濺灑在遙控器上。 遙控器請勿掉落。 請勿使遙控器處於或儲存於下列情況中: - 高濕度的地方,例如浴室附近 - 高溫度的地方,例如加熱器或爐子附近 - 溫度極低的地方 - 骯髒的地方 根據極性標示(+和-)裝入電池。 如果電池幾經使用很久,遙控器的有效操作範圍將會顯著降低。如果發生這 種情況,盡快更換兩顆新電池。 如果電池電力耗盡,立即從遙控器取出,以防止爆炸或酸液洩漏。 如果您發現電池漏液,請立即丟棄電池,小心不要觸碰洩露的物質。如果洩 漏的物質接觸皮膚或濺入眼睛或口,請立即沖洗並洽詢醫生。在安裝新的電 池,務必徹底清潔電池盒。 不要新舊電池混用。這可能會縮短新電池的壽命或使舊電池漏液。 請勿同時使用不同類型的電池(例如鹼性電池和錳電池)。 即使外觀看起來相同,電池規格可能會不同。 插入新電池之前,務必徹底清潔電池盒。 請將電池遠離兒童。如果意外吞下電池,請立即聯繫您的醫生。 假如長時間不使用遙控器,請取出遙控器內的電池。 所附的電池不要充電或拆解。 有關更多詳細資訊,請參閱 CD-ROM 上的使用者手冊。若要觀
目錄 特性 4 播放 39 可以使用本機做什麼 ......................................................................... 4 所附配件 ........................................................................................ 6 播放的基本操作 .............................................................................. 39 依據偏好享受聲音 ........................................................................... 40 準備遙控器 ............................................................................................................... 7 使用環繞聲播放 ...
網路 50 網路功能與 MusicCast CONTROLLER 應用程式 ............................. 50 附錄 94 故障排除 ....................................................................................... 94 使用 MusicCast CONTROLLER 應用程式連接 一般 ........................................................................................................................ 94 (將本機登錄為可啟用 MusicCast 的裝置) ............................................................... 50 Bluetooth .....................................................................
特性 可以使用本機做什麼 採用獨特的真實環繞聲格式和技術,自牆壁反射音束,讓聆聽者欣賞自 己喜歡的聲學環境。 各種支援的內容 ․ 自動且快速的調整環繞聲效果來配合聆聽空間的設置 (IntelliBeam) ● 媒體伺服器(PC/NAS) ․ 使用如實際電影院及音樂廳的音場重現立體聲或多聲 道音效(CINEMA DSP) 行動裝置專用的 應用程式 ․ 使用強化聲音享受壓縮的音樂(Compressed Music Enhancer) ● 網際網路廣播電台 ● AirPlay ● 儲存在行動裝置的音樂 ․ 將聲音傳遞至指定的位置(目標播放模式) 音訊 HDMI 控制 TV、本機和 BD/DVD 播放機的循序操作(HDMI 控制) 音訊/ 視訊* 音訊 行動裝置 網路內容 控制 音訊 TV 遙控器 MusicCast 裝置 經由家庭網路 分享音樂 音訊 控制 中央主機(本機) HDMI 控制 音訊/ 視訊* 自 Bluetooth裝置播放音訊 內容 音訊 行動裝置 無線超重低音喇叭 (本機) 本機的遙控器 使用 Bluetooth 耳機或喇叭 聆聽輸入至本機的音訊
使用 MusicCast CONTROLLER 在網路上無限播 放音樂 行動裝置專用的免費應用程式 MusicCast CONTROLLER,可用來聆聽儲存在 如智慧型手機之類的行動裝置或伺服器上的音樂,或是聆聽網際網路廣播電台 及許多種主流串流服務。 關於本手冊 ● 在本手冊中,可以使用前面板按鍵或遙控器來進行的操作,使用遙控器來 做說明。 ● 表示為更有效使用的補充解釋。 ● 指示有關本機使用的注意事項及功能限制。 此應用程式也可用來將內容分配給其他啟用 MusicCast 的裝置,以進行同步播 放。 MusicCast CONTROLLER 應用程式也可用來執行選擇輸入訊號源及調整音量 這類的任務。 有關詳情請參閱 “MusicCast 設定指南” 或拜訪 Yamaha 網站。 請在 App Store 或 Google Play 上搜尋 “MusicCast CONTROLLER”。 Bluetooth 功能 可以從 Bluetooth 組件接收及播放音訊,例如無線連接的行動裝置。也可以將 輸入至本機的音訊傳送至 Bluetooth 耳機。 ● 在本手冊中,iOS 和 Android 行
所附配件 在連接之前,請確保您已收到以下所有項目。 YSP-2700 中央主機(YSP-CU2700) 無線超重低音喇叭(NS-WSW121) 遙控器 電池(AAA、R03、UM-4)(x2) 光纖訊號線* (1.5 m (4.9 ft)) IntelliBeam 麥克風 (6 m (19.
準備遙控器 安裝電池或使用遙控器之前,務必閱讀 “快速參考指南” (另外的手冊)中的電池和遙控器注意事項。 █ 安裝電池 █ 操作範圍 2 個電池(附贈) (AAA、R03、UM-4) 壓下箭頭處並從箭頭所 指方向滑動蓋子。 6 m (20 ft)以內 將蓋子往回滑以關閉。 特性 所附配件 7
控制鍵與功能 █ 本機(前面、上方) 前面板顯示器 顯示本機的設定,例如音訊輸入訊號源的名稱 或是環繞模式(p.45)。也會顯示出設定值。 CONNECT 鍵 使用 MusicCast CONTROLLER 應用程式將本 機連至網路(p.50)。 指示燈 亮起顯示系統狀況。 亮綠燈:電源開啟 亮紅燈:電源關閉(當啟動 HDMI 控制或網路待 機時) 熄滅:電源關閉 INPUT 鍵 選擇一音訊輸入訊號源。 (Wi-Fi)指示燈 顯示無線網路連接狀態(p.27)。 (Bluetooth)指示燈 顯示 Bluetooth 連接狀態(p.47, 49)。 MUTE 鍵 聲音靜音(p.39)。 VOLUME (+/-)鍵 調整本機音量(p.39)。 ● 當本機關閉時,本機消耗少量的電力,以便搜 尋 HDMI 訊號,或接收來自網路裝置的訊號。 ● 前面板顯示器只有在本機操作時才會開啟 3 秒 鐘。 ● 在設定選單中,“Dimmer” 可以調整前面板顯示 器與指示燈的亮度(p.85)。 鍵 開啟或關閉本機。 遙控感應器 接收來自遙控器之紅外線訊號(p.
█ 中央主機(後面板) INTELLIBEAM MIC 插孔 用於連接附贈的 IntelliBeam 麥克風(p.33)。 SYSTEM CONNECTOR 插孔 使用有線連接來連接至附贈的超重低音喇叭 (p.29)。 SUBWOOFER OUT 插孔 使用有線連接來連接至附贈的超重低音喇叭 (p.29)。 AUX1 輸入插孔 用於連接至具有類比數位音訊輸出插孔的播放 裝置(p.26)。 AUX2 輸入插孔 用於連接至具有數位同軸數位音訊輸出插孔的 播放裝置(p.25)。 TV 輸入插孔 用於連接至具有數位光纖數位音訊輸出插孔的 播放裝置(p.24)。 NETWORK 插孔 用於使用網路訊號線連接至網路(p.27)。 HDMI OUT (ARC)插孔 用於連接至 HDMI 相容 TV 和輸出視訊/音訊訊 號(p.24)。 HDMI 1-3 插孔 用於連接 HDMI 相容播放裝置,例如 BD/DVD 播放機、衛星及有線 TV 調諧器以及遊戲機 (p.25)。 UPDATE ONLY 插孔 用來更新本機的韌體(p.92)。 天線 安裝本機後升起天線(p.23)。 電源線 用於連接至 AC 牆壁插座(p.
█ 遙控器 紅外線訊號傳輸器 ECO 鍵 開啟或關閉 Eco 功能(p.45)。 輸入選擇器鍵 選擇即將要播放的音訊輸入訊號源(p.39)。 ● NET 鍵:經由網路選擇一音訊輸入訊號源 (p.50)。每按一次按鍵,就會以下列順序選擇 輸入訊號源: SERVER → NET RADIO → AirPlay → Streaming music service (若有的話) → MusicCast Link → SERVER →… ● HDMI 1-3 鍵:用於連接至 HDMI 1-3 插孔的 裝置(p.39) TV 鍵:用於連接至 TV 輸入插孔的裝置(p.39) AUX 1 與 2 鍵:用於連接至 AUX 1 與 2 輸 入插孔的裝置(p.39) ● 鍵:用於 Bluetooth 裝置(p.48) SYSTEM MEMORY 鍵 儲存 IntelliBeam 測量、揚聲器音量及其他設定 (p.46)。 SUB (+/-)鍵 調整超重低音喇叭音量(p.39)。 SETUP ( )鍵 顯示設定選單(p.69)。 鍵,ENTER 鍵 變更設定(p.
█ 超重低音喇叭(後面板) 電源線 用於連接至 AC 牆壁插座(p.28)。 SYSTEM CONNECTOR 插孔 使用有線連接連接至中央主機(p.29)。 SUBWOOFER PAIRING 按鈕 用來手動配對中央主機與超重低音喇叭(p.105)。使用大頭針或其他尖銳物品 按壓此鍵。 INPUT 插孔 使用有線連接連接至中央主機(p.29)。 STATUS 指視燈 顯示超重低音喇叭的連接狀態(p.
準備 一般設定程序 1 安裝(p.13) 擺放本機以達到最理想環繞聲效果。 2 連接 TV (p.24) 連接 TV 至本機。 3 連接播放組件(p.25) 連接視訊組件(例如 BD/DVD 播放機)至本機。 4 連接網路(p.27) 使用網路訊號線將本機連接至路由器以準備建立有線網路連接。也提供了有關連接至無線網路 的資訊。 5 連接電源線(p.28) 完成所有的連接後,插入電源線。 6 初始化設定(p.30) 在嘗試播放前,請先執行初始化設定,例如調整環繞聲效果。 現在所有準備已完成。請使用本機享受播放電影、音樂與其他內容! ● 有關網路連接和經由網路播放音訊的資訊,請參閱 “NETWORKS” (p.
1 安裝 本機反射牆壁音束來創造環繞聲效果。為達到想要的環繞聲效果,本機與聆聽位置及牆壁的相關位置是重要的。安裝本機時請參閱第 13 至 17 頁。例如,如果要在 後面空間有限的音響安裝本機時,首先應考慮它能更容易將外接組件連接到本機。這要取決於安裝位置。有關外接組件的連接資訊,請參閱第 24 至 27 頁。 小心 ● 務必將中央主機安裝在大又穩的支架且不易受振動影響,例如地震造成的震動,以及兒童接觸不到的地方。 注意 ● 本機之超重低音喇叭無防磁功能。在超重低音喇叭附近請不要安裝硬碟裝置或類似的裝置。 ● 請不要將中央主機與超重低音喇叭直接堆疊在其他播放組件的上方。反之亦然,因為熱源和震動可能導致損壞或故障。 █ 建議安裝處所 ● 請將本機安裝在左側及右側牆壁的中間位置。 ● 如果天線是升起的(p.23),在放置中央主機時不可讓 天線干擾到 TV 螢幕。 ● 如果中央主機的放置高度不足,裝上支架(p.18)*。 ● 中央主機可以使用選配的 Wall Muount Bracket SPMK20 安裝在牆壁上(p.
█ 本機安裝範例 平行安裝 本機如下圖所示輸出音束。請將本機安裝在不會有阻礙音束路徑的障礙物的地 方,例如家具。 盡可能將本機安裝在牆壁的正中心位置。 否則,就無法達到想要的環繞聲效果。 如果本機與牆壁平行安裝,請盡量安裝在牆壁的正中央位置。 如果本機安裝在房間一角,請與鄰接牆壁保持 40 - 50°。 平行安裝 物品,例如家具 ● 如果無法將本機平均的安裝在左右牆壁之間,可以調整音束來達到自然的環 繞聲效果(p.17)。 理想的安裝位置 盡可能將本機安裝在靠近正常聆聽位置的正前方。聆聽位置與本機之間的距離 必須超過 1.8 m (6 ft)。 音束輸出會因為環繞聲設定(p.40)以及聲道輸出設定(p.75)而不同。上圖是在 啟用環繞聲播放以及將 Channel Out 設定中的 “Front” 設定至 “Beam” 時的 音束路徑。 角落安裝 40°至 50° 物品,例如家具 上圖是在啟用環繞聲播放(p.40)以及將 Channel Out 設定中的 “Front” 設定 至 “Stereo” 時的音束路徑(p.75)。 超過 1.8 m (6 ft) 超過 1.
安裝在非方形的房間 將本機安裝在音束可以從牆壁反射的位置。 有一面是走廊開口的不規則形房間 所有方向都有實心牆壁的不規則形房間 ● 如果無法重新放置本機,或是無法改變聆聽位置,可以安裝選配的 YRB100 聲音反射板來獲得更佳的環繞聲體驗(p.
本機安裝於客廳的範例 █ 不建議的聆聽環境 ● 跨在桌上的雙腳不被視為障礙物,因為音束通常可以穿過它們。面對牆壁安 裝的櫥櫃會反射聲音。 本機藉由反射聆聽房間的牆壁所投射的音束來創造環繞聲。當本機安裝於下列 位置時,本機所產生的環繞聲效果可能會不足。 ● 因為厚重的窗簾會吸收聲音,所以當窗簾拉起與窗簾打開時,聆聽房間內的 聲音特性會不同。使用儲存設定功能,儲存每個聆聽房間的最佳設定 (p.46)。 ● 牆壁不足以反射音束的房間 物品,例如家具 ● 牆壁採吸音設計的房間 ● 超過以下尺寸範圍的房間: W (3 至 7 m (10 至 23 ft)) x H (2 至 3.5 m (7 至 11.5 ft)) x D (3 至 7 m (10 至 23 ft)) ● 諸如家具類的物品很可能阻擋音束路徑的房間 ● 聆聽位置與本機距離小於 1.
█ 調整音束以達到最佳的環繞聲效果 本機的 AUTO SETUP (p.32)可根據聆聽房間的設定,自動調整音束以達到最佳的環繞播放環境。除了使用 AUTO SETUP 之外,當本機以下述方式安裝時,也可手 動調整音束以達到最適合聆聽房間的環繞聲效果。 將本機安裝在靠近房間的一角 將本機安裝在形狀不規則的房間 當如下圖所示將本機安裝在靠近房間的ㄧ角時,如果使用 AUTO SETUP 來配 置音束設定,前方聲道的聲音就像是來自於不自然的方向。 當本機安裝在非矩形的房間時,如下圖所示,音束無法正確的從牆壁反射。 若是發生這種情況,請使用設定選單中的 “Image Location” (p.74)來調整左前 與右前聲道,以獲得更自然的聲音。 當左前聲道的聲音不自然時 若是發生這種情況,請執行 AUTO SETUP,然後使用設定選單中的 “Horizontial Angle” (p.
█ 安裝支架 安裝左邊與右邊的支架。 如果中央主機的安裝高度不足,將本機附贈的支架裝到中央主機以增加其安裝 高度。 1 拆下支架上的封蓋。 封蓋 2 將支架上的突出部分對準後面板上的安裝孔然後插入。 拆下支架 直接將支架拔出來。 突出部分 安裝孔 確實壓緊。 準備 1 安裝 18
█ 將中央主機安裝在牆壁上 安裝 SPM-K20 如果 TV 是安裝在牆壁上,可使用選配的壁掛托架 SPM-K20 將本機安裝在 TV 下的牆壁上。 要安裝壁掛托架的牆壁與本機之間一定要有足夠的空間。請遵照下列指示來安 裝兩者。 本機與 SPM-K20 的尺寸請參考 “尺寸” (p.
2 將本機附贈的模板安裝到牆壁,並使用圖釘或是大頭針在牆壁上標示出螺絲要鎖入的位置記號。 模板 將模板安裝到牆壁使其中心與 TV 的中心對齊。 3 壁掛托架的設計稍微偏向本機中心的右側。 在標示出螺絲位置後,移開模板。 將壁掛托架固定到牆壁上。 將自攻螺絲(未附贈)鎖進使用模板標示的牆壁,不要 鎖到底。 將壁掛托架固定到這些螺絲上,然後鎖緊螺 絲。 至少要將包括之前使用的兩根螺絲在內的六根自攻螺絲 鎖進壁掛托架外緣的螺絲孔內,以確保獲得足夠的強 度。 準備 1 安裝 20
5 將市售訊號線連接至本機。 ● 務必要將螺絲鎖入牆壁或柱子的堅固部分。不可將托架安裝到由灰漿或是膠 合板這類會破裂或剝落的材料所製成的牆壁上。如果螺絲脫落,壁掛托架也 會掉落,導致損壞或受傷。 25 mm 或以上 易彎曲的 HDMI 訊 號線或直角接頭 25 mm 或以上 樑,等等 樑,等等 石牆 4 6 將本機安裝到牆壁上。 使用也是本機附贈的螺絲,將本機附贈的墊圈安裝到本機底部。 螺絲 墊圈 將本機的螺絲插入壁掛托架左右兩側的安裝孔,然後將本機滑向左邊。 在將本機固定到壁掛托架後才可以鎖緊螺絲。 在安裝或是拆除本機時,請用雙手牢牢握住本機。如果本機掉落,會造成損害 或受傷。 準備 1 安裝 21
7 鎖緊螺絲。 尺寸 鎖緊第 4 步驟中用來將墊圈安裝到本機的螺絲。 準備 1 安裝 22
█ 升起天線 在連接無線路由器(存取點)以使用網路時,將本機後面板上的天線升起。 將天線升起到直立位置 時握住天線的底部。 ● 勿對天線過度用力,否則可能損壞它。 ● 一定要檢查天線移動的方向並將其對準正確方向的角度。 ● 請不要拆下天線。 ● 有關無線連接詳情,請參閱 p.
2 連接 TV 將 TV 連接至本機,所以輸入至本機的視訊訊號能輸出至 TV。也可以在本機享受 TV 音訊的播放。 建議使用一條印有 HDMI 品牌識別的 19 支插腳 HDMI 訊號線。建議使用不超過 5 m (16 ft)的訊號線以防止訊號品質劣化。 使用高速 HDMI 訊號線來播放 3D 及 4K 的視訊內容。 本機支援 HDCP 2.2 版,複製保護技術。若要享受 4K 視訊,請將本機連接至 HDCP 2.2 相容 TV 的 HDMI IN 插孔(與 HDCP 2.2 相容的那個)。 若要播放 4K (4:4:4)視訊內容,請將進階設定中的 “4K MODE” 設定至 “MODE 1” (p.
3 連接播放組件 連接視訊組件,例如 BD/DVD 播放機、機上盒(STBs)和遊戲機至本機。依據視訊組件可使用的視訊/音訊輸出插孔,選擇下列其中一種連接。如果視訊組件配置 HDMI 輸出插孔,建議使用 HDMI 連接。 █ HDMI 連接 █ 同軸連接 使用 HDMI 訊號線(未附贈)將視訊組件連接到本機。 使用同軸數位訊號線將視訊組件連接至本機。接著將視訊組件的視訊輸出連接 至 TV 的視訊輸入。 本機支援 HDCP 2.2 版,複製保護技術。 本機(後面) 至視訊 輸出插孔 視訊組件 本機(後面) 視訊組件 HDMI IN 1-3 插孔 HDMI 輸出 AUX2 (同軸數 位)輸入插孔 音訊輸出 (同軸數位) 使用遙控器上的 HDMI 1-3 鍵切換輸入至 HDMI 1-3,即可經由本機播放視訊組 件上的音訊/視訊。 ● 一旦啟動 HDMI 控制功能(p.
█ 類比連接 使用立體聲訊號線(未附贈)將視訊組件連接至本機。接著將視訊組件的視訊輸 出連接至 TV 的視訊輸入。 本機(後面) 視訊組件 至視訊 輸出插孔 AUX1 (類比) 輸入插孔 音訊輸出 (類比) TV 至視訊 輸入插孔 使用遙控器上的 AUX 1 鍵將輸入切換至 AUX1,在視訊組件上播放的音訊將會 從本機輸出。 準備 3 連接播放組件 26
4 連接網路 無線網路 若要連接網路,務必將本機插入 AC 牆壁插座,然後將本機連接至無線路由 器(存取點)。 有線網路連接 有關連接至無線路由器(存取點)請參考以下指示。 若要使用有線網路連接,請經由 STP 網路訊號線(CAT-5 或更高規格直通訊號 線,未附贈)連接本機至路由器。 ● 使用 MusicCast CONTROLLER 應用程式(p.50) ● 使用 MusicCast CONTROLLER 應用程式外的連接方法(p.53 至 59)。 Network Attached Storage (NAS) 網際網路 網際網路 無線路由器 (存取點) 數據機 數據機 PC 網路訊號線 路由器 行動裝置 當本機連接至無線網路時,前面板上的 行動裝置 本機 指示燈亮燈。 亮燈(綠色) ● 您不能同時使用無線網路連接和有線網路連接或 Wireless Direct (p.
5 連接電源線 完成所有的連接後,插入中央主機與超重低音喇叭的電源線。 中央主機 至 AC 牆壁插座 超重低音喇叭 至 AC 牆壁插座 準備 5 連接電源線 28
連接超重低音喇叭 將超重低音喇叭的電源線插入牆壁插座。當中央主機開機時,中央主機與超重 低音喇叭會經由無線連接自動連接。一旦成功的建立連接,超重低音喇叭上的 STATUS 指示燈就會亮起,如下所示,而且本機也準備好播放。 STATUS 指示燈 亮綠燈 ● 如果 STATUS 指示燈沒有在本機開機時就正確的亮起,請手動配對中央主機 與超重低音喇叭。參閱 “配對中央主機與超重低音喇叭” (p.105)。 如果超重低音喇叭沒有聲音,或是因為受到其他裝置的無線電波影響使得聲 音斷斷續續時,請使用訊號線連接中央主機與超重低音喇叭就可解決問題。 使用 RCA 單音訊號線及 3.5 mm 單聲道迷你插頭訊號線連接中央主機與超 重低音喇叭。3.5 mm 單聲道迷你插頭訊號線需要將中央主機與超重低音喇 叭同時開啟與關閉。 RCA 單音訊號線 3.5 mm 單聲道迷你插頭訊號線 使用有線連接來連接中央主機與超重低音喇叭時,請將設定選單中的 “Subwoofer” 的 “Bass Out” 設定至 “Wired” (p.
6 初始設定 在 TV 上顯示選單螢幕 經由在 TV 上顯示選單螢幕,就可 在本機進行視覺操作。 選單顯示 TV 遙控器(範例) 開啟本機及 TV,然後使用 TV 遙 控器上輸入鍵切換輸入,以顯示 本機輸入的視訊。 切換輸 入訊號 源 當本機和 TV 如下方所示連接時, 請使用 TV 的遙控器選擇 “HDMI 1”。 當按下 SETUP ( )鍵或 OPTION ( )鍵時,在 TV 螢幕會顯 示選單。當 TV 正在接收 HDMI 訊號時,選單會疊放在視訊 內容上面。再按一次 SETUP ( )鍵或 OPTION ( )鍵可取消 選單顯示。 TV 本機(後面) ● 設定選單(p.
初始螢幕顯示 當購買之後首次開啟本機時,將顯示下方螢幕。(前面板顯示器顯示 “ViewScreen”。) 選擇選單顯示的語系 1 開啟本機和 TV。 2 切換 TV 的輸入以顯示來自本機的視訊輸入(p.30)。 3 按住 SETUP ( )鍵直到 TV 上出現 “OSD Language” 選單。 遵照螢幕指示使用 iOS 裝置(iPhone 等)將本機連接至無線網路。 當使用安裝在行動裝置上的 MusicCast CONTROLLER 應用程式時,更容易 )鍵取消此螢幕,然後參考 p.50。 將本機連接至無線網路。按 RETURN ( ● 如果本機經由 NETWORK 插孔(有線連接)連接到一個路由器,就不會顯 示此螢幕。 當未顯示選單時 ● 確認下列情況。 ● 請注意,如果在上面所示的螢幕顯示時連接 IntelliBeam 麥克風(p.
自動設定適當的環繞效果(IntelliBeam) 首先使用 “IntelliBeam” 功能來調整每個聲道,讓本機提供最佳的觀看與聆聽 環境。 2 將附贈的硬紙板麥克風架與 IntelliBeam 麥克風放置在聆聽位置。 ● 放置 IntelliBeam 麥克風,使其高度與坐下來時的耳朵高度一樣。 ● 如果本機安裝在 “不建議的聆聽環境” (p.16)中所述的其中一種房間,可能無 法成功運行 AUTO SETUP 程序。在這些類型的房間也可使用 My Surround 功能來享受豐富的環繞聲。更多資訊請參閱 “Channel Out” (p.75)。 ● 將 IntelliBeam 麥克風與地板平行放置。 ● 也可使用相機三角架或凳子來替代附贈的硬紙板麥克風架。 ● 不可將 IntelliBeam 麥克風連接至延長線,因為這樣會造成聲音優化不精 確。 IntelliBeam 麥克風 上限 本機的中間高度 █ 安裝 IntelliBeam 麥克風 1 m (3.3 ft)之內 1 1 m (3.
█ 始用 AUTO SETUP (IntelliBeam) 在將 IntelliBeam 麥克風連接至本機後,顯示下列螢幕。 ● 測量期間輸出的測試音量是大聲的。請在兒童不在場且不會進入聆聽房間時 執行 AUTO SETUP,否則他們的聽力可能會受損。 ● 如果聆聽房間內有窗簾,建議遵照下列程序。 1. 打開窗簾以改善聲音反射。 2. 執行 “Beam optimize only” (p.35)。 3. 關上窗簾。 4. 執行 “Sound optimize only” (p.35)。 ● 請確認聆聽房間可盡可能保持安靜。為獲得精準的測量,請關閉空調或其他 會產生噪音的設備。 “IntelliBeam” 選單中的 “AUTO SETUP” 可自動調整下列兩設定。 1 開啟本機與 TV。 Beam optimize only 2 切換 TV 輸入至連接本機的輸入插孔(HDMI 1 等)(p.
4 按 ENTER 開始 AUTO SETUP 程序,然後在 10 秒內離 開房間。 5 按 ENTER 鍵。 使用測量結果並儲存到本機。 測量進行時螢幕 會自動改變。 如果 AUTO SETUP 程序完成,本機會發出鐘鳴聲。 ● AUTO SETUP 程序約需 3 分鐘。 ● 若要在 AUTO SETUP 程序開始後取消,或是不想要應用 其結果,請按 RETURN ( )鍵。 ● 按 SYSTEM MEMORY 1、2 或 3 鍵,就可儲存數個測量 結果。 當按下 SYSTEM MEMORY 1 鍵時,顯示 “M1 Saving” 並將設定儲存。 ● 如果在測量開始後接收到環境噪音,錯誤訊息就會顯示在 “AUTO SETUP COMPLETE” 螢幕,提示要重新開始測 量。請按 ENTER 鍵退出錯誤訊息螢幕,然後開始重新測 量。 ● 如果發生錯誤,就會發出蜂鳴聲並顯示錯誤訊息。有關錯 誤訊息的詳情,請參閱 “如果顯示錯誤訊息” (p.
經由設定選單的 AUTO SETUP “Beam optimize only” 或 “Sound optimize only” 可在設定選 單中分開測量。 1 將 IntelliBeam 麥克方放在正常的聆聽位置,然後按 SETUP ( )鍵。 有關 IntelliBeam 麥克風定位的指示請參閱 “安裝 IntelliBeam 麥克風” (p.32)。 2 按 鍵選擇 “Beam” 然後按 ENTER 鍵。 3 按 鍵選擇 “IntelliBeam” 然後按 ENTER 鍵。 4 按 鍵選擇以下其中一個項目然後按 ENTER 鍵。 5 在顯示 “AUTO SETUP (PREPARATION & CHECK)” 螢 幕之後,將 IntelliBeam 麥克風連接至本機。 有關連接 IntelliBeam 麥克風的詳情,請參閱 “使用 AUTO SETUP (IntelliBeam)” (p.
如果顯示錯誤訊息 如果 TV 螢幕顯示一個錯誤訊息,請參閱下列的 "錯誤訊息" 來判定原因並解決問題。請遵照 TV 螢幕上顯示的指示開始重新測量。 錯誤訊息 錯誤訊息 原因 解決方法 關閉空調這類製造噪音的裝置,或將本機搬離 這類裝置。 ERROR E-1 Please test in quieter environment. 聆聽房間內有太多的噪音。 ERROR E-2 No MIC detected. Please check MIC connection and re-try. IntelliBeam 麥克風解除連接。 將 IntelliBeam 麥克風連接至本機前面的 INTELLIBEAM MIC 插孔,並開始重新測量。 ERROR E-3 Unexpected control is detected. Please retry. 有其他操作在本機執行。 開始重新測量。在測量期間不要在本機執行任 何其他操作。 ERROR E-4 Please check MIC position.
使用 TV 遙控器操作本機(HDMI 控制) █ 何謂 HDMI 控制功能? 除了左側欄位的功能外,有些 TV 也可操作顯示於 TV 的本機選單。 HDMI 控制功能(連接功能)讓 TV 與本機的操作一致,所以可以使用 TV 的遙控 器操作本機。 當使用 HDMI 訊號線將 TV 連接至本機時,就可使用 TV 的遙控器來執行下列 操作。 ● 縱使您的 TV 支援 HDMI 控制功能,有些功能還是無法使用。相關詳情,請 參閱 TV 所附的文件。 ● 建議使用來自於相同製造商的組件(TV、BD/DVD 播放機等)。 經由 TV 遙控器的協同功能 1. 電源開/關 TV 遙控器(範例) 同時開啟/關閉 TV 和本機。 2.
█ 變更 HDMI 控制功能 如果組件未協同 如果無法使用 TV 的遙控器操作本機,請如下配置 HDMI 控 制功能。 確認設定是如下所述正確配置的。 1 - 在 TV 上啟動 HDMI 控制功能。 2 開啟本機、TV 和播放組件。 - 在設定選單中 “HDMI Control” (p.80)設定至 “On”。 TV 設定的範例 啟動本機,TV 和播放組件的 HDMI 控制功能,例如支援 本功能的 BD/DVD 播放機。 ● 從 TV 的設定選單選擇 “Link setting” “HDMI control setting”,然後進行設定,例如將 “HDMI control function” 設定至 “ON”。 使用本機,請確認 “HDMI Control” 是設定至 “On” (預設 設定) (p.
播放 播放的基本操作 1 按 5 鍵以開啟本機。 在本機開啟後,可能需要幾秒的時間才會從中央主機與 超重低音喇叭播出聲音。 2 3 按 VOL (+/-)鍵以調整音量。按 SUB (+/-)鍵以調整超重低 音喇叭的音量。 ● 當音訊同時從 TV 喇叭與本機輸出時,TV 靜音。 ● 當輸入至 HDMI IN 插孔的聲音從 TV 輸出時,即始按 下 VOL (+/-)鍵或 MUTE ( )鍵,音量也不會改變。 開啟連接至本機的組件(TV、BD/DVD 播放機、遊戲機 等)。 ● 若要靜音,請按 MUTE ( )鍵。前面板顯示器顯示 “MUTE ON”。若要恢復音量,請再按一次 MUTE ( ) 鍵或按 VOL (+/-)鍵。當按下 MUTE ( )鍵時,前面 板顯示器顯示 “MUTE OFF”。 按下對應至外接組件所連接的輸入選擇器按鍵或 NET 鍵,選擇一組件。 按 HDMI1 鍵以播放經由 HDMI IN1 插孔連接至 BD/DVD 播放機的音訊/視訊內容。 ● 可自整體音量中個別調整超重低音喇叭的音量。 輸入訊號源名稱 ● 建議在夜間時調低超重低音喇叭的音量。 有關從 Blueto
依據偏好享受聲音 本機支援下列功能,依據偏好享受聲音。 ● 環繞播放模式(p.40) ● CINEMA DSP (p.41) 使用環繞聲播放 5 聲道音束創造出一個環繞聲播放音場。 ● 立體聲播放模式(p.42) ● 目標播放模式(p.42) ● Compressed Music Enhancer (p.43) ● CLEAR VOICE (p.43) ● 調整每個聲道的音量(p.43) 音束 前方與後方音束所形成的聲道(p.75) 1 按 SURROUND 鍵切換至環繞聲模式。 前面板顯示器顯示 “SURROUND”。 ● 在設定選單配置 Channel Out 設定(p.
享受三維環繞聲(CINEMA DSP 3D/CINEMA DSP) 依據音訊訊號源及個人偏好選擇想要的 CINEMA DSP 程式。 Yamaha 獨家音場重現技術(CINEMA DSP)可輕鬆重現不輸給 電影院與音樂廳的逼真音場,讓使用者享受自然及三維的聆 聽環境。 1 重複按 CINEMA DSP (MOVIE、MUSIC 或 ENTERTAINMENT) 鍵以選擇想要的程式。 MUSIC (使用 MUSIC 鍵選擇) Music Video 此程式產生一種活躍的環境,讓您猶如置 身於真正的爵士或搖滾演唱會。 Concert 此程式創造出深具臨場感的大型圓形音樂 廳豐富的環繞聲效果,強化聲音的延伸效 果,讓您猶如置身於靠近舞台中央的座位 上。 Jazz Club 此程式重新創造曾經在紐約著名一時的爵 士俱樂部的聲學環境 “The Bottom Line”, 讓您猶如置身於舞台正前方的座位上。 前面板顯示器出現 CINEMA DSP 程式名稱。 ● CINEMA DSP 程式無法在下列情況下使用。 - 在立體聲播放模式(p.42)或目標播放模式(p.
2 聲道播放(立體聲播放模式) 清楚聽到遠方的聲音 啟用使用右前與左前聲道的 2 聲道立體聲播放。當輸出多聲 道音訊訊號時,它們會向下混合成 2 聲道。 1 按 STEREO 鍵以切換至立體聲播放模式。 播放輸入訊號源,並調整音束角度。 1 按 TARGET 鍵。 2 使用 鍵調整音束角度。 每按一次 鍵,左方角度就會增加 2 度;每按一次 鍵,右方角度就會增加 2 度。 每個方向最大的角度是 90 度。 將聲音傳送到指定位置(目標播放模式) 音束角度往左調整 16 度 目標播放模式從單一聲道輸出音束,讓指定位置獲得最佳的 聆聽。 請參照下圖。 解除目標播放模式 低音聆聽,例如晚上 按 SURROUND 鍵或 STEREO 鍵以關閉目標播放模式。 ● CINEMA DSP 程式在目標播放模式下無法啟用。 ● 低音輸出受限以防止聲音往其他方向散布。 播放 依據偏好享受聲音 42
使用豐富的聲音(Compressed Music Enhancer)播放數位壓縮格式(例如 MP3)等 1 2 按住 CH LEVEL 鍵選擇聲道。 FL:左前 播放數位壓縮格式,例如 MP3,加強低音與高音來擴大動態 聲音。 1 按住 CH LEVEL 鍵 3 秒以上。 FR:右前 C:中央 按 ENHANCER 鍵開啟 Compressed Music Enhancer 功 能。 SL:左環繞聲 SR:右環繞聲 再按一次鍵,關閉功能。 SUB:超重低音喇叭 ● 當輸入取樣率大於 48 kHz 的數位音訊訊號時, Compressed Music Enhancer 就會取消。 ● 在目標播放模式無法調整聲道電平。 ● SUB (超重低音喇叭)的音量只能在立體聲播放模式中 調整(p.42)。 ● 當輸入訊號源為 Bluetooth 時,本功能預設為 “ON”。其他 輸入訊號源則是設定為 “OFF”。 ● 當 “My Surround” 設定至 “On” 時,可以調整下列聲 道的音量(p.
調整音調 在聆聽聲音時使用選項選單調整高(高音)與低(低音)音調的電 平。 下列各個輸入訊號源都可設定音調。 HDMI 1-3、TV、AUX 1-2、Bluetooth、NET ● 選項選單顯示並可在 TV 螢幕或前面板顯示器上操作。此 節使用前面板顯示器圖示做為範例。 1 2 3 按住 OPTION (…)鍵。 按 鍵。 鍵選擇 “TREBLE” 或 “BASS” 並按 ENTER 按 鍵調整輸出電平。 可調整範圍是-12 至+12 (預設:0)。 4 按 5 重複步驟 2 與 3 以調整高音與低音的輸出電平。 6 按 OPTION (…)鍵退出選項選單。 鍵。 播放 依據偏好享受聲音 44
使用有用的功能 使用 Eco 功能節省能源 使用 Eco 功能降低本機的耗電量。 Input:輸入訊號源的名稱 (“BLUETOOTH”,或連接組件的名稱會隨著 Bluetooth 輸入顯示。) 當啟用此功能時,前面板顯示器的亮度會降到最低,而且也 會降低最大音量。 Beam:播放模式 1 Decoder:目前的解碼器(p.78) 按 ECO 鍵。 “ECO ON” 顯示且前面板顯示器關閉。 Cinema DSP:CINEMA DSP 程式(p.41) STATUS 指示燈的亮度降到最低。 SUB Status:超重低音喇叭狀態 取消 Eco 功能 按 ECO 鍵。 前面板顯示器顯示 “ECO OFF”。 ● 在播放模式顯示(音束) - SURROUND:在環繞聲模式播放(p.40) - MY SUR.:使用 My Surround 功能播放(p.76) ● 取消此功能以更大的音量播放。 ● 當啟用此功能時,設定選單中的 “Dimmer” (p.85)及進階 設定選單中的 “MAX VOLUME” (p.
儲存本機的設定至系統記憶體 ● 環繞聲播放(p.40)、立體聲播放(p.42)或目標播放模式(p.42) (Channel Out 設定(p.75)也可儲存到環繞聲播放模式。) 本機的記憶體可儲存三組設定值,可視需要用來快速下載適 合特定聽眾的最佳設定或是環境變更。請參照以下範例以儲 存 IntelliBeam 測量結果與設定,例如將環繞設定儲存到系統 記憶體,或是下載預先定義的設定。 ● 環繞聲:CINEMA DSP (p.41) 範例 1 將不同環境適用的 IntelliBeam 測量儲存至系統記 憶體 █ 將設定儲存至系統記憶體 如果有類似窗簾之類會吸收聲音的材料,音束就會受到阻擋 而降低那些音束的效果。請在窗簾開啟時測量並且在關閉時 再測量一次。將兩種設定都儲存到 SYSTEM MEMORY 1 及 2,並視需要下載適合的設定。 範例 2 將常用的設定儲存到系統記憶體 ● 音調控制(p.44) ● 超重低音喇叭設定(p.
經由 Bluetooth 連接無線播放音訊 可用本機來接收及播放來自於 Bluetooth 組件的音訊,以及將音訊傳送到 Bluetooth 組件上播放。 ● 本機自行動裝置等等接收音訊的同時,無法傳輸到揚聲器或耳機。 有關更多資訊請請參閱 Bluetooth 組件所附的文件。 從 Bluetooth 組件接收音訊 ● 設定選單中之 “Bluetooth” 必須設定至 “On” (預設;p.81)以使用 Bluetooth 功能。 來自於 Bluetooth 組件的音訊,例如行動裝置或數位音樂播放器,可以在無線 連接上播放。 ● 指定密碼(PIN)非 “0000” 的 Bluetooth 組件,無法連接至本機。 ● 當連接 Bluetooth 組件至本機時,務必確認兩機之間的距離不可超過 10 m (33 ft)。 ● 如果無法建立 Bluetooth 連接,請參閱 “故障排除” 中的 “Bluetooth” (p.
從 Bluetooth 組件聆聽音樂(接收) 1 按遙控器上的 前面板顯示器顯示 “Connect”。 鍵 選擇 Bluetooth 作為輸入訊號源,前面板顯示器顯示 “BLUETOOTH”。 在 Bluetooth 組件上會顯示 4 指示燈或完成訊息。 在 Bluetooth 組件上播放一首歌曲。 ● 如果之前已經連接過 Bluetooth 組件,當按下 鍵 時,本機會連接到最後連接的組件。終止此連接以連 接新組件。 2 3 開啟 Bluetooth 組件上的 Bluetooth 功能。 依據組件而定,操作會有所不同。請參閱組件所附的文 件。 ● 在某些 Bluetooth 組件上,必須將本機指定為音訊輸出的 目的地。 在組件的 Bluetooth 組件清單上選擇 “YSP-2700”*。 ● 在設定選單中將 “Network Standby” 設定至 “On”,本機 就可隨著 Bluetooth 組件的操作來開啟及關閉(p.84)。 * 如果本機登錄為啟用 MusicCast 的裝置(p.
經由 Bluetooth 喇叭或耳機聆聽音訊(傳輸) 當本機與 Bluetooth 組件正在連接時,本機前面板上的 指示燈會閃爍,且當連接建立時,指示燈持續亮起。 ● 使用 AirPlay 輸入的音樂無法輸出至 Bluetooth 組件。 ● 安裝在行動裝置上的 MusicCast CONTROLLER 應用程式 (p.
網路 網路功能與 MusicCast CONTROLLER 應用程式 網路連接可以讓您經由本機聆聽網際網路廣播電台或音樂串流服務,並使用 AirPlay 播放音樂檔案或儲存在電腦(媒體伺服器)上的音樂檔案。大部分播放都 需要用行動裝置的 MusicCast CONTROLLER 應用程式。在行動裝置上安裝並 使用 MusicCast CONTROLLER 應用程式以播放音樂檔案。 使用 MusicCast CONTROLLER 應用程式連接 在行動裝置上安裝 MusicCast CONTROLLER 應用程式,將本機連接至網路並 登錄為啟用 MusicCast 的裝置。 ● 在開始之前請先確認行動裝置已經連接至家用路由器。 ● 若要使用網路功能,本機、PC 以及行動裝置都必須連接到同一個路由器。 請確認網路參數(例如 IP 位址)是在設定選單中的 “Information” (p.
2 點選 “Setup”。 4 按住本機的 CONNECT 鍵直到前面板顯示器顯示 “CONNECT”,然後點選 “Next”。 當顯示如下的螢幕時,請依照螢幕上的指示配置網路設定。 1. 使用行動裝置上的 Home 按鈕回到主頁螢幕。 2. 從 “Settings” 中選擇 “Wi-Fi”。 3. 從 “CHOOSE A NETWORK…” 中選擇 “MusicCastSetup”。 4.
5 若要將本機登錄為啟用 MusicCast 的裝置,請配置下列項目。 位置名稱(“家”、“約翰的家” 等等) 本機安裝所在的房間名稱與照片 ● 如 果 已 經 使 用 MusicCast CONTROLLER 應 用 程 式 登 陸 了 不 同 的 啟 用 (設定),然後選擇 “Add New MusicCast 的裝置,點選房間選擇螢幕的 Device” 將本機加入應用程式。 位置名稱以及本機安裝所在的房間名稱與照片可在之後變更。 點選 現在完成 MusicCast CONTROLLER 應用程式的網路連接,而且本機也已經登 錄為啟用 MusicCast 的裝置。 網路 網路功能與 MusicCast CONTROLLER 應用程式 52
使用 MusicCast CONTROLLER 應用程式之外的連接方式(無線網路) 使用本機的設定選單在不使用 MusicCast CONTROLLER 應 用程式的情況下連接至無線網路。 3 搜尋無線路由器(存取點) (p.55) 手動設定無線連接 (p.57) )鍵。 TV 螢幕上顯示設定選單。 分享 iOS 裝置設定 (p.53) 使用 WPS 按鍵配置 (p.54) 按 SETUP( 4 5 使用 WPS PIN 碼 (p.
8 當顯示下列螢幕時,按 ENTER 鍵。 █ 使用 WPS 按鍵配置 只要推一下路由器(存取點)上的 WPS 按鈕,即可輕鬆地設定 一個無線連接。 1 2 3 按 鍵以開啟本機。 開啟 TV 並將 TV 的輸入切換至從本機顯示視訊(HDMI OUT 插孔;p.
7 使用 鍵以選擇 “WPS Button” 並按 ENTER 鍵。 █ 搜尋無線路由器(存取點) 找出並連接至附近的無線路由器(存取點)。 1 2 3 按 鍵以開啟本機。 開啟 TV 並將 TV 的輸入切換至從本機顯示視訊(HDMI OUT 插孔;p.30)。 按 SETUP( )鍵。 TV 螢幕上顯示設定選單。 8 4 按無線路由器(存取點)上的 WPS 按鍵。 當建立好連接,TV 螢幕將顯示 “Completed” 字樣。 如果顯示 “Not connected”,請按 ENTER 鍵以便從步驟 6 開始重複過程,或參閱下方資訊以嘗試另一種連接方 法。 5 6 使用 鍵以選擇 “Network” 並按 ENTER 鍵。 使用 鍵以選擇 “Network Connection” 並按 ENTER 鍵。 使用 鍵。 鍵以選擇 “Wireless (Wi-Fi)” 並按 ENTER ● 如果您的無線路由器(存取點)使用 WEP 加密或已啟用 路由器的 MAC 位址過濾器,WPS 鍵無法用於建立無 線連接。請參閱 “搜尋無線路由器(存取點)” (p.
7 使用 鍵。 鍵以選擇 “Access Point Scan” 並按 ENTER 10 使用 [ ]/[ ]:左右移動游標鍵。 [Space]:輸入一空格。 [BKSP]:向左刪除一個所選字元。 [DELETE]:刪除所選字元。 [CLEAR]:刪除所有輸入的字元。 [CANCEL]:取消字元輸入,並返回之前的螢幕。 TV 螢幕上出現可使用的存取點清單。 8 使用 鍵並按 ENTER 鍵以輸入保全金鑰。 鍵以選擇想要的存取點並按 ENTER 鍵。 TV 出現無線連接設定螢幕。 一旦輸入保全金鑰,選擇 “OK”,然後按 ENTER 鍵。本 機將返回在步驟 8 中所顯示的螢幕。 11 使用 鍵以選擇 “Connect” 並按 ENTER 鍵以開始 連接過程。 當建立好連接時,TV 螢幕會出現 “Completed” 字樣。 如果出現 “Not connected”,請按 ENTER 鍵以便從步驟 6 開始重複過程,或參閱下方資訊以嘗試另一種連接方 法。 9 按 ENTER 鍵。 ● 如果您的無線路由器(存取點)已配置,“Access Point Scan” 無法用於建立無線連接
█ 手動設定無線連接 7 使用 鍵以選擇 “Manual Setting” 並按 ENTER 鍵。 8 使用 鍵以選擇 “SSID”。 手動設定網路的 SSID (網路名稱)、加密方法和防護金鑰。 1 2 3 按 鍵以開啟本機。 開啟 TV 並將 TV 的輸入切換至從本機顯示視訊(HDMI OUT 插孔;p.
9 使用 SSID。 鍵並按 ENTER 鍵以輸入存取點的 12 使用 鍵並按 ENTER 鍵以輸入防護金鑰。 如果您在步驟 10 中選擇 “WEP”,請輸入 5 或 13 個字 串、或 10 個或 26 個十六進位制(以 16 為基數)數字。 如果您選擇非 “WEP” 其他方式,請輸入 8 至 63 個字 串、或 64 個十六進位制(以 16 為基數)數字。 ● 十六進位制(以 16 為基數)數字使用 0 到 9 和字母 a 到 f 的組合。字母不區分大小寫。 [ ]/[ ]:左右移動游標鍵。 [Space]:輸入一空格。 [BKSP]:向左刪除一個所選字元。 [DELETE]:刪除所選字元。 [CLEAR]:刪除所有輸入的字元。 [CANCEL]:取消字元輸入,並返回之前的螢幕。 一旦輸入防護金鑰,選擇 “OK”,然後按 ENTER 鍵。本 機將返回在步驟 8 中所顯示的螢幕。 10 使用 鍵以選擇 “Security” 和使用 [ ]/[ ]:左右移動游標鍵。 [Space]:輸入一空格。 [BKSP]:向左刪除一個所選字元。 [DELETE]:刪除所選字元。 [CLEAR]:刪除
█ 使用 WPS PIN 碼 8 3 按 鍵以選擇想要的存取點並按 ENTER 鍵。 TV 螢幕上出現本機的 PIN 碼。 使用無線路由器(存取點)登錄本機的 PIN 碼以建立連接。如 果無線路由器(存取點)支援 WPS PIN 功能,就可使用此程 序。 1 2 使用 鍵以開啟本機。 開啟 TV 並將 TV 的輸入切換至從本機顯示視訊(HDMI OUT 插孔;p.
直接將行動裝置連接至本機(Wireless Direct) 不使用無線路由器(存取點),直接將行動裝置連接至本機。 Wireless Direct 支援下列。 - 使用已安裝專屬的 MusicCast CONTROLLER 應用程式之 行動裝置操作本機。 - 使用 AirPlay 播放儲存在 iOS 裝置上的音樂檔案。 本機 行動裝置 4 5 6 7 使用 鍵以選擇 “Network” 並按 ENTER 鍵。 使用 鍵以選擇 “Network Connection” 並按 ENTER 鍵。 使用 鍵。 鍵以選擇 “Wireless Direct” 並按 ENTER 使用 法。 鍵選擇 “Security” 以及 鍵選擇加密方 ● Wireless Direct 不可和有線網路連接(p.27)或無線網路連 接(p.
9 使用 及 ENTER 鍵以輸入防護金鑰。 一旦輸入防護金鑰,選擇 “OK”,然後按 ENTER 鍵。螢 幕將如下方顯示。 請輸入 8 到 63 個字串、或 64 個十六進位制(以 16 為基 數)數字。 ● 十六進位制(以 16 為基數)數字使用 0 到 9 和字母 a 到 f 的組合。字母不區分大小寫。 ● 在繼續到下一個步驟前,請記錄以下資訊。在配置行 動裝置的 Wi-Fi 設定會需要這些資訊。 - TV 螢幕上顯示的 SSID。 [ ]/[ ]:左右移動游標鍵。 [Space]:輸入一空格。 [BKSP]:向左刪除一個所選字元。 [DELETE]:刪除所選字元。 [CLEAR]:刪除所有輸入的字元。 [CANCEL]:取消字元輸入,並返回之前的螢幕。 - 剛輸入的防護金鑰。 10 使用 鍵以選擇 “Save” 並按 ENTER 鍵以儲存設 定。 本設定已完成而且 TV 螢幕上將顯示 “Set the mobile device”。本機的功能如同一個存取點。 接著,配置行動裝置的 Wi-Fi 設定。 11 配置行動裝置的 Wi-Fi 設定。 有關行動裝置的設定詳情,請參閱行動裝置
播放儲存在媒體伺服器(PC/NAS)的音樂 可在本機播放儲存在 PC 上的音樂檔案或 DLNA 相容的 NAS。 媒體分享設定 ● 當使用無線網路連接時,音訊可能被中斷。在這種情況下,請使用有線網路 連接。 支援的檔案格式 檔案 取樣率(kHz) 聲道數量 無縫播放 WAV* 32 至 192 2 MP3 8 至 48 2 ‒ WMA 8 至 48 2 ‒ MPEG-4 AAC 8 至 48 2 ‒ FLAC 32 至 192 2 ALAC 32 至 96 2 AIFF 32 至 192 2 * 限線性 PCM 格式 ● 播放 FLAC 檔案,需要經由 PC 的 DLNA 安裝支援 FLAC 檔案分享的伺服器 軟體,或者使用支援 FLAC 檔案的 NAS。 ● 無法播放 Digital Rights Management (DRM)內容。 若要播放儲存在 PC 或 DLNA 相容 NAS 的音樂檔案,首先需要在每個音樂伺 服器配置媒體分享設定。 █ 對於已安裝 Windows Media Player 的 PC 本
播放音樂檔案 使用安裝在您行動裝置的 MusicCast CONTROLLER 應用程式播放音樂。 ● 在播放音樂檔案前,將本機登錄為啟用 MusicCast 的裝置。 1 使用 MusicCast CONTROLLER 應用程式選擇本機的房間(Room1 等)。 2 點選 3 遵照螢幕上的指示選擇歌曲。 (伺服器)。 網路 播放儲存在媒體伺服器(PC/NAS)的音樂 63
收聽網際網路廣播電台 能收聽來自全球的網際網路廣播電台。 ● 可能無法接收到某些網際網路廣播電台。 ● 本機使用 vTuner 網際網路廣播電台資料庫服務。本服務可能隨時終止,恕不另行通知。 網際網路廣播電台的播放 登錄喜愛的網際網路廣播電台 使用安裝在行動裝置的 MusicCast CONTROLLER 應用程式 以選擇一網際網路廣播電台。 指派網際網路廣播電台至遙控器的 NET RADIO 鍵,或將它 們儲存至 MusicCast CONTROLLER 應用程式書籤裡。 ● 在收聽網際網路廣播電台前,將本機登錄為啟用 MusicCast 的裝置。 1 使用 MusicCast CONTROLLER 應用程式選擇本機的房 間(Room1 等)。 2 點選 3 從 “Locations”、“Genres” 等選擇一電台。 (網路電台)。 █ 指派一電台至 NET RADIO 鍵 1 選擇想要的網際網路廣播電台。 2 按住 NET RADIO 1、2 或 3 鍵至少 3 秒鐘。 選擇已指派之網際網路廣播電台 1 按住已指派要的網際網路廣播電台之 NET RADIO1
█ 使用 MusicCast CONTROLLER 應用程式將電台加入書簽 1 選擇想要的網際網路廣播電台。 2 在播放螢幕上點選●●●然後點選 “Add Bookmark”。 點選 ● 使用 PC 上的 Web 瀏覽器存取 vTuner 網站(http://yradio.vtuner.com/)並 編輯書簽。 ● 進入 vTuner 網站時,會顯示一個對話框來輸入本機的 vTuner ID。請事 先在設定選單的 “Information” 中的 “Network” 確認 vTuner ID (p.
使用 AirPlay 播放音樂 使用 AirPlay 功能就可經由網路在本機播放 iTunes 或 iPod 音樂。 ● 本章節將“iPod touch”、“iPhone” 和 “iPad” 統稱為 “iPod”。“iPod” 是指 “iPod touch”、“iPhone” 和 “iPad”,除非另有指定。 ● 如果沒有可用的路由器,可使用無線連接將 iPod 直接連接至本機來進行播 放(Wireless Direct)。有關使用 Wireless Direct 的指示請參閱 p.
3 選擇一首歌曲並開始播放。 若要操作播放,請使用 iPod 的 Music 應用程式或 PC 的 iTunes。 前面板顯示器顯示 “AirPlay”,並開始播放。 ● 經由將設定選單中的 “Network Standby” (p.
播放儲存在行動裝置上的音樂 使用本功能可在網路上播放儲存在行動裝置上的音樂。 使用行動裝置以播放歌曲 使用安裝在行動裝置的 MusicCast CONTROLLER 應用程式操作音樂。 路由器 ● 在播放音樂檔案前,請將本機登錄為開啟 MusicCast 的裝置(p.
設定 設定選單 從設定選單可以指定本機的各種設定並調整。可用的選項為獲得最佳環繞聲效果的音束輸出方式、聲道音量控制及 HDMI 設 定。 TV 螢幕顯示設定選單並能進行操作(不能在前面板顯示器顯示)。有關在 TV 上顯示設定選單之指示,請參閱 “在 TV 上顯示選單 螢幕” (p.30)。 設定選單的設定 1 按 SETUP ( )鍵。 2 按 鍵以選擇選單,然後按 ENTER 鍵或 鍵。 重複這些步驟以顯示想要的選單。 按 鍵或 RETURN ( ● 按住 SETUP ( )鍵以便直接在螢幕上顯示 “OSD Language” (p.31, 85)。 ● 如果有本機可用的韌體更新,信封狀的圖示( )會出現 在設定選單裡(p.
設定選單清單 選單 IntelliBeam Beam Horizontal Angle Beam Travel Length Focal Length Image Location Channel Out Subwoofer Channel Level Sound 功能 自動優化音束及聲音設定。 自動優化音束設定。 自動優化聲音設定。 調整水平音束角度。 調整音束行程。 調整音束焦距。 調整右前與左前聲道的聲音位置。 指定前方聲道的輸出方法。 指定是否要有後方環繞聲道。 啟用/取消 My Surround 功能。 指定是否使用有線或無線連接來連接超重低音喇叭。 指定超重低音喇叭到聆聽位置的距離。 手動配對中央主機與超重低音喇叭。 頁次 35 35 35 72 72 73 74 75 75 76 76 76 76 調整每個聲道之音量。 77 選擇是否依照本機的音量調整動態範圍。 指定動態範圍。 指定環繞聲解碼器。 指定 Dolby Pro Logic IIx Music 參數。 指定當從主機分配聲音到其他啟用 MusicCast 裝置的音 訊輸出時間。 77 78 78 79 HDMI C
選單 設定 Bluetooth Transmission Bluetooth Device Search MAC Address Information Network Connection Network Function Information IP Address MAC Address Filter Network Standby Network Update Dimmer OSD Language Distance Unit Audio Video System DHCP, IP Address, Subnet Mask, Default Gateway, DNS Server (P), DNS Server (S) Filter, MAC Address 1–10 Perform Update 功能 啟用/取消 Bluetooth 功能。 開啟或關閉傳輸音訊至 Bluetooth 組件例如 Bluetooth 喇 叭的功能。 搜尋將要傳輸音訊的 Bluetooth 組件例如 Bluetooth 喇 叭。 顯示 Bluetooth 連接的 MAC 位址。 顯示本機的網路資訊。 選擇網路
Beam 當使用了 “IntelliBeam” 選單(p.
█ Focal Length 建議使用預設設定 “Center” (-0.5 m 或-1.5 ft)。 範例 有正焦距的 左前方聲道 有負焦距的 中央聲道 擴大最佳聆聽區域(甜蜜點)。 下圖顯示所有聲道的輸出如何聚焦在一個點上,然後在從那個點擴散出去。施 加負值(-)以擴大甜蜜點,或正值(+)縮小甜蜜點。 焦距 焦距 甜蜜點 ● “AUTO SETUP” (p.33)自動啟用比本機寬度更寬的最佳聆聽(甜蜜點)範圍。 設定 Front L, Front R, Surround L, Surround R 可調整範圍 -1.0 m 至+13.0 m (-3.5 ft 至+43.5 ft) 設定 Center 可調整範圍 -1.0 m 至+13.0 m (預設:-0.5 m)(-3.5 ft 至+43.5 ft (預設:-1.
█ Image Location Right 百分比愈高,中央聲道輸出的聲音就愈大。 一旦將 “Adjustment” 設定至 “On”,就可選擇此設定。 如果來自於左右聲道的聲音不自然,請先調整每個聲道的音量(p.
Channel Out Surround Back 指定是否呈現後方環繞聲道。 FL:左前 FR:右前 C:中央 SL:左環繞 SR:右環繞 SBL:左後環繞 SBR:右後環繞 指定每個聲道的輸出方式。 Front 指定音束或正常聲音是否從前方聲道輸出。 設定 輸出 “Beam” 聲音 輸出 “Stereo” 聲音 None 未使用後方環繞聲道播放聲音。使用來自於聆聽位置後方 的音束播放左及右環繞聲道音訊。 Yes 使用後方環繞聲道播放聲音。使用來自於聆聽位置後方的 音束播放左及右環繞聲道音訊。左及右環繞聲道音訊,使 用來自於前方聲道及聆聽位置後方的音束來輸出。這樣就 也可以從聆聽位置兩側聽到聲音。 Auto (預設) 根據用來播放選定的輸入訊號源的聲道數量,自動選擇是 否使用後方環繞聲道。 輸出 “Mix” 聲音 設定 Beam 音束從左前、右前及中央聲道輸出。 在播放電影之類的內容時,此設定可以有效的創造出比實 際聆聽房間尺寸更大的音場。 Stereo 沒有音束從左前、右前及中央聲道輸出。 前方聲道的音訊來自於螢幕方向。因此,此設定在享受現 場音樂視訊之類的音樂
█ Subwoofer My Surround 指定是否啟用 “My Surround”,即始在不適合使用音束播放環繞聲的房間,也 能重現一種環繞聲的感受。 設定 Off (預設) 取消 My Surround。 On 啟用 “My Surround”。即始在使用無法充分供應環繞聲效 果的音束播放環繞聲的環境,也能以良好的環繞聲感享受 音訊播放。 按遙控器上的 SURROUND 鍵,以使用 My Surround 功 能播放。 ● 使用 “My Surround”,在本機正前方建立聆聽位置以獲得更好的環繞聲感。 ● 當 “My Surround” 設定至 “On”,就會取消 CINEMA DSP。 實施或調整超重低音喇叭設定,例如連接方式以及超重低音喇叭與聆聽位置的 距離。 Bass Out 指定如何連接超重低音喇叭。 設定 Wireless (預設) 選擇無線連接中央主機與超重低音喇叭。 Wired 選擇使用超重低音喇叭訊號線(RCA 單音訊號線)以及系統 控制訊號線(3.
Sound █ Channel Level █ Adaptive DRC 調整每個聲道的音量以平衡輸出電平。使用來自每個聲道輸出的測試音來調整 音量以達到最佳平衡。 調整本機的音量與動態範圍以獲得最佳平衡。當選定 “On” 時,動態範圍調整 如下,在低音獲得最佳的聆聽,例如在夜間使用。 項目 當音量低時: Front L, Front R, Center, Surround L, Surround R, Subwoofer 縮小動態範圍。大的聲音會以較柔和的音量播放,而很難聽到的柔和聲音則以 較大的音量播放。 -20 ~ +20 當音量高時: 擴大動態範圍。柔和與大的聲音,來源聲音都不會調整音量播放。 輸出電平 ● 當 “Channel Out” 的 “My Surround” 設定至 “On” 時,可以配置下列項目 (p.
█ Dynamic Range 調整本機的動態範圍(最大和最小音量之間的差異)。 設定 Min/Auto Min:將動態範圍設定在可以低音量支援舒適聆聽的電平。 Auto:依照從輸入訊號收到的資訊設定動態範圍。 Standard 建議使用於一般家庭的動態範圍。 Max (預設) 輸出未經調整動態範圍的輸入訊號源之聲音。 設定 DPL Movie* (預設) DPL Music* DPL Game* Neo:6 Cinema Neo:6 Music 使用適合電影的 Dolby Pro Logic II 解碼器。 使用適合音樂的 Dolby Pro Logic II 解碼器。 使用適合遊戲的 Dolby Pro Logic II 解碼器。 使用適合電影的 DTS Neo:6 解碼器。 使用適合音樂的 DTS Neo:6 解碼器。 * 當 7.1 聲道音訊依照選定的 “Channel Out” 設定(p.75)輸出時,使用 Dolby Pro Logic IIX 環繞聲解碼器。 ● 當啟用立體聲播放模式(p.42)、My Surround (p.76)或目標播放模式(p.
█ DPLx Parameter Audio Delay (LINK) 調整 Dolby Pro Logic IIX Music 環繞聲解碼器參數。 當聲音從本機分配到其他啟用 MusicCast 的裝置時,指定本機的聲音輸出時間 是否要與其他啟用 MusicCast 的裝置同步。 ● 此設定只有在 “Matrix Decoder” (p.
HDMI 用於配置有關 HDMI 訊號與 HDMI 控制功能的設定。 █ HDMI 控制 █ TV Input 開啟或關閉 HDMI 控制(p.37)。 如果 TV 與 ARC 不相容(或是取消 ARC 功能),TV 訊號經由 TV (光纖數位)輸 入插孔(預設)輸入。本機輸入訊號源可改變至 AUX2 (同軸數位)或 AUX1 (類比) 輸入插孔。 設定 Off 取消控制功能。降低本機的待機能源消耗。 On (預設) 啟用控制功能。 ● 當使用支援音訊返回通道(ARC)的 TV (p.24),或是當使用 HDMI 訊號直通功 能(p.
Bluetooth 配置 Bluetooth 設定。 █ Bluetooth █ Device Search 啟用/取消 Bluetooth 功能。 選擇將傳輸音訊的 Bluetooth 揚聲器或耳機,並將本機無線連接至揚聲器或耳 機。 設定 Off 取消 Bluetooth 功能。 On (預設) 啟用 Bluetooth 功能 █ Transmission █ MAC Address 顯示 Bluetooth 連接的 MAC 位址。 自本機傳輸音訊至 Bluetooth 揚聲器或耳機。 設定 Off (預設) 無法傳輸音訊。 On 輸入至本機的音訊可傳輸至 Bluetooth 揚聲器或耳機。 設定 設定選單 81
Network 配置網路設定。 █ Information █ Network Connection 顯示本機的網路資訊。 選擇網路連接方法。 ● 依據網路連接的類型,顯示的選項會有所不同(有線/無線(Wi-Fi)/Wireless Direct)。 Status NETWORK 插孔的連接狀態 Connection 連接方式 MC Network MusicCast Network 的連接狀態 SSID 本機所連接的存取點 Security 網路的加密方法 MAC Address MAC 位址(Ethernet/Wi-Fi) IP Address IP 位址 Subnet Mask 子網路遮罩 Default Gateway 預設閘道的 IP 位址 DNS Server (P) 主 DNS 伺服器的 IP 位址 DNS Server (S) 副 DNS 伺服器的 IP 位址 vTuner ID 網際網路廣播電台(vTuner)的 ID 設定 Wired 當使用網路線(未附贈)將本機連接到網路時,請 選擇此選項。 Wireless (Wi-Fi)
█ IP Address █ MAC Address Filter 配置網路參數(例如 IP 位址)。 MAC 位址過濾器位址限制可用於操作本機的網路裝置。 當經由行動裝置的應用程式操作本機時,請指定裝置的 MAC 位址。 DHCP 選擇是否使用 DHCP 伺服器。 ● AirPlay 功能(p.66)或 DLNA 相容的裝置(p.
█ Network Standby 當操作網路裝置或 Bluetooth 組件時,可開啟或關閉控制本機的電源(Network Standby)功能。 設定 Off On (預設) 取消網路待機功能。 啟用網路待 機功能。 ● 本機關閉時,在下列撥放操作時會開啟。 - 使用 AirPlay 播放 - 播放儲存在 DLNA-相容網路附加儲存 (NAS)裝置的音樂檔案 ● 也可使用安裝在行動裝置的 MusicCast CONTROLLER 應用程式來開啟本機。 當本機關閉時將 Bluetooth 組件連接至本機,本 機會開啟。 ● 本機在 “Network Standby” 設定至 “On” 時所消耗的電力高於設定至 “Off” 時的電力。 █ Network Update 經由網路更新韌體。 Perform Update 在更新韌體後,可使用此選項。有關詳情,請參閱 “更新本機的韌體” (p.
Function █ Dimmer ● 按住 SETUP ( )鍵以便直接在 TV 螢幕上顯示 “OSD Language”。 ● 當使用支援 HDMI 控制功能的 TV 時,可能會自動變更這些設定。 調整前面板顯示器及指示燈的亮度。數值愈小,顯示器與指示燈愈暗。 設定 -2 (最暗)至 0 (最亮) (預設) ● 當 ● 顯示語系只能在 TV 螢幕上顯示的選單中選擇。前面板顯示器顯示的資訊是 以英文顯示。 █ Distance Unit 指示燈亮紅燈,不管設定是什麼,顯示器的亮度都會是最高的。 ● 當啟用 Eco 功能時,無法配置此功能(p.
Information 顯示輸入至本機之音訊和視訊訊號的資訊。 █ Audio █ System 顯示下列目前音訊輸入訊號的資訊。 顯示目前安裝到本機的韌體版本。 格式 數位音訊格式 聲道數量 輸入訊號包括的聲道數量--前方/環繞/低頻效果(LFE)。 範例:“3/2/0.1” 代表訊號包括 3 前方聲道、2 環繞聲聲道 和 LFE。 如果包括非前方、環繞聲和 LFE 聲道的訊號,可能會顯示聲 道的總數量。例如:“5.
設定每個輸入訊號源(選項選單) 配置與目前播放內容的輸入訊號源有關的功能。 TV 螢幕顯示選項選單,並使用螢幕操作。有關在 TV 顯示選項選單的說明請參閱 “在 TV 顯示選單螢幕” (p.
選項選單清單 選項 說明 輸入 Treble HDMI1– 3, TV, AUX1– 2, 調整高音(treble)的輸出電平。 Bluetooth, NET (例如網際網路廣播電台) Bass 調整低音(bass)的輸出電平。 HDMI1– 3, TV, AUX1– 2, Bluetooth, NET (例如網際網路廣播電台) Volume Trim HDMI1– 3, TV, AUX1– 2, 調整每個插孔的輸入電平以補 Bluetooth, NET 償音量的變化。 (例如網際網路廣播電台) Audio Delay 調整音訊與視訊播放之間的時 HDMI1– 3, TV, AUX1– 2 間差異。 Audio Assign 當選擇 HDMI 裝置作為輸入訊 號源,來自不同輸入訊號源的 HDMI1– 3 音訊會被指派至 HDMI 音訊。 █ Adjusting tones (Treble, Bass) █ 音訊延遲控制(Audio Delay) TV 影像有時會落後於聲音。可以使用此功能延遲聲音輸出使其與視訊影像同 步。 ● 只有當 “Audio Delay (LINK)” (
進階設定 進階設定可以更精準的配置本機的功能。例如,可指定最大音量而且也可取消上面板的 INPUT 鍵。 設定進階選單 1 2 按 4 鍵關閉本機。 按住上面板的 INPUT 鍵時,按下遙控器的 源。 使用 鍵在前面板顯示器顯示想要的選單,然後按 鍵或 ENTER 鍵。 鍵開啟電 ● 按 或 RETURN ( 5 使用 6 按 )鍵可回到前一個選單。 鍵變更設定。 鍵關閉本機。 當按下 鍵開啟本機時就會反映新的設定。 前面板顯示器顯示 “ADVANCED”。 ● 進階設定選單不會顯示在 TV 螢幕上。 3 放開上面板的 INPUT 鍵。 設定 進階設定 89
進階設定清單 選單 設定/可調整範圍 說明 TURN ON VOLUME OFF (未設定)(預設),1 至 70 當本機電源開啟時,設定初始音量。 當設定至 “OFF” 時,音量與本機關閉時相同。 MAX VOLUME 1 至 99,MAX (最大)(預設) 設定最大音量所以本機輸出的聲音不會出過限定的音量。 INPUT LOCK ON (取消 INPUT 鍵操作) OFF (啟用 INPUT 鍵操作)(預設) 選擇是否啟用本機的 INPUT 鍵。 PANEL LOCK ON (取消本機的按鍵操作) OFF (啟用本機的按鍵操作)(預設) 選擇是否啟用本機的按鍵操作(除了進階設定操作)。 IP INPUT POWER ON (啟用電源開啟) OFF (取消電源開啟)(預設) 選擇當本機關閉時,是否可以按下遙控器上的一個輸入選擇器鍵自動開啟本機。 AC ON STANDBY ON (進入待機模式)(預設) OFF (恢復失去電源之前的狀態) 當本機暫時失去電源(將 AC 電源插頭從牆壁插座拔除、停電等)後恢復 AC 電源時, 設定本機關閉電源。 MEMORY PROT
選單 FW UPDATE 2) INITIALIZE 2) 設定/可調整範圍 說明 01.02 (顯示韌體版本) Start OK? (韌體已經更新) 確認韌體版本/更新韌體。 INFO (初始化所有與網路無關的設定) NET INFO (初始化與網路有關的設定)* CANCEL (不要初始化)(預設) 將本機的參數重設置原廠預設值。當本機凍結時,藉由恢復預設值可解決問題。 * 如果選定 “INFO” 就會恢復下列配置。 ● Network Standby (p.84) ● Bluetooth (p.47) 初始化本機也會初始化 IntelliBeam 測量結果及儲存在系統記憶體中的設定。再次從 “IntlliBeam” 選單中執行 “AUTO SETUP” (p.
更新本機韌體 提供額外功能或產品改良的新韌體,將於需要時發布。如果 本機連接到網際網路,可以經由網路下載韌體和更新。 使用設定選單中之 “Network Update” 以 更新韌體 可使用下列方式更新本機的韌體。 當本機的新版韌體發行後首次開啟本機時,TV 螢幕上會顯示 韌體可更新的訊息。 ● 從設定選單之 “Network Update” 更新韌體。 ● 經由連接以儲存本機韌體更新的 USB 隨身碟更新韌體 (p.93)。 ● 使用已安裝專屬 MusicCast CONTROLLER 應用程式的行 動裝置更新韌體。依照 MusicCast CONTROLLER 指南操 作應用程式並更新韌體。 注意 ● 韌體更新期間,請勿操作本機或拔掉電源線或網路訊號 線。更新韌體至少約需 20 分鐘(依據您的網路連接速度 而定)。 ● 如果網路連接速度緩慢或本機連接至無線網路,可能會 因為網路連接情況而無法進行網路更新,此時,請使用 USB 隨身碟更新韌體(p.
4 按 ENTER 鍵。 TV 螢幕變黑並開始更新韌體。 當韌體更新時,前面板指示燈會顯示更新進度。 4 在進階設定選單選擇 “FW UPDAT” 並按 ENTER 鍵。 5 使用 鍵選擇 “Start OK?” 並按 ENTER 鍵。 開始韌體更新。 當韌體更新時,前面板顯示器會顯示更新進度。 顯示更新過程。 顯示更新進度。 5 當前面板顯示 “Success!” 時,按本機上面板上的 鍵。 6 韌體更新完成。 當前面板顯示 “Success!” 時,按本機上面板上的 鍵。 韌體更新完成。 ● 如果韌體更新失敗,請使用 重複程序。 鍵關閉本機,然後再開啟,並再次從步驟 1 ● 如果顯示 “XXXSumERROR”,表示網路通訊發生問題。請檢查通訊狀態, 使用 鍵關閉本機,然後再開啟,並再次從步驟 1 重複程序。 ● 如果韌體更新失敗,請使用 鍵關閉本機,然後再開啟,並再次從步驟 1 重複程序。如果韌體更新再次失敗,請確認 USB 隨身碟是否正確連接至 UPDATE ONLY 插孔。 使用 USB 隨身碟的連接更新韌體 ● 如果顯示下列任一訊息,表示更新期間發生問題。
附錄 故障排除 當本機不能正常工作時請參閱下表。如果遇到的問題沒有列示在下面,或如果下面的指示並沒有幫助,請關閉本機,拔下 AC 電源線,並就近連絡授權的 Yamaha 經銷商或服務中心。 一般 問題 原因 參閱 頁次 處理方法 本機不能正常工作。 內部微處理器因為外部電擊(例如閃電或過量靜電) 或低電壓電源供應被凍結。 從插座拔下 AC 電源線,並在 30 秒後再次插上。 當按 鍵時本機未能開啟,或 電源開啟後不久後關閉本機。 AC 電源線沒有牢固地連接到 AC 牆壁插座。 將 AC 電源線牢固連接到 AC 牆壁插座。 內部微處理器因為外部電擊(例如閃電或過量靜電) 或低電壓電源供應被凍結。 從插座拔下 AC 電源線,並在 30 秒後再次插上。 “PANEL LOCK” 設定至 “ON”。 設定至 “OFF” 。 內部溫度變得過高,過熱保護電路已被啟動。 等待約 1 小時以便本機冷卻下來,確認足夠的通風空間而且不 可用布覆蓋本機後重新開啟。 當啟用 Auto Power Standby 功能時,在下列任一 情形會自動關閉本機: 開啟本機電源並重新播放訊號源。如果 Auto
問題 原因 參閱 頁次 處理方法 輸入或輸出訊號線連接不正確。 正確連接訊號線。 25 未選擇適當的輸入訊號源。 使用輸入選擇器按鍵選擇適當輸入訊號源。 39 音量減小。 提高音量。 39 靜音。 按 MUTE ( )或 VOL (+-)以恢復音訊輸出,然後調整音量。 39 有本機無法播放的輸入訊號。 播放本機能重現訊號之訊號源。變更訊號源組件之系統設定。 110 “HDMI Audio Out” 設定至 “TV”。 設定至 “AMP”。 80 “HDMI Control” 設定至 “Off”。 當本機僅使用 HDMI 訊號線連接支援 ARC (Audio Return Channel)之 TV,設定 “HDMI Control” 至 “On”。 80 若要在 “HDMI Control” 設定至 “Off” 下使用本機,請使用光 纖數位音訊訊號線將 TV 的音訊輸出插孔連接到本機的 TV (光 纖數位)輸入插孔。 24 來自可控制 HDMI 功能的 TV 的聲音被設定從 TV 內建的揚聲器輸出。 使用 TV 的 HDMI 設定來設定音訊輸出到除了
問題 超重低音喇叭 沒有聲音。 參閱 頁次 處理方法 有線/無線 超重低音喇叭的 AC 電源供應線沒有牢固連接至 AC 牆壁插座。 將 AC 電源供應線牢固連接至 AC 牆壁插座。 有線/無線 超重低音喇叭的音量太低。 使用遙控器上的 SUB+鍵增加超重低音喇叭的音量。 有線/無線 啟動超重低音喇叭內建的保護電路。 (超重低音喇叭的 STATUS 指示燈亮橘燈)。 拔掉電源線,並就近聯絡 Yamaha 經銷商或服務中心進行修 理。 有線 “Subwoofer” 的 "Bass Out"設定至 “Wireless”。 將其設定至 “Wired” 。 有線 系統控制訊號線(3.
問題 超重低音喇叭的 有線 聲音斷斷續續。 無線 影像未顯示在 TV 螢幕上。 未顯示本機的選單螢幕。 原因 29 用於連接超重低音喇叭至本機的訊號線未牢固連接。 牢固連接訊號線。 無線通訊狀況不良,而且中央主機與超重低音喇叭沒 將超重低音喇叭移動靠近中央主機。 有穩定的連接。 如果問題持續,將超重低音喇叭移到 STATUS 指示燈持續亮綠 燈的地方。 - 如果本機與超重低音喇叭之間有如金屬家具之類的障礙物阻礙通 訊,請重新安排家具或是重新放置超重低音喇叭。 - 如果有像是微波爐或無線網路裝置之類會發出電磁波的裝置,請 將本機及超重低音喇叭搬離這些裝置。 - HDMI 訊號線未牢固連接。 正確連接 HDMI 訊號線 未正確配置 4K MODE。 依照 4K 訊號格式選擇 MODE 1 或 MODE 2。 90 TV 的輸入開關未正確設定。 設定 TV 的輸入訊號源至本機。 30 將本機遠離這類設備。 - “HDMI Control” 設定至 “Off”。 設定 “HDMI Control” 至 “On”。 80 TV 無法使用 HDMI 控制功能。 請參閱 T
Bluetooth 問題 接收 本機無法連接 至 Bluetooth 組件。 本機沒有聲音 或聲音斷斷續 續。 原因 參閱 頁次 處理方法 “Bluetooth” 設定為 “Off”。 將其設定至 “On”。 81 未選擇 Bluetooth 作為輸入訊號源。 選擇 Bluetooth 作為輸入訊號源。 48 連接其他 Bluetooth 組件。 終止目前 Bluetooth 連接,並連接至必須收到音訊的裝置。 要與本機配對的 Bluetooth 配接器等密碼不是 “0000”。 使用密碼為 “0000” 的 Bluetooth 配接器。 該裝置不支援 A2DP。 連接至支援 A2DP 的 Bluetooth 音訊組件。 本機與組件相距甚遠。 擺放 Bluetooth 組件,以便與本機距離小於 10 m (33 ft),並將 組件連接至本機。 附近有一輸出 2.
問題 傳輸 無法讓本機連 接至 Bluetooth 組 件。 Bluetooth 組 件沒有聲音或 聲音斷斷續 續。 原因 參閱 頁次 處理方法 “Bluetooth” 設定至 “Off”。 設定至 “On”。 81 “Transmission” 設定至 “Off”。 設定至 “On”。 81 連接其他 Bluetooth 組件。 該裝置不支援 A2DP。 終止目前的 Bluetooth 連接,並連接至必須收到音訊的裝置。 連接至支援 A2DP 的 Bluetooth 音訊組件。 本機與組件相距甚遠。 擺放 Bluetooth 組件,以便與本機距離小於 10 m (33 ft),並將 組件連接至本機。 附近有一輸出 2.
網路 問題 網路功能無作用。 原因 未正確取得網路參數(IP 位址)。 處理方法 參閱 頁次 啟用路由器上的 DHCP 伺服器功能,並將本機設定選單中的 “DHCP” 設定至 “On”。如果要手動配置網路參數,請檢查正 在使用的 IP 位址是網路中其他網路設備未使用的。 83 “Not connected” 與 “Wireless (Wi-Fi)” 配置一起顯示;無法連 接到無線路由器(存取點)。 啟用無線路由器的 MAC 位址過濾器。 使用 WPS 功能(“WPS Button” 和 “PIN Code”)和 “Access Point Scan”,“Not connected” 與 “Wireless (Wi-Fi)” 配置一起 顯示;無法連接到無線路由器 (存取點)。 無線路由器(存取點)不能廣播其 SSID。 使用 WPS 功能(“WPS Button” 和 “PIN Code”),“Not connected” 與 “Wireless (WiFi)” 配置一起顯示;無法連接到 無線路由器(存取點)。 無線路由器(存取點)使用 WEP 加密。 播放意外停止且檔案不能連續播 放。
問題 無法播放網際網路廣播電台。 原因 參閱 頁次 處理方法 所選擇的網際網路廣播電台目前不能用。 有可能是廣播電台的網路問題,或服務可能已經停止。稍後 再嘗試該電台或選擇另一電台。 所選擇的網際網路廣播電台目前未廣播。 一些網際網路廣播電台廣播在一天的特定時間未廣播。 稍後再嘗試該電台或選擇另一電台。 - 網路設備(例如路由器)的防火牆設定限制網路存 取。 請檢查網路設備的防火牆設定。網際網路廣播電台只有在通 過每個無線電台指定的連接埠時才能播放。依據廣播電台, 連接埠號碼會不同。 - 啟用本機的 MAC 位址過濾器。 在設定選單中的 “MAC Address Filter”,禁用 MAC 位址過濾 器或指定您的行動裝置的 MAC 位址,以允許它存取本機。 83 本機和行動裝置不在同一網路。 檢查網路連接和路由器設定,然後將本機和行動裝置連接到 同一個網路。 - 經由網路(Network Update)之韌 體更新失敗。 韌體更新可能因為網路狀況而無法完成。 再次經由網路(Network Update)來更新韌體或使用 USB 隨身 碟。 92 當使用 AirPl
前面板顯示器的訊息 訊息 參閱 頁次 說明 ViewScreen 本機的設定選單顯示於 TV 螢幕。使用 TV 螢幕來配置設定。 69 Key Locked 本機上的按鍵鎖住。使用遙控器。 89 Sleep XXmin Auto Power Standby 功能將在 XX 分鐘後關閉本機。 89 Protected SYSTEM MEMORY 1-3 及 NET RADIO 1-3 受到保護。 89 Disable 無法使用鍵盤操作。此訊息在下列情況下顯示。 ● 當取消 Bluetooth 功能。無法選定 Bluetooth 做為輸入訊號源。 48 ● 當使用目標播放模式時,無法調整聲道電平。 42 ● 當使用 My Surround 時,無法使用 CINEMA DSP 程式。 76 ● 當正在播放取樣率高於 48 kHz 的音訊訊號時,無法使用 CINEMA DSP 程式。 41 ● 當正在播放取樣率高於 48 kHz 的音訊訊號時,無法使用 Compressed Music Enhancer。 43 附錄 前面板顯示器的訊息 102
當環繞聲效果不夠時 本機透過投射自牆壁等反射的音束達到環繞聲效果。因為在音束路徑上的家具 等,或房間形狀的關係,音束有可能無法朝向聆聽位置。在這種情況下,聲音 可能變得不平衡。 安裝與調整聲音反射板 YRB-100 1 決定聲音反射板的位置。 如圖所示安裝聲音反射板。 ● 移動聲音反射板時務必握住支撐桿。 ● 使用設定選單中的 “Channel Level” (p.77)判定難以聽到聲音的精準方向。 圖 1. 理想狀態 圖 2. 因為沒有牆壁,無法反射環繞聲 (右)音束。 環繞聲右比環繞聲(左)安靜,或環繞聲 右在其應有的位置的前面。 建議的安裝位置 前方 大約 1.5 至 3 m (5 至 10 ft) 如果音束沒有反射至聆聽位置(圖 2),可以經由安裝選配的聲音反射板(YRB100)進行調整。 前方 安裝聆聽位置前方的面板, 以及環繞側面板的外側。 圖 3. 使用安裝的聲音反射板 環繞聲右的音束的正確的被反射且達 到正確的環繞聲音效。 聆聽位置 環繞側 安裝聆聽位置後方的面板, 以及前方面板的內側。 環繞側 大約 1 至 2.
2 使用進階設定(p.89)配置聲音反射板。 依據要被安裝的聲音反射板的位置,將 “YRB FL” (FL)、“YRB FR” (FR)、 “YRB SL” (SL)及 “YRB SR” (SR)設定至 “YES”。 彩條顯示穿過整個 TV 螢幕。當在步驟 4 判定面板的左右正確角度時,這 樣就可更容易辨識 TV 螢幕是否反射於面板上。 3 6 將 IntelliBeam 麥克風插入本機然後從 “IntelliBeam” 選單執行 “AUTO SETUP” (Beam+Sound optimize)(p.
配對中央主機與超重低音喇叭 ● 務必確認設定選單 "Subwoofer" 中的 "Bass Out" 設定至 “Wireless” (p.
環繞聲的基本常識 什麼是環繞聲? 什麼是數位聲音投影機? 環繞聲提供被聲音包圍的感覺,是在音樂廳和電影 院常見的一種體驗感。這可以透過眾多揚聲器圍繞 聆聽者與在各個方向均勻地輸出聲音來實現。這種 “環繞立體聲”技術使聽眾沉浸在所擺放揚聲器的聲 音中,不僅在聆聽者前方,而且在後方,及聆聽者 的兩側,使他或她感覺好像他們是在真正的音樂廳 或電影院。 數位聲音投影機分別控制安裝在整排的精巧揚聲 器,經過優化的音訊訊號從各個揚聲器輸出,並合 成高度集中的聲音(音束)。 為了獲得精確的方向控制和聲音重現的品質,聲音 必須拆分成獨立的音訊聲道以便輸出到各揚聲器。 一般家庭使用(7.1 聲道揚聲器系統)的環繞聲系統, 使用七支揚聲器和一支超重低音喇叭,產生環繞立 體聲,如下圖所示: 系統的聲像 數位擴大機 揚聲器 Yamaha 音訊技術 音束依目標方向散發 典型 7.
辭彙 音訊/視訊資訊 取樣率及位元深度 將類比音訊訊號進行數位化時,取樣率和位元深度表示資訊的數量。例如可能以 48 kHz/24 位元表示。 取樣率 定義每秒取樣的數量(在類比訊號中取樣一組有限的離散值)。當取樣率越高,可以播 放的頻率範圍更寬廣。 位元深度 當量化類比訊號為有限值時,定義聲音的振幅值。位元深度愈高,重現的聲音愈深 邃。 Deep Color Dolby TrueHD 由 Dolby Laboratories 所開發的一種先進的無損音訊格式,用於高解析光碟式媒體,以 提供錄音室品質的家庭劇院體驗。它可同時攜帶多達八個聲道的 96 kHz/24 位元音訊(多 達六個分離式聲道的 192 kHz/24 位元音訊),並廣泛使用於 Blue-ray 光碟片。 DTS Digital Surround DTS Digital Surround 是由 DTS 公司所開發支援 5.1 聲道音訊的壓縮數位音訊格式。廣 泛用於 DVD 光碟片。 DTS Express 這是用於 5.
網路資訊 SSID SSID (Service Set Identifier)是確認特定的無線 LAN 存取點的名稱。 Wi-Fi Wi-Fi 是一種技術,使用無線電波允許電子設備交換資料或連接到無線網路。 無線網路使用無線連接提供消除經由使用網線連接複雜性的優點。只有完整的 Wi-Fi Alliance 的互操作性測試產品可標示 “Wi-Fi Certified” 商標。 WPS WPS (Wi-Fi Protected Setup)是由 Wi-Fi Alliance 建立的一個標準,它可以輕鬆 建立無線家庭網路。 附錄 辭彙 108
規格 YSP-CU2700 WAV (限 PCM 格式) /AIFF/FLAC:最高至 192 kHz ● 電力消耗 .............................................................. 24 W 擴大機部分 ALAC:最高至 96 kHz ● 待機電力消耗 ● 額定輸出功率 高音喇叭(1 kHz, 1% THD, 4 Ω) ......................... 27.2 W ● 最大有效輸出功率 高音喇叭(1 kHz, 10% THD, 4 Ω) .......................... 32 W MP3/WMA/MPEG-4 AAC:最高至 48 kHz HDMI Control On, Network Standby Off ............. 1.8 W ● 網際網路廣播電台 HDMI Control Off, Network Standby On Wireless LAN (Wi-Fi) 揚聲器部分 ● Wireless LAN 標準 .........................
NS-WSW121 ● 驅動器 .......................14 cm (5-1/2 in) cone woofer x 1 非防磁型 ● INPUT 插孔 ................................................................ 1 █ HDMI 訊號 ● 視訊訊號 ● 音訊訊號 本機與下列視訊訊號相容。 音訊訊號類型 ● SYSTEM CONNECTOR 插孔 .................................... 1 ● 輸出功率 ..................... 75 W (100 Hz, 6 Ω, 10% T.H.D) ● 動態功率 ............................................................. 130 W ● 頻率響應 ............................................... 40 Hz - 500 Hz ● 無線 ● 電源供應 [澳洲機型] .....................
關於 GPL 說明 MusicCast 是 Yamaha Corporation 的商標或註冊 商標。 “ ” 品牌識別及 “Cinema DSP” 均為 Yamaha Corporation 之註冊商標。 Wi-Fi CERTIFIED Logo 是 Wi-Fi Alliance 的認證標 誌。 Wi-Fi Protected Setup Identifier Mark 是 Wi-Fi Alliance 的認證標誌。 Wi-Fi、Wi-Fi Alliance、Wi-Fi CERTIFIED、Wi-Fi Protected Setup、WPA 和 WPA2 是 Wi-Fi Alliance 的商標或註冊商標。 有關 DTS 的專利,請參閱 http://patents.dts.com。 經 DTS Licensing Limited 授權製造。 DTS、DTS-HD、符號&DTS 及符號都是 DTS, Inc. 的註冊商標。 © DTS, Inc.
索引 C 數字 2-channel playback 3D video 24 4K MODE 90 4K video 24 5.1ch 78 7.
MAC address filter 50, 83 Manual setting (wireless connection) 57 Matrix Decoder 78 Media sharing setup 62 Menu screen 30 Mobile device music 68 Movie 41 MP3 43 Music 41 MusicCast CONTROLLER app 5, 50 Network information 82 Network standby 84 Setup menu 69 Sharing Wi-Fi settings (iOS device) 31, 53 Sound optimize only 35 Sound output timing (MusicCast-enabled devices) Sound reflection board 103 SSID 55, 56, 82, 108 Stands 18 Stereo playback 42 Subnet mask 50, 82 Subwoofer connections 29, 105 Subwoofer set