Owner's Manual
Table Of Contents
- Owners Manual
- Table of Contents
- Features
- Supplied Accessories
- Parts & Controls
- Preparations
- Playback
- Basic operation for playback
- Enjoying sound based on your preference
- Playback with surround sound
- Enjoying three-dimensional surround sound (CINEMA DSP)
- 2-channel playback (stereo playback mode)
- Delivering sound to a specified location (target playback mode)
- Playing back digitally compressed formats (such as MP3, etc.) with enriched sound (Compressed Music Enhancer)
- Clear playback of human voices (CLEAR VOICE)
- Adjusting volume for each channel
- Adjusting tones
- Using useful features
- Wireless playback of audio via Bluetooth connection
- Networks
- Settings
- Troubleshooting
- Messages
- When surround effect is not enough
- Pairing the center unit and subwoofer
- Basic knowledge of surround sound
- Glossary
- Specs
- Index
- Quick Reference Guide
- MusicCast Setup Guide
- Supplement for Pandora
- Supplement for Rhapsody
- Supplement for Spotify
- MusicCast
- Mounting Template
- Scan of CD-ROM
- Warranty
PLAYBACK ➤ Using useful features En 46
Saving this unit’s settings to system memory
Three sets of settings can be saved to this unit’s memory, enabling
quick loading of settings optimized for specific listeners or
environmental changes as needed. Refer to the examples below to
save IntelliBeam measurement results and settings such as
surround setting to system memory, or to load a pre-defined
settings.
Example 1 Saving the IntelliBeam measurements for different
environments to system memory
If materials that absorb sound, such as curtains, obstruct sound
beams, the effectiveness of those beams decreases. Measure with
the curtains open and again with them closed. Save both sets of
settings to SYSTEM MEMORY 1 and 2, and load the appropriate
settings as needed.
Example 2 Saving frequently used settings to system memory
SYSTEM MEMORY 1: Surround setting
SYSTEM MEMORY 2: A target playback mode setting that
projects sound beams toward the kitchen
SYSTEM MEMORY 3: A target playback mode setting that
projects sound beams toward the living
room
Example 3 Saving preferred listener settings to system
memory
SYSTEM MEMORY 1: Settings configured for Dad
SYSTEM MEMORY 2: Settings configured for Mom
SYSTEM MEMORY 3: Settings configured for parties
The following settings can be saved to system memory.
• IntelliBeam measurement results (p. 33)
See page 35 for instructions on saving measurement results for
IntelliBeam.
(When “Horizontal Angle”, “Beam Travel Length”, “Focal Length”,
“Image Location”, and “Channel Level” are configured in the
setup menu (p. 69), these settings are applied to IntelliBeam’s
AUTO SETUP measurements.)
• Surround playback (p. 40), stereo playback (p. 42), or target
playback mode (p. 42)
(The Channel Out settings (p. 75) can also be saved for surround
playback mode.)
• Surround: CINEMA DSP (p. 41)
• Tone control (p. 44)
• Subwoofer settings (p. 76)
1
Hold down the SYSTEM MEMORY 1, 2, or 3 key until
“M1 Save?”, “M2 Save?”, or “M3 Save?”,
corresponding to the button pressed, is displayed.
2
Press the same SYSTEM MEMORY key again.
When the SYSTEM MEMORY 1 key is pressed, “M1
Saving” is displayed, and settings are saved.
• If system settings are already stored in the selected memory number, this
unit overwrites the old settings.
• The memory function cannot be set when “MEMORY PROTECT” is set to
“ON” in the advanced setup menu (p. 89).
1
Press the SYSTEM MEMORY 1, 2, or 3 key
corresponding to settings to be loaded.
If the SYSTEM MEMORY 1 key is pressed, “M1 Load?” will
be displayed.
2
Press the same SYSTEM MEMORY key again.
When the SYSTEM MEMORY 1 key is pressed, “M1
Loading” is displayed, and settings are loaded.
Saving settings to system memory
Loading settings
SYSTEM
MEMORY