manual
Table Of Contents
- English
- INTRODUCTION
- PREPARATION
- Installation
- Connections
- Before connecting components
- Connections using HDMI cables
- Connecting a TV
- Connecting a DVD player/recorder
- Connecting a digital satellite tuner or a cable TV tuner
- Connecting a digital airwave tuner
- Connecting a portable audio player
- Connecting other external components
- Connecting a subwoofer
- Connecting the FM antenna
- About the RS-232C/IR-OUT/IR IN terminals
- Connecting the AC power supply cable
- SETUP
- BASIC OPERATION
- Playback
- FM tuning
- Enjoying surround sound
- Enjoying stereo sound
- Playing back sound clearly (My Beam)
- Using sound field programs
- Using the music enhancer
- Using the volume mode (Night listening enhancer/TV volume equal mode)
- Using the sleep timer
- Displaying the input source information
- Using the HDMI control feature
- ADVANCED OPERATION
- ADDITIONAL INFORMATION
- Español
- INTRODUCCION
- PREPARACION
- Instalación
- Conexiones
- Antes de conectar componentes
- Conexiones usando cables HDMI
- Conexión de un TV
- Conexión de un reproductor/grabadora DVD
- Conexión de un sintonizador de satélite digital o un sintonizador de TV por cable
- Conexión de un sintonizador digital de ondas del aire
- Conexión de un reproductor de audio portátil
- Conexión de otros componentes externos
- Conexión de un altavoz de subgraves
- Conexión de la antena de FM
- Acerca de los terminales RS-232C/IR-OUT/IR IN
- Conexión del cable de alimentación de CA
- INSTALACION
- FUNCIONAMIENTO BASICO
- Reproducción
- Sintonización de FM
- Disfrute del sonido surround
- Disfrute del sonido estéreo
- Reproducción clara del sonido (My Beam)
- Uso de programas de campos sonoros
- Uso del realzador de música
- Utilización del modo de volumen (Modo de escucha nocturna/Modo de igualación del volumen del TV)
- Utilización del temporizador para dormir
- Visualización de información de la fuente de entrada
- Utilización de la función de control HDMI
- FUNCIONAMIENTO AVANZADO
- INFORMACION ADICIONAL
- 中文
- QUICK REFERENCE GUIDE
AUTO SETUP (IntelliBeam)
42 En
8 Check that the following screen is displayed
on your TV.
The results of the AUTO SETUP procedure are
displayed on your TV.
y
• If “ENVIRONMENT CHECK [FAILED]” is
displayed, we recommend running the AUTO SETUP
procedure again. For details, see step 9.
• If “SUBWOOFER : NOT APPLICABLE” is displayed
even though a subwoofer is connected to this unit,
increase the volume level of the subwoofer and run the
AUTO SETUP procedure again.
• Depending on the environment of your listening room,
the beam angle of front left and right, and surround left
and right may be set to the same value even if
“5 BEAM” is displayed as a result.
9 Press ENTER to confirm the results or press
RETURN to cancel the results.
The following screen is displayed for two seconds
and then disappears from your TV.
If “ENVIRONMENT CHECK [FAILED]” is displayed in
step 8, the following screen is displayed after pressing
ENTER. In this case, see ERROR E-1 in “Error messages
for AUTO SETUP” on page 43. Press ENTER to exit
AUTO SETUP and then run the procedure again from
step 3.
10 Disconnect the IntelliBeam microphone from
the INTELLIBEAM MIC jack on the front
panel.
y
If you want to save and load settings, see “Using the system
memory” on page 44.
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
SHOW RESULT
Example 1
MEASUREMENT COMPLETE
ENVIRONMENT CHECK[FAILED]
BEAM MODE :5 BEAM
SUBWOOFER :YES
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
SHOW RESULT
Example 2
←
Flashes
ENTER
AUTO SETUP COMPLETE
Please remove the MIC from
the YSP and the listening
position.
AUTO SETUP COMPLETE
Your YSP unit may not be set
up correctly.
We recommend you try again.
Please press [ENTER] key to
exit.
INTELLIBEAM MIC
AUX 3
←
Flashes