OWNER'S MANUAL
CAUTION RISKOFELECTRICSHOCK DONOTOPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. • Explanation of Graphical l Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance the manufacturer's instmctious.
._l'.re]:|l-,VAvlllk'f:V._:ll'lhVl.'_l_|l.r_l[o]_, _ FCC INFORMATION (for US customers) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Compliance with FCC regulations does not guarantee that interference will not occur in all installations.
1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place with at least 5 cm (2 in) of space above (or below) this unit - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. 21 3 Locate this unit away from other electrical appliances, transformers to avoid humming sounds.
Overview .................................................................. Features ................................................................... Using this manual ................................................... Supplied accessories ............................................... Controls and functions ........................................... Front panel ................................................................. Front panel display ....................................................
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of surround sound experience as your local movie theater. Yamaha YSP-3050 Digital Sound Projector challenges this preconception that complicated speaker setup and troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
DigitalSoundProjectorTM The Digital Sound Projector Compatibility technology unit to control and steer multiple generate multi-channel surround allows one slim channels of sound to sound, thus eliminates the need for satellite loudspeakers and cabling normally associated with conventional surround sound systems. This unit also employs the beam modes that let you enjoy the surround sound (5 Beam, Stereo plus 3 Beam and 3 Beam), 2-channel and 5-channel stereo playback, and My Beam.
Ilr*-,lll_ inte\l/Beam The "tntelUBeam" logo and "IntelliBeam" are trademarks of Yamaha Corporation. The "_" logo and "Cinema DSP" are registered trademarks of Yamaha Corporation. DIGITAL Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-D symbol are trademarks of Dolby Laboratories. ® Manufactured under license from 1 Ltd. Worldwide patents applied for. The "_" of 1 Ltd. TruBass, SRS and the "(0) "symbol are registered trademarks of SRS Labs, Inc.
• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the supplied owner's manual for each component. • Operations in this manual use keys on the supplied remote control of this unit unless otherwise specified. • --',i,':indicates a tip for your operation. • This manual is printed prior to production. Designs and specifications are subject to change in part as a result of improvements, etc.
Check that you have received all of the following parts.
INPUT VOLUME ÷ STANDBY/ON 1 0) AUX 3 input jack _) VOLUME +/- Connect your portable audio player (see page 22). Controls the volume level of all audio channels (see page 41). (_ INTELLIBEAM MIC jack Connect the supplied IntelliBeam microphone for AUTO SETUP (see page 30). (_ Remote control sensor O STAN DBYION Turns on the power of this unit or sets it to the standby mode (see page 25). Receives infrared signals from the remote control.
Ilwml_'TJ'Tll|°||'|f|Pif|ql(, IIIU uln lull IllU ll;ll /ill| IIIII O TUNER input source is indicators XM: MEMORY (see page 51). CINEMA an FM broadcast flashes during the XM preset operation DSP indicator DSP program is selected (see PCM (Pulse Code indicators Light up when the corresponding (see page 58). (_) ENHANCER decoder operates is selected Displays the current volume level.
q_r_kla.llll*Jl#lJINelol#t_ (i) ANTENNA jack Connect the FM antenna (see page 23). (_) DOCK terminal Connect the Yamaha iPod universal dock (such as YDS10, sold separately) (see page 53). (_) AUX 1 AUDIO INPUT jacks Connect an external component via an analog connection (see page 20). (_) TV/STB AUDIO INPUT jacks Connect your TV, digital satellite tuner, or cable TV tuner via an analog connection (see pages 21).
This section describes the functions of the remote control used to control this unit. Some buttons marked with an asterisk (*) share the common functions between the YSP and TV/AV operation modes ((_). _%'.. @ Infrared window Outputs infrared control signals. Aim this window at the component you want to operate. Q STANDBY/ON Sets this system to the standby mode (see page 25).
,,llIIIIJ'e]l._]p;.llit||lll(ll|le]ll_ DVD player/VCR control buttons RETURN Control your DVD player or VCR (see pages 95 and 97). Returns to the previous SET MENU screen. _) My Beam microphone TV VOL +/Adjusts the volume level of your TV (see page 95). Collects the test tones from this unit when using the My Beam auto-adjust function (see page 63). (_ TV POWER Turns on or off the power of your TV (see page 95). AV POWER Turns on or off the power of the selected component (see pages 95 and 97).
E_r;11_I.'_.fip_-Iaqf|qlt' This section describes the functions of the remote control used to control FM, XM Satellite Radio, or iPod when the TV/AV mode is selected with the operation mode selector Q PRESET/TUNE FM: Switches between the preset search mode and the frequency search mode (see pages 43 to 46). (_ Numeric buttons FM, XM: Enter numbers. ® ® Cursor buttons _ I _ I _ I _, ENTER FM: Use ENTRY # (/x/_) to change the preset station number (1 to 8) or frequency level (see pages 43 to 46).
This section describes a suitable installation location to install this unit using a metal wall bracket, a rack or a stand. Depending on your installation environment, connections with external components can be done before installing this unit. We recommend that you temporarily place and arrange all components, including this unit, in order to decide which procedure should come first. Especially when you make a connection connection first before installation (see page 18).
• Installation examples Example 1 Install this unit as close to the exact center of the wall as possible. [ I I I I Example 2 Install this unit so that the sound beams can be reflected off the walls. I ! / /\ I ! Example 3 Install this unit as close to the exact front of your normal listening position as possible.
r_lffll_fpjj • Using a metal wall bracket You can use the optional metal wall bracket to mount this unit on the wall in your listening room. Metal wall bracket • Using a rack You can install this unit either above or under your TV in a commercially available rack. When this unit is installed above your TV I This unit TV YSP-3050 When this unit is installed under your TV SPM-K30 (Option) (mm) _%'.
This unit is equipped with the following types of audio/video input/output jacks/terminal: For audio • • • • input 2 optical digital 2 coaxial digital 2 sets of analog 1 universal dock For audio output • 1 subwoofer output jack input jacks input jacks input jacks terminal For video output • 1 analog output jack For audio/video output For video input • 1 composite video input jack • 1 set of component video input jacks • 1 HDMIoutputjack For audio/video input • 2 HDMI input jacks Use these TV tuner,
• O Cables used for connections • Affixing cables To prevent cables from becoming unplugged, place the supplied cable clamp with the open side facing upward, attach it to the rear panel of this unit in a suitable position, and then affix cables in the cable clamp.
_[D[olili['..IOll[elig This unit is equipped with 2 HDMI input jacks and 1 HDMI output jack. If your TV and other components have HDMI jacks, use HDMI cables for simpler and easier connections, and you can skip the connection procedures from page 19 to 21. If your TV has a built-in digital satellite tuner and an optical digital output jack, connect the optical digital output jack on your TV to the TV/STB OPTICAL DIGITAL IN jack on this unit.
_.]alJl:1_#[Olt_ For audio connection, connect the coaxial digital output jack on your DVD player/recorder to the DVD COAXIAL DIGITAL INPUT jack on this unit. When you connect this unit to your DVD/VCR combo player/recorder, connect the analog audio output jacks on your DVD/VCR combo player/recorder to the AUX 1 AUDIO INPUT jacks on this unit in addition to the coaxial digital audio connection.
|¶'ililI:PII|'tlI" If your component supports optical digital connections, connect the optical digital output jack on your component (e.g., DVD player/recorder) to the AUX 1 OPTICAL DIGITAL INPUT jack on this unit. If your component does not support optical digital connections, connect the coaxial digital output jack on your component to the AUX 2 COAXIAL DIGITAL INPUT jack on this unit. If your component does not support any digital connections, connect the analog audio output jacks on your component (e.
_,1-J_,VfpJiF For audio connection, connect the analog audio output jacks on your TV to the TV/STB AUDIO INPUT jacks on this unit. If your TV has an optical digital output jack, connect the optical digital output jack on your TV to the TV/STB OPTICAL DIGITAL INPUT jack on this unit. For video connection, connect the video input jack on your TV to the VIDEO OUT jack on this unit to display the OSD for easy viewing when you adjust the system parameters in SET MENU. .%',.
J[IV[I]IIII_I_|(ll|[_ Connect the analog audio output jack on your portable audio player to the AUX 3 input jack on the front panel of this unit. Connect the monaural input jack on your subwoofer to the SUBWOOFER OUT jack on this unit. This connection alone does not output sound from the connected subwoofer. To output sound from the connected subwoofer, turn on the power of your subwoofer and then run AUTO SETUP (see page 29) or select SUBWOOFER for BASS OUT in SUBWOOFER SET (see page 80).
_'*itl#l:l*lglolll. Connect the supplied FM antenna to the FM ANTENNA jack on this unit. FM indoor antenna (supplied) Rear panel of this unit I r F'_--_ It ANTENNA I_ AUDIO INPUT "-1" OUT "_ VIDEO INPUT "_[ _ II Q/®I,UXl _.pw®_ ®/®1® ®1 I / I s_e ovo / _ DOCK _ t e l The IR IN jack does not support normal external component connection. This is a control expansion terminal for commercial use only.
Remove the transparent sheet before using the remote control. Press and hold the /_ mark on the battery cover and then open the coven 2 The remote control transmits a directional infrared beam. Use the remote control within 6 m (20 ft) of this unit and point it toward the remote control sensor of this unit during operation. Insert the two supplied batteries (AA, R6, UM-3) into the battery compartment. Make sure you insert the batteries according to the polarity markings (+/-).
2 Press STANDBY/ON again to set this unit to the standby mode. When this unit is in the standby mode, only STANDBY/ON on the front panel or on the remote control is operational, and the other control buttons on the front panel or on the remote control are not operational until the power of this unit is turned on. Press STANDBY/ON to turn on the power of this unit. The volume level appears in the front panel display, and the current input source and beam mode are displayed.
This section describes how to display the OSD (on-screen parameters for your listening comfort of your own home. 1 room. Once this is complete, Check that the video input jack on your TV is display) of this unit on your TV screen and to set the you can enjoy real surround sound while watching TV in the 4 Set the operation mode selector to YSP. 5 Press MENU. connected to the VIDEO OUT jack on this unit to display the OSD of this unit. 2 Press STANDBWON to turn on the power of this unit.
pi.711P_.*l:lllArd:hVll The following diagram illustrates the overall flow of the setup procedure. Run LANGUAGE SETUP. See "Changing OSD language" on page 28. Run AUTO SETUP (IntelliBeam). See "AUTO SETUP (IntelliBeam)" on page 29. If an error occurs Look for a remedy. See "Error messages for AUTO SETUP" on page 35 for a complete list of error messages and possible remedies. Play back audio signals or adjust the settings for the beam mode and the CINEMA DSP.
This feature allows you to select the language of your choice that appears in SET MENU of this unit. 1 4 Set the operation mode selector to YSP. Press ,_ / _ to select the desired language, and press ENTER. 2 Press MENU. The SET MENU screen appears on your TV. Choices: ENGLISH (English), DEUTSCH (German), Franqais (French), ESPAlqOL (Spanish), ITALIANO (Italian), NEDERLANDS (Dutch), PyccKnfi (Russian) SET MENU ÷ ,HEMORV ,AUTO SETUP .
This unit creates a sound field by reflecting sound beams on the walls of your listening room and by broadening the cohesion of all the channels. Just as you would arrange the speaker position of other audio systems, you need to set the beam angle to enjoy the best possible sound from this unit.
W,_|lBgeJ_]_lgl]:,lll'flr_ll1:::w.lm_! The supplied IntelliBeam microphone collects and analyzes the sound that this unit produces in your actual listening environment. Follow the procedure below to connect the IntelliBeam microphone to this unit and make sure that the IntelliBeam microphone is placed in a proper location and that there are no large obstacles between the IntelliBeam microphone and the walls in your listening room.
.|llgeJk'}:lllJ:lilii_llll:x:_lli! Once the IntelliBeam microphone is firmly connected to this unit and properly placed in your listening room, follow the procedure below to start the AUTO SETUP procedure. You can also enter the AUTO SETUP procedure simply by pressing and holding AUTO SETUP for more than two seconds. In this case, this unit performs both of the beam optimization and sound optimization procedures.
W'.|lBg#J_"]_glP.ilITi_lll:l'._.lmJ! 3 • Make sure that your listening room is as quiet as possible while this unit is performing the AUTO SETUP procedure. • To achieve the best results possible, evacuate yourself from your listening room until the AUTO SETUP procedure is completed so that you may not obstruct the path of sound beams. SET MENU [a]/[v]:UP/[)own [EHTER]:EnteP • The control buttons used for SET MENU are displayed at the bottom of the screen.
, lll g#____ _ lll 5 Press a / _ to select BEAM+SOUND OPTIMZ, BEAM OPTIMZ only, or SOUND OPTIMZ only and then press ENTER. The following screen appears on your TV. 6 ".il lil r_il ll-_ : _.:. m l Check the following points once again before starting the AUTO SETUP procedure.
W_,111J[o]_.'l :l l |l "Jl rfl _J l tl gr:_. ; . ] 8 Check that the following screen is displayed on your TV. The results of the AUTO SETUP procedure are displayed on your TV. 9 Press ENTER to confirm the results or press RETURN to cancel the results. The following screen is displayed for two seconds and then disappears from your TV. Example I SHOW RESULT MEASUREMENT COMPLETE BEAM MODE AUTO SETUP COMPLETE < Please remove the MIC ?non the VSP and the listening Position.
..tEjgeJ_]qlgJJ'.Jrtl_l_llTa:=i,;l,! • Error messages for AUTO SETUP Before the AUTO SETUP procedure starts Error message Cause See Remedy page ERROR E-2 No MIC detected. MIC connection Please check The IntelliBeam microphone connected to this unit. is not Connect the lntelliBeam microphone this unit. to 30 and re-try. While the AUTO SETUP procedure is in progress If one of the errors listed below except E-1 is displayed, press RETURN.
3 Press/'ENTER. I _ to select MEMORY and press The following screen appearson your TV. You can save the current settings adjusted in SET MENU in the system memory of this unit. It is handy to save certain settings according to the varying conditions of your listening environment. For example, if there are curtains in the path of sound beams, the effectiveness of the sound beams will vary depending on whether the curtains are open or closed.
m4,._l|i_,IImt_.l,l_",lg_m_ii,lt_#mlelA 5 Press A / _ to select MEMORY1, MEMORY2, or MEMORY3 and press ENTER. The following screen appears on your TV. 2)HB'IORY SAUE You can recall the settings saved in "Saving page 36 according to the varying conditions listening environment. settings" of your on 1 Set the operation mode selector to YSP. 2 Press MENU. The SET MENU screen appears on your TV. MEMORY1 Save Flow ? SET MENU Push [ENTER] to Save ÷ .
IJl_llitOmll[_l_ir_lf_jjmjjI_jjf_la 4 Press/x ENTER. / _ to select LOAD and press 6 Press ENTER again. The new parameters saved as MEMORY 1, MEMORY2, or MEMORY3 are loaded. Once the The following screen appears on your TV. parameters are loaded, the display returns to the SET MENU screen. _l I "dl LOAD I,,MEMuR_, MEMORY! Loading ,o°- € I',:,HEI'IORY LOAD € ÷ MEHORYI r, IEMORY2 MEMORY3 ".ET MENU [_]/[T]:Select [ENTER]:Enter ÷ .MEMORY •AUTO SETUP .MANUAL SETUP .
• You can play back sound from the components connected to this unit simply by pressing INPUT on the front panel repeatedly or pressing one of the input selector buttons (TV/STB, DVD, AUXI, AUX2, AUX3, XM, or FM) on the remote control. The name of the selected input source and the type of corresponding input mode appear in the front panel display. Front panel operations Press INPUT on the front panel repeatedly to toggle between TV/STB, DVD, AUX1, AUX2, AUX3, XM, and FM.
lum,/_i Press FM/XM to listening to FM (see "FM tuning" on page 42) or XM Satellite Radio (see "XM TM Satellite Radio tuning" on page 47). Switch to the video input on your TV using the remote control supplied with the TV and display the DVD menu screen. FM/XM If necessary, turn down the volume of your TV until no sound is heard. Press AUX1 (or AUX2) to play back a component connected to the AUX 1 (or AUX 2) jack on the rear panel of this unit.
• Muting Press the sound MUTE to mute the sound. "AUDIO MUTE ON" appears in the front panel display, and the volume level indicator flashes. MUTE I-'IUD I0 r, IUTE ON -I ,i Flashes Press VOLUME +/- to increase or decrease the volume level. The numenc value of the volume level appears in the front panel display. Control range: MIN (minimum), 01 to 99, MAX (maximum) VOLUME or 2 Press MUTE again (or press VOLUME +1-) to resume the sound output.
There are two tuning methods: automatic and manual. Automatic tuning is effective when the radio signal is strong and there is no interference. If the radio signal is weak, tune into the FM station manually. You can also use the automatic and manual preset tuning features to store up to 40 stations in total (AI to E8:5 preset station groups with 8 preset station numbers each). When the operation mode selector is set to TV/AV,you can operate all FM functions.
,1|ri|fqllllll 4 Automatic tuning is effective when the radio station signals are strong and there is no interference. 1 Set the operation mode selector to TV/AV. ,, Press ENTRY # (AI_) once to begin automatic tuning. When this unit is tuned into an FM station, the TUNED indicator lights up and the frequency of the station appears in the front panel display. • Press/x to tune into a higher frequency. • Press _ to tune into a lower frequency.
_]J_|lllllllll 3 2 Press SEARCH repeatedly until the AUTO indicator disappears from the front panel display. Press FM/XM repeatedly to select FM as the input source. "FM" appears in the front panel display. FM/XM SEARCH jFH IZt LT o,-, ,.,o, 9 HH.7. i 3 NO colon (:) If a colon (:) appears in the front panel display, tuning is not available. Press PRESET/TUNE to turn the colon (:) off. 4 _.,$,,_ • Youcan also press INPUT on the front panel repeatedly to select FM as the input source.
|l_llqlllllJ 5 You can also store up to 40 stations (A1 to E8:5 preset station groups with 8 preset station numbers each) manually. 1 Set the operation mode selector to TV/AV. 2 Tune into the desired FM station. ENTRYO Flashes See page 43 for tuning instructions. 3 Press ENTRY € (AI_) to select a preset station number (1 to 8) while the MEMORY indicator is flashing. I 1 Press MEMORY. iimy _: F M The MEMORY indicator flashes in the front panel display for approximately 10 seconds.
|.,_|_|lllilliZd 4 You can tune into the preset stations simply by selecting the preset station groups and numbers. 1 Set the operation mode selector to TV/AV. Press ENTRY # (AI_) to select the desired preset station number (1 to 8). The preset station group and number appear in the front panel display together with the station band and frequency. ENTRYO ?,o. Press FM/XM repeatedly to select FM as the input source. :o.- "FM" appears in the front panel display. FM/XM fftl " F r'I '="=' t.m _w m .
• About XM Satellite XM Satellite Radio Radio offers an extraordinary variety of commercial-free music, plus the best in sports, news, talk, and entelxainment. XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.
Once you have installed XM Mini-Tuner Home Dock, inserted XM Mini-Tuner, connected Home Dock to your XM READY home audio system, and installed the antenna, you are ready to subscribe and begin receiving XM programming. There are three places to find your eight-character XM Radio ID: on XM Mini-Tuner, on XM Mini-Tuner package, and on XM Channel 0 (see "All Channel Search mode" on page 49). Record the XM Radio ID in the following eight squares for reference.
Sllrl__'_t_.'PTlr_llfli3gr.t+tr+]w.t#.n[, 3 Search for a desired channel by using one of the four XM Satellite Radio search modes: • To select a channel from all channels, see "All Channel Search mode" on this page. • To select a channel by channel category, see "Category Search mode" on this page. • To select a channel from the preset channels, see "Preset Search mode" on page 50. • To select a channel by directly entering the channel number, see "Direct Number Access mode" on page 50.
• Preset Search mode Direct Prior to selecting a preset channel in the Preset Search mode, you must preset the XM channels. For details, see "Presetting the XM TM Satellite Radio channels" on page 51. 1 Number Access mode Press SEARCH repeatedly to select either "ALL CH SEARCH" or "CAT SEARCH". SEARCH 1 Press SEARCH repeatedly to select "PRESET SEARCH". $ SEARCH XM ;ILL OH SE_RCH $ or t " PRESET SEI:IRL':H 2 Press CAT/A-Eo (<_I _) repeatedly to change the preset channel group (A to E).
._jr:"""_l_lllR:Jl.'h'Rtt_f.,.., 4 You can use this feature to store up to 40 XM Satellite Radio channels (A1 to E8:5 preset channel groups with 8 preset channel numbers each). You can then recall the preset channels easily by selecting the preset group and number as described in "Preset Search mode" on page 50. 1 Press ENTRY_ (A I _) repeatedly to select a preset number while the MEMORY indicator is flashing. The selected preset number appears in the front panel display.
D." f tr.J"_"__'_El i'_] lll FJl l l_[i jl'i]l l llil lll_ You can display the XM Satellite Radio information (channel number/channel name, channel category, and artist name/song or program title) for the currently selected channel in the front panel display or in the OSD. If a status or error message appears in the front panel display or in the OSD, see the "XM Satellite Radio" in "Troubleshooting" on page 100. • Displaying the XM channel • You can set the front panel display mode: CONT. or ONCE.
This unit has the DOCK terminal on the rear panel that allows you to connect the Yamaha iPod universal dock (such as YDS-10, sold separately). Station your iPod in the Yamaha iPod universal dock, and use the supplied remote control to operate your iPod. • Only iPod (Click and Wheel), iPod nano, and iPod mini are supported. • Some features may not be compatible depending on the model or the software version of your iPod.
",l-'-,-|li_lf I • For a complete list of status messages that appear in the front panel display and in the OSD, see the "iPod" section in "Troubleshooting"on page 100. • While your iPod is stationed in the YamahaiPod universal dock connectedto the DOCK terminal of this unit, your iPod battery is automatically charged as long as this unit is turned on.
.l.llll.m.,,ir,,, 4 Press _ I _ and <11t> to navigate through the iPod menu, and press ENTER to start playback of the selected song. and ..... I • Press RETURN or MENU to go back to the previous menu. • The informationon the current song also appears in the front panel display.Youcan set the front panel display mode: CONT. or ONCE. For details, see "SCROLL" (Front panel display scroll) in "F.DISPLAYSET" (Front panel display settings) (see page 83).
You can enjoy multi-channel surround sound by changing the beam mode using the beam mode buttons on the remote control. Select 5 Beam, Stereo plus 3 Beam, 3 Beam, or My Surround for multi-channel playback. • When ANGLE TO WALL OR CORNER is set in MANUAL SETUP (see page 76), 5 Beam and 3 Beam cannot be selected. • To enjoy 5 Beam, Stereo plus 3 Beam, or 3 Beam as the beam mode, you must perform AUTO SETUP or MANUAL SETUP so that the parameters best match your listening environment.
_(|_E_JrllllOB."illlil[_]lllfOIl.yoJIIIfl Outputs normal sound from the front left and fight channels and sound beams from the center and surround left and fight channels. This mode is ideal for watching live recordings on a DVD. Vocals and instrumental sounds can be heard close to the center of the listening position while sound reflections from the venue itself can be heard on your fight and left, giving you the feeling that you are sitting fight in front of the stage.
m.
_|_lrJlI[Om."IlIII[OIIIIItIL"[O]III[I 2 Press SUR. DECODE repeatedly (or press SUR. DECODE and then press <_/ [_) to switch between surround modes. This unit can decode 2-channel sources for 5. l-channel Choices: Neo:6 Cinema, Neo:6 Music, PRO LOGIC, playback so that you can enjoy a variety of surround sound effects by switching the surround mode.
_]i__l[lJrllllOl_"llldKOlllllel_.Ylllll[I 4 If you hear sound from your TV speakers, reduce the volume level of your TV until you can no longer hear any audio being output. To reduce the TV volume level, use the remote control supplied with your TV. You can enjoy analog audio signals output from your TV in real surround sound. Before performing the steps below,set the volume of this unit to 30. If necessary,adjust the volume level in step 5 below. 5 Press VOLUME +1- to adjust the volume level.
ifllt_a'Jt,t'm,.'_!tltDI!l.td'm."t.lfl|Id When Dolby Pro Logic II Music selected is PANORAMA Gives the front left and fight channel sound a You can configure the parameters for Dolby Pro Logic II Music and DTS Neo:6 Music to fine-tune the surround sound effect. wraparound effect, distributed throughout the entire surround sound field to give you an expansive feeling.
You can enjoy 2-channel and 5-channel stereo playback as the beam modes by pressing STEREO on the remote control. • When you play back Dolby Digital audio signals in the 2-channel or 5-channel stereo playback, the dynamic range becomes compressed. If the volume level decreases to the extreme, use other beam modes except My Beam. • When the 2-channel or 5-channel stereo playback is selected as the beam mode, the surround modes (see page 58) and the CINEMA DSP programs (see page 65) become ineffective.
You can improve listenability in a noisy environment by changing the beam mode to My Beam, which outputs sound beams directly toward the listening position in a single channel. In addition, My Beam is also ideal when you do not want the sound beams to be reflected on the walls in your listening room or when you do not want to disturb other people while enjoying music or movies at night.
You can adjust the beam angle manually while playing back an input source. This function is also ideal if the listening position is out of the operation guarantee range of the auto-adjust function. 1 Set the operation mode selector to YSP. 2 Press MY BEAM. "MY BEAM" is displayed in the front panel display. Press _ / [_ while "MY BEAM" is displayed to adjust the beam angle. Control range: L90 ° to R90 ° • Press <_repeatedly to increase the horizontal angle on the left side.
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from stereo or multi-channel sources. This unit is also equipped with a Yamaha CINEMA DSP (digital sound field processing) chip containing several sound field programs used to enhance your playback experience. Most of the CINEMA DSP programs are precise digital recreations of actual acoustic environments found in famous concert halls, music venues, and movie theaters.
You can select from three different CINEMA DSP programs (MUSIC, MOVIE, and SPORTS) depending on the type of source you want to enjoy. The CINEMA DSP indicator lights up in the front panel display when one of the CINEMA DSP programs is selected. • The CINEMA DSP programs are ineffective when My Surround (see page 57), stereo sound (see pages 62) and My Beam (see pages 63) is selected as the beam mode.
I,b'III[OB-"IO1111fIilir_JI'IIhlKOI!IIP_Ilil, • Turning off CINEMA DSP programs Turn off the CINEMA DSP programs if you want to enjoy the original sound without the CINEMA DSP program effect. 2 Press MUSIC, MOVIE, or SPORTS to select the desired CINEMA DSP program. MUSIC 1 MOVIE SPORTS Set the operation mode selector to YSP. _ 3 Press or _> or _ F,. / _. "DSP LEVEL" is displayed in the front panel display. 2 Press OFF to turn off the CINEMA DSP ENI_YO programs.
You can use the Music Enhancer of this unit to improve the sound nearest to the original depth and width of compression artifacts such as the MP3 format. 3 Press ENHANCER repeatedly to switch between the Music Enhancer levels (OFF, HIGH, and LOW). ENHANCER % EHH#HCER: H I=H ENHANCER: L Old Set the operation mode selector to YSP. ENHANCER: OFF The ENHANCER indicator lights up when "ENHANCER:HIGH" or "ENHANCER:LOW" selected. 2 Press ENHANCER to select the Music Enhancer.
The night listening enhancers are designed to improve listenability at lower volumes or at night. In addition, you can limit the volume level of the TV so that it will not vary suddenly to a great extent whenever the contents being broadcast change (i.e. due to commercials, etc.). The EQUAL indicator lights up in the front panel display when "TV EQUAL VOLUME" is selected. \ -- I / EQUAL/ I \ Lights up • Select NIGHT:CINEMA when watching films to reduce the dynamic range of film soundtracks and to ma
Use this feature to automatically set this unit to the standby mode after a specified period of time. The sleep timer is useful if you are going to sleep after a certain amount of time while this unit is still playing back a source. Each time you press SLEEP, the front panel display changes as shown below. SLEEP •-_SLEEP 120p_in J, SLEEP 90p_in ,I, t '_-71_ EEP 6_:'_p_ in J, SLEEP 3_'_r,_ ir, J, _SLEEP 1 OFF Set the operation mode selector to YSP.
rl-'lll p mlmra-'tr_lq.a mq_l Canceling the sleep timer 1 Set the operation mode selector to YSP. 2 Press SLEEP repeatedly until "SLEEP OFF" appears in the front panel display. SLEEP va. LEEP 3 NFF Wait for a few seconds without operating this unit to confirm the setting for the sleep timer. The SLEEP indicator disappears from the front panel display, indicating that the sleep timer is deactivated.
You can display the format and sampling frequency of the current input signal in the front panel display. 2 Press DISPLAY. The information on the current input signal is displayed as follows: DISPLAY € D.DGTL:4,'.:,'kHz or Set the operation mode selector to YSP. IHPUT SIGHQL DOLBY DGTL: 48kHz Dolby digital DOLBY DGTL DTS DTS PCM PCM Analog 32/44.1/48/64/ 88.2/96 kHz ANALOG When the input signal is unclear, "- --" is displayedfor the sampling frequency.
You can operate the following functions using the remote control supplied with your TV if this unit and an HDMI control-compatible TV (except some models) are connected via HDMI.
To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment parameters, initial as well as to make settings (indicated advanced in bold • You can save the settings optimized specific conditions of your listening environment (see page 37). under settings each for sound parameter) by the AUTO SETUP environment signals, sound to reflect procedure allows you to make settings • Make settings for the parameters and DISPLAY MENU.
3 Press _ / _ to select MANUAL SETUP and press ENTER. The following screen appears on your TV. Use the remote control to access and adjust each parameter. ,HFIHUI SETUP L ÷ I)SOUND MENU 2)BEAH MENU 3)INPUT MENU 4)DISPLAY MENU [A]/[_]:UP/Down [ENTER]:EnteP Youcan adjust the SET MENU parameters while the unit is reproducing sound. 1 Set the operation mode selector to YSP. 2 Press 4 PressAl_toselectasub ENTER. menuandpress MENU. The SET MENU screen appears on your TV.
m'_ra,,'Ff: R[-7:llIJ" ANGLE TO WALL OR CORNER Use to manually adjust the various parameters related to the sound beam output. SET MENU _ MANUAL SETUP _ BEAM MENU :,,BEHM MENU ,'_ _ "_ ÷ A_',SETTIHG PARAr,IETERS B>BEAM AD.IUSTHENT C) INAGE LOCATION Select FLAT TO WALL if this unit is installed in parallel with the wall in your listening room.
_p.|iVlll,.|l_lgl|li, Select ANGLE TO WALL OR CORNER if this unit is installed in the comer of your listening room. Adjust the width and length of your listening room as well as the distance of the listening position from this unit. • BEAM ADJUSTMENT (Beam adjustment) Use to manually adjust the various sound beam settings. We recommend that you select 5 Beam as the beam mode before adjusting these parameters (see page 56).
ImV_, v,,llv_.v_-1.-Ii qBEAM TRAVEL LENGTH (Beam travel length) A certain amount of delay must be applied to the sound from each channel so that all sounds can arrive at the listening position at the same time. This menu sets the distance that sound beams travel after being output and reflected off the wall until they arrive at the listening position and adjusts the delay applied to the respective channel. The lines in the illustration below indicate the distance. I t I I Choices: 0.3 m to 24.0 m (1.
IrAF.,Y@II[,.|Idl,P]_Igll TREBLE GAIN (Treble gain) Use to adjust the high-frequency channel. output level of each _%',_ If the reflection points of the front left and right or surround left and right sound beams are on curtain or other acoustically absorbent surfaces, you can achieve more effective surround sound by increasing the treble level for those sound beams.
l,_r-mu.a_.l_lriBASS OUT (Bass out) Use to manually adjust the various parameters related to the sound output. SET MENU -_ MANUAL SETUP --, SOUND MENU I>SOUND MEt, IV ÷ A)TOHE CONTROL B>SUBWOOFER SET C>HUTE LEVEL D>AUDIO DELAY E>ROOH EQ F>DD/DTS D_naMic G>TruBass [_]/[T]:UP/Down EEHTER]:Enter • TONE CONTROL Range CROSS OVER (Crossover) (Tone control) You can adjust the tonal quality of sound beams. - TREBLE .....
:_p. IAv l Ip.l IB."l,_ltlll . • AUDIO DELAY (Audio delay) Use to delay the sound output and synchronize it with the video image. This may be necessary when using certain LCD monitors or projectors. Choices: 0 to 160 msec D)QU[:,IO DELAY AUDIO DELAY ..... Or_sec [_]/[_] :Select [ENTER ]:Return • DD/DTS Dynamic Range (Dynamic range of Dolby Digital and DTS signals) Use to select the amount of dynamic range compression.
l,'_r;v,'|_,_Tqq_l q" Select COMPONENT to assign a component to the COMPONENT VIDEO INPUT jack of this unit. Choices: DVD, AUX1, AUX2, TV/STB Use to manually adjust the various parameters related to the audio and video input. SET MENU -_ MANUAL SETUP --_ INPUT MENU " 'lJT ,IHF MEHU + Q)INPUT ASSIGNMENT B)INPUT MODE C)INPUT TRIM D)INPUT RENAME E)HDMI SET F)XM ANTENNA LEUEL "rr ",i ,'i ,'7 R)IHF'UT b. II.i['IIlEt'IT ,:,' o COMPONENT ÷ Linel .... DUD ( DUD [.,I,.].
_F:;#IIPfq_'/:ll#]" • INPUT TRIM (Input trim) Use to adjust the input level of the input source. C:,:, INPUT TRiMI,'2 + TU/STB DUD • INPUT RENAME (Input rename) Use to change the name of the input source in the OSD and the front panel display. Press an input selector button (e.g., DVD) to select the component you want to change the name for and perform the following procedure. ANALOG .... 3.0dB D I G I TAL., -3. OdB DIGITAL..-3, OdB [:,)INPUT REHQME [h.
mmmr,_Pli-7:UlV • HDMI SET (HDMI settings) Use to change the HDMI audio/video output/input to match the connected component. Choices: SUPPORT AUDIO (Support audio), AUDIO SELECT (Audio select), VIDEO INFO (Video information), UP-SCALING (HDMI up-scaling), ASPECT RATIO (HDMI aspect ratio), HDMI CONTROL (HDMI control) b)RUDIO -,ELB;T i,m + HDMII -, TU/STB ......... (TU/STB) DUD ...........
?tr-,i#1I/.,laI.'/_H #1, • Select OFF to deactivate feature the HDMI up-conversion • Select THROUGH signals. • Select 480p (or 576p), 1080i, or 720p to up-scale analog video signals to 480p (or 576p), 1080i, or 720p of resolution.
Use to manually adjust the various parameters related to the display. SET MENU _ MANUAL SETUP --->DISPLAY MENU • OSD SET (OSD settings) Use to adjust the display position and to set the display time of the OSD. ri'r, SET B,U:,D ÷ OSD SHIFT .......... 4',:'DISPLA"/MENU ÷ A)F.DISPLAY B)OSD SET C)UHIT SET OSD DISPLAV SET [_]/[_] TIME,, : UP/Down [_I]/[l_] [ENTER ] : Return 0 ,ON : Sel [i] / [_r] : UP/Do_Jn [ ENTER ] : Enter OSD SHIFT (OSD shift) • F.
You can adjust the sound beam output level of each channel by using the test tone or the audio output being played back in each beam mode to achieve a more true-to-life surround sound experience. 3 You can use the test tone feature to output a test tone from each channel to manually balance the channel levels. Use this to set the channel levels so that the volume level of each channel is identical when heard from your listening position. Press A / _ to adjust.
IT_lS_ 5 .a. ml. r-_..rar*l,mY. |1(oL_ Press TEST when you have completed all 1 Set the operation mode selector to YSP. your adjustments. TEST 2 • All channel levels cannot be adjusted when the 2-channel or 5channel stereo playback (see page 62), My Beam (see page 63), or My Surround (see page 57) is selected as the beam mode. • "FRONT L/R" cannot be adjusted when Stereo plus 3 Beam is selected as the beam mode (see page 57).
ip#nlk'fltmroatnl_:.lltottel;'_r.ltt_" 3 Press Control 4 _ / [_ to adjust range: -10.0 the channel volume. dB to +10.0 dB Wait for a few seconds without unit when you have completed adjustment. operating this your • All channel levels cannot be adjusted when the 2-channel or 5channel stereo playback (see page 62), or My Surround (see page 57) is selected as the beam mode. • "FRONT L/R" cannot be adjusted when Stereo plus 3 Beam is selected as the beam mode (see page 57).
You can select the type of audio input signals of the selected input source according to your preference or the conditions of the input source. This function is available for TV/STB, DVD, AUX1, and AUX2. We recommend setting the input mode to AUTO in most cases. 3 Press INPUTMODE repeatedly to toggle between input modes. INPUTMODE % F ITIJ..
This unit has additional menus that are displayed in the front panel display. These menus offer additional operations to adjust and customize the way this unit operates. When "F.PANEL KEY" is set to "F.PANEL: OFF" (see page 92), STANDBY/ON on the front panel is ineffective. Use STANDBY/ON on the remote control instead to adjust the system parameters. 2 Follow the procedure below to enter the system parameters.
ON, OFF MEMORY PROTECT You can protect the settings you saved in the system memory of this unit from being accidentally erased or unwantedly changed. i =i _IE_I.R , ,l]'Y PROTECT MAX VOLUME MAX, 99 to 01, MIN Control step: 1 You can set the maximum volume level so that this unit will not output sound beyond the limited volume level. VaL r, IR,,., "' UOLIIr.IE . . SET J MAX, 99 to 01, OFF :Control step: 1 TURN ON VOLUME You can set the initial volume level when the power of this unit is turned on.
FACTORY PRESET RESET, CANCEL You can reset all of the parameters of this unit to the factory presets. This procedure completely resets ALL the parameters in SET MENU. After performing the following procedure you must run AUTO sound environment. I 7 SETUP again to match your surround F E:TORV PRESET Press STANDBY/ON on the remote control to set this unit to the standby mode. STANDBY/ON The new setting will be activated when you turn on the power of this unit next time. _%'..
In addition to controlling this unit, the remote control can also operate other AV components made by Yamaha and other manufacturers. To control other components, you must set up the remote control with the appropriate remote control codes and set the operation mode selector to TV/AV to change the control area. Depending on the external AV component you are using, you may not be able to operate the component with the remote control, even if a remote control code is set.
• Operating your TV Numeric buttons Set the operation mode selector to TV/AV, and press TV to select TV as the input source. The controlarea of the remote controlchangesto theTV operation mode. Selects a TV channel for playback. CH+ISwitches between the available TV channels. ® TV INPUT Switches the input source for your TV. TV POWER Turns on or off the power of your TV. TV INPUT1 Selectsthe input source of your TV. TV VOL +/- ® Adjusts the audio output level of your TV.
• Operating your DVD player/recorder Set the operation mode selector to TV/AV and press DVD to select DVD as the input source. The control area of the remote control changes to the DVD operation mode. • Operating your STB (CATV/Satellite tuner) Set the operation mode selector to TV/AV and press STB to select STB as the input source. The control area of the remote control changes to the STB operation mode. ® ® t ® O) Numeric buttons O) Numeric buttons Enter numeric digits.
"[:-]ll[O](:i[tiOllllte]|l';_]_ll[_:_ • Operating your VCR Set the operation mode selector to TVIAV and press AUX1 to select VCR as the input source. The control area of the remote control changes to the AUX1 operation mode. This operation is available when your VCR is connected to the AUX1 AUDIO INPUT jacks on this unit. ® Lt 0) Numeric buttons Enter numeric digits. @ CH+ISwitches between the available VCR channels. _) Operation buttons for VCR Operate your VCR, such as play and stop.
_(*-.li|[O](:_[KIIIII'_I|!II'.JJ Setting macros for the TV with the tuning capability The TV macro feature makes it possible to perform a series of operations with the press of a single button. For example, when you want to play a DVD, you would normally turn on the component, select DVD as the input source, and press the play button to start playback. The TV macro feature lets you perform all of these operations simply by pressing the DVD macro button.
_f=/n JJre.! t-=lr_olm i r t=JJ_ • Setting macros for the TV without tuning capability the • Operating i_l_, _ macros Press and hold CODE SET and press one of the input selector buttons to select the input Press and hold one of the input selector buttons for approximately two seconds to select the input source you want to operate macros for. source you want to set macros for. Proceed to step 2 while holding down CODE SET. The TV inputchangesat the sametime the input mode changes.
Refer to the chart below when this unit does not function or if the instruction contact the nearest • properly. If the problem below does not help, set this unit to the standby authorized Yamaha dealer or service center. you are experiencing mode, disconnect is not listed below the AC power supply cable, and General See Problem Cause This unit fails to turn on when STANDBY/ON Is pressed, or enters the standby mode soon after the power has been turned on. This unit suddenly standby mode.
fg.lqq[_-'llp,[*JuJt, Problem Cause BASS OUT in SUBWOOFER FRONT. No sound from the subwoofer. Remedy SET is set to See page 80 Select SUBWOOFER. The source does not contain low bass signals. Distorted or too little bass sound. CROSS OVER in SUBWOOFER SET is set One of the night listening enhancers currently selected. Too much bass sound. Set CROSS OVER correctly. incorrectly. TmBass is Turn off the night listening enhancers. Turn off TmBass. is currently turned on.
mllolrleT_'_##1ld • Remote control Problem Cause The remote control does not work and/or function properly. Cannot operate external components with the remote control of this unit. Remedy See page Wrong distance or angle. The remote control functions within a maximum range of 6 m (20 ft) and no more than 45 degrees off-axis from the front panel. 24 Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit.
|_*II, • XM Satellite Status Radio message CHECK ANTENNA Cause XM Mini-Tuner Remedy and Home Dock are not for the best reception level. I.IPDATI NG The XM u_r encryption updated. Wait until the encryption code is updated. NO S 1171HIZlL The signal is too weak. Adjust the orientation of the indoor antenna of Home Dock for the best reception level. LOAD ING It takes longer than four seconds to decode audio or text data.
• Dolby Digital Dolby Digital is a digital surround sound system that gives you completely independent multi-channel audio. With 3 front channels (left, center, and right) and 2 surround stereo channels, Dolby Digital provides 5 full-range audio channels. With an additional channel especially for bass effects, called LFE (low-frequency effect), the system has a total of 5.1-channels (LFE is counted as 0.1-channel).
_'llob'.l,.y_(|, • LFE 0.1-channel This channel is for the reproduction of low bass signals. The frequency range for this channel is 20 Hz to 120 Hz. This channel is counted as 0.1 because it only enforces a low-frequency range compared to the full-range reproduction by the other 5/6 channels in Dolby Digital or DTS 5.116.1-channel systems.
• Numerics 3 Beam ............................................................................ 5 Beam ............................................................................ • A AC power supply cable ................................................... Audio pin cable ............................................................... AUTO SETUP (IntelliBeam) ......................................... • 57 56 23 17 29 Battery ............................................................................
AMP SECTION FM SECTION • Maximum Output Power ................................................. • Tuning Range ...................................................... 2 W (1 kHz, 10% THD, 4 _) x 21 20 W (100 Hz, 10% THD, 4 f2) x 2 87.5 to 107.9 MHz GENERAL • Power Supply ......................................................... SPEAKER SECTION • Power Consumption AC 120 V, 60 Hz ................................................................. 36 W • Driver • Standby Power Consumption Small dia.
List of remote control codes PROSCAN PROTON TV ADMIRAL AIWA AKAI ALBA 292. 293, 216 294, 276, 283, 284 295,296 296 AOC BELL & HOWELL 297 BESTAR 298 BLAUPUNKT BLUE SKY BRANDT BROC SONIC BUSH 229, 222 298 223 297 296 BYD:SIGN CLATRONIC CRAIG 201.
RCA 744, 792, 793 SCIENTIFIC ATLANTA 752, 753,754, 789 SONY 756, 757 TOCOM 755 UNIVERSAL 769, 772, 773, 774, 775 VIEWSTAR 764, 766, 776, 777, 778, 779, 782 SATELLITE TUNER ECHOSTAR GE GENERAL 822 837,838, INSTRUMENT 839 823 HITACHI HUGHES JVC MAGNAVOX PANASONIC PHILLIPS PRIMESTAR PROSCAN RADIO SHACK RCA SAMSUNG SKY+ SKY HD SONY TOSHIBA UNIDEN ZENITH 824 843,844,845,846 822 825 826,829 825,843,844 845,846,847, 848,849 827 837,838,839,842 828 837,838,839,842 852 853 853 832,835 833,836 825 834 ii
OYAMAHA © 2008 YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, YAMAHA ELECTRONIK YAMAHA YAMAHA ELECTRONIQUE ELECTRONICS YAMAHA YAMAHA SCANDINAVIA A.B. MUSIC AUSTRALIA EUROPA G.m.b.N. SIEMENSSTR. 22-34, AVE., BUENA PARK, CALIF. ONTARIO M1S 3R1, CANADA 25462 RELLINGEN BEI HAMBURG, FRANCE S.A. RUE AMBROtSE CROIZAT BP70 CROISSY-BEAUBOURG (UK) LTD.
_,qst£t]i thi_ u_sJl in if}6 COmei' at a 40 a to 50 _' ari_Ie adjacem wa_s 4(P_¢_ !'0' ....,_ ,_ror_ _t_e ._#Q. i oy LI P]aoe this _nit in front of the rack. iZi - To • You elliOy can s_ppf_eg i2 Place finis unil upside down 3 _nStati, ihi_ an_1 connect _flis unit_o your T_ and DVD player/re_ord_r, be!le!" s[;rt'ouna aiso use ',he w_lh the rr, ela_ ei_eo_,s, op_'.oa__tmetal wall place _his w_.
_ ....
)VD p:a/ed_eco_de /¢'4 WIR _*7t _H 4s _>:' \,','s :{ ::_ :>:_ :(;A:, :x(_;_:4. :_'_:.tY: _,;, # f } ©F£ .
t_;__ } ou_ u e AU Assemble SCTUP t _ne cardboard micro snone 5 ana R Y Connect _ne [ne _ron_[ ar_e nteHiBeam _ Sel _me Intell Be_ r_ mKsrc }none rT_Ict_ophon@[8 _ne NT£LLIBEAM _:_you r_o_"_'_na_ t_st(_n_ng Ml( poslh( } _:,_ ........ 3TANDBY'ON remote con_ro_.
?% % ] foceGu t_@ }6 Press _:s_ _ _ :d AUTO SE:]'2 P_ess Checb me _oI!owing (£1£_ L£" _@CO@GS t-,:H _ L}4 _so__s ;ll sv,/_ 2 _'""T _s>(%,.}Y}R@ s o[ U']@ _f'/[@h/£'gsS_r ....
Se/ecl !.he 3 M_) L.M b@ ....... ©[8{I0 iuo_,.s S@I@C{C I[ s [_'VD ............ i_41'II(911=I (X}FIIIU Y}l{, Y F_t2 J_ f_e I.
EXCLUSIVES YOU'LL ONLY HEAR ON XM
YAMAHA Home Audio products are designed and manufactured to provide a high level of trouble-free performance. YAMAHA Electronics Corporation, USA, is proud of the experienced craftsmanship that goes into each and every YAMAHA Home Audio product. YAMAHA sells its Home Audio products only through a network of high quality, specially authorized dealers and is pleased to offer the following Limited Warranty, which applies only to products purchased from our authorized dealers.