00cv_YSP-4000_UA.fm Page 1 Thursday, September 20, 2007 10:08 AM UA YSP-4000 YSP-4000 Digital Sound ProjectorTM © 2007 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY YAMAHA ELECTRONIQUE FRANCE S.A.
01EN_YSP-4000_UA.book Page i Wednesday, December 26, 2007 3:00 PM IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
01EN_YSP-4000_UA.book Page ii Wednesday, December 26, 2007 3:00 PM IMPORTANT SAFETY INSTRUCTIONS FCC INFORMATION (for US customers) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. Compliance with FCC regulations does not guarantee that interference will not occur in all installations.
01EN_YSP-4000_UA.book Page iii Wednesday, December 26, 2007 3:00 PM CAUTION: READ THIS BEFORE OPERATING THIS UNIT. Caution: Read this before operating this unit. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place with at least 5 cm (2 in) of space above (or below) this unit – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.
01EN_YSP-4000_UA.book Page 1 Wednesday, December 26, 2007 3:00 PM Contents Overview ................................................................. 2 Features .................................................................. 3 Using this manual .................................................. 5 Supplied accessories .............................................. 6 Controls and functions .......................................... 7 PREPARATION Installation ..............................................
01EN_YSP-4000_UA.book Page 2 Wednesday, December 26, 2007 3:00 PM Overview Overview It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of surround sound experience as your local movie theater.
01EN_YSP-4000_UA.book Page 3 Wednesday, December 26, 2007 3:00 PM Features Features My Surround In addition to the above mentioned beam modes, this unit is equipped with My Surround beam mode that allows you to enjoy surround system even in a small listening area. My Surround is a function integrated and optimized with DiMAGIC’s Euphony technology and Yamaha’s Beam reproduction system. My Beam This unit employs My Beam that ensures a clear sound in a noisy environment.
01EN_YSP-4000_UA.book Page 4 Wednesday, December 26, 2007 3:00 PM Features The “ ” logo and “IntelliBeam” are trademarks of YAMAHA CORPORATION. Manufactured under license from 1 Ltd. Worldwide patents applied for. The “ The “ ” logo and “Cinema DSP” are registered trademarks of YAMAHA CORPORATION. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories. ” logo and “Digital Sound Projector™” are trademarks of 1 Ltd.
01EN_YSP-4000_UA.book Page 5 Wednesday, December 26, 2007 3:00 PM Using this manual Using this manual 1 Install this unit in your listening room. See “Installation” on page 17. 2 Connect this unit to your TV and other external components. See “Connections” on page 20. 3 Prepare the remote control and turn on the power of this unit. See “Getting started” on page 32. 4 Run AUTO SETUP. See “AUTO SETUP (IntelliBeam)” on page 37. 5 Play back a source. See “Playback” on page 47.
01EN_YSP-4000_UA.book Page 6 Wednesday, December 26, 2007 3:00 PM Supplied accessories Supplied accessories Check that you have received all of the following parts. Remote control (×1) STANDBY/ON Fasteners (×4) Optical cable (×1) POWER POWER AV TV DOCK DVD AUX1 STB TV AUX2 AUX3 TV INPUT1 MACRO FM/XM PRESET/TUNE SEARCH CAT MEMORY AUTO VOL MODE SETUP INPUTMODE SLEEP 5BEAM ST+3BEAM 1 2 3 STEREO MY BEAM MY SUR.
01EN_YSP-4000_UA.book Page 7 Wednesday, December 26, 2007 3:00 PM Controls and functions Controls and functions INTRODUCTION Front panel AUX 3 INTELLIBEAM MIC INPUT 1 3 4 AUX 3 INTELLIBEAM MIC VOLUME + STANDBY/ON 2 5 6 INPUT VOLUME 7 + STANDBY/ON 1 Front panel display Shows information about the operational status of this unit. 6 VOLUME +/– Controls the volume level of all audio channels (see page 49). 2 Remote control sensor Receives infrared signals from the remote control.
01EN_YSP-4000_UA.book Page 8 Wednesday, December 26, 2007 3:00 PM Controls and functions Front panel display 2 1 890A B C 3 D 4 E 5 6 7 F 1 HDMI indicator Lights up when the signal of the selected input source is input at the HDMI IN jack(s). A NIGHT indicator Lights up when one of the night listening enhancers is selected (see page 71). 2 TUNER indicators FM: Light up when this unit is receiving an FM broadcast. XM: MEMORY flashes during the XM preset operation (U.S.A.
01EN_YSP-4000_UA.book Page 9 Wednesday, December 26, 2007 3:00 PM Controls and functions Rear panel The illustration below shows the rear panel of the U.S.A. and Canada models. DVD INTRODUCTION AUX 1 1 2 4 IN 5 3 (U.S.A. and Canada models) OUT HDMI IR-OUT IR-OUT 6 7 8 FM75 UNBAL.
01EN_YSP-4000_UA.book Page 10 Wednesday, December 26, 2007 3:00 PM Controls and functions C XM antenna jack (U.S.A and Canada models only) Connect your XM Mini-Tuner Dock (sold separately) (see page 5 in the Reference Guide). D IR IN terminal This is a control expansion terminal for commercial use only (see page 30). E RS-232C terminal This is a control expansion terminal for commercial use only (see page 30). F SYSTEM CONNECTOR terminal (U.S.A.
01EN_YSP-4000_UA.book Page 11 Wednesday, December 26, 2007 3:00 PM Controls and functions Remote control (Europe, Australia, Asia, and Korea models) y You can also control other components using the remote control once you set the appropriate remote control codes. See “Controlling other components” on page 104 for details.
01EN_YSP-4000_UA.book Page 12 Wednesday, December 26, 2007 3:00 PM Controls and functions F DVD player/VCR control buttons Control your DVD player or VCR (see pages 105 and 106). T RETURN Selects sleep timer settings or returns to the previous SET MENU screen. G My Beam microphone Collects the test tones from this unit when using the My Beam auto-adjust function (see page 63). U TV VOL +/– Adjusts the volume level of your TV (see page 104).
01EN_YSP-4000_UA.book Page 13 Wednesday, December 26, 2007 3:00 PM Controls and functions STANDBY/ON DVD AUX1 STB TV TV AUX2 AUX3 TV INPUT1 MACRO PRESET/TUNE SEARCH A-E 1 MEMORY FM AUTO VOL MODE SETUP INPUTMODE SLEEP 2 5BEAM ST+3BEAM 1 2 3 STEREO MY BEAM MY SUR. 4 5 6 MUSIC MOVIE SPORTS 7 8 0 ENTRY A-E ENTER 6 These functions are also available when this unit is receiving the Radio Data System (see page 54) or playing back your iPod (see page 3 in the Reference Guide).
01EN_YSP-4000_UA.book Page 14 Wednesday, December 26, 2007 3:00 PM Controls and functions Remote control (U.S.A. and Canada models) This section describes the functions of the remote control used to control this unit. Some buttons marked with an asterisk (*) share the common functions between the YSP and TV/AV operation modes (S). y You can also control other components using the remote control once you set the appropriate remote control codes. See “Controlling other components” on page 104 for details.
01EN_YSP-4000_UA.book Page 15 Wednesday, December 26, 2007 3:00 PM Controls and functions T RETURN Selects sleep timer settings or returns to the previous SET MENU screen. G My Beam microphone Collects the test tones from this unit when using the My Beam auto-adjust function (see page 63). U TV VOL +/– Adjusts the volume level of your TV (see page 104). H TV POWER Turns on the power of your TV or sets it to the standby mode (see page 104).
01EN_YSP-4000_UA.book Page 16 Wednesday, December 26, 2007 3:00 PM Controls and functions This section describes the functions of the remote control used to control FM, XM Satellite Radio, or iPod when the TV/AV mode is selected with the operation mode selector (7). STANDBY/ON POWER POWER AV TV DOCK AUX1 DVD AUX2 AUX3 TV INPUT1 MACRO TV STB FM/XM 1 PRESET/TUNE SEARCH CAT 5BEAM ST+3BEAM 1 2 3 STEREO MY BEAM MY SUR. 2 4 5 6 MOVIE SPORTS 7 8 OFF 0 CAT/ A-E 6 9 SUR.
01EN_YSP-4000_UA.book Page 17 Wednesday, December 26, 2007 3:00 PM Installation Installation This section describes a suitable installation location to install this unit using a metal wall bracket, a rack or a stand. Depending on your installation environment, connections with external components can be done before installing this unit. We recommend that you temporarily place and arrange all components, including this unit, in order to decide which procedure should come first.
01EN_YSP-4000_UA.book Page 18 Wednesday, December 26, 2007 3:00 PM Installation ■ Installation examples Example 1 Install this unit as close to the exact center of the wall as possible. Example 2 Install this unit so that the sound beams can be reflected off the walls. Example 3 Install this unit as close to the exact front of your normal listening position as possible. 18 En Black process 45.0° 240.
01EN_YSP-4000_UA.book Page 19 Wednesday, December 26, 2007 3:00 PM Installation ■ Using a metal wall bracket ■ Using a rack You can use the optional metal wall bracket (such as SPMK30) to mount this unit on the wall in your listening room. You can install this unit either above or under your TV in a commercially available rack.
01EN_YSP-4000_UA.book Page 20 Wednesday, December 26, 2007 3:00 PM Connections Connections This unit is equipped with the following types of audio/video input/output jacks/terminal: For audio input • 2 optical digital input jacks • 2 coaxial digital input jacks • 2 sets of analog input jacks • 1 universal dock terminal (U.S.A.
01EN_YSP-4000_UA.book Page 21 Wednesday, December 26, 2007 3:00 PM Connections Before connecting components ■ Cables used for connections ■ Affixing cables To prevent cables from becoming unplugged, place the supplied cable clamp with the open side facing upward, attach it to the rear panel of this unit in a suitable position, and then affix cables in the cable clamp.
01EN_YSP-4000_UA.book Page 22 Wednesday, December 26, 2007 3:00 PM Connections Connections using HDMI cables This unit is equipped with 2 HDMI input jacks and 1 HDMI output jack. If your TV and other components have HDMI jacks, use HDMI cables for simpler and easier connections, and you can skip the connection procedures from page 23 to 26.
01EN_YSP-4000_UA.book Page 23 Wednesday, December 26, 2007 3:00 PM Connections Connecting a TV For audio connection, connect the analog audio output jacks on your TV to the TV/STB AUDIO IN jacks on this unit. If your TV has an optical digital output jack, connect the optical digital output jack on your TV to the TV/STB OPTICAL DIGITAL IN jack on this unit.
01EN_YSP-4000_UA.book Page 24 Wednesday, December 26, 2007 3:00 PM Connections Connecting a DVD player/recorder For audio connection, connect the coaxial digital output jack on your DVD player/recorder to the DVD COAXIAL DIGITAL IN jack on this unit. When you connect this unit to your DVD/VCR combo player/recorder, connect the analog audio output jacks on your DVD/VCR combo player/recorder to the AUX 1 AUDIO IN jacks on this unit in addition to the coaxial digital audio connection.
01EN_YSP-4000_UA.book Page 25 Wednesday, December 26, 2007 3:00 PM Connections Connecting a digital satellite tuner or a cable TV tuner For audio connection, connect the optical digital output jack on your digital satellite tuner or cable TV tuner to the TV/ STB OPTICAL DIGITAL IN jack on this unit. Connect the analog audio output jacks on your digital satellite tuner or cable TV tuner to the TV/STB AUDIO IN jacks on this unit.
01EN_YSP-4000_UA.book Page 26 Wednesday, December 26, 2007 3:00 PM Connections Connecting a digital airwave tuner For audio connection, connect the TV/STB AUDIO IN jacks on this unit to the analog audio output jacks on your TV. Connect the optical digital output jack on your digital airwave tuner to the TV/STB OPTICAL DIGITAL IN jack on this unit in addition to the analog audio connection. By doing so, you can enjoy both analog and digital broadcasts.
01EN_YSP-4000_UA.book Page 27 Wednesday, December 26, 2007 3:00 PM Connections Connecting a portable audio player Connect the analog audio output jack on your portable audio player to the AUX 3 input jack on the front panel of this unit. Front panel of this unit AUX 3 INTELLIBEAM MIC INPUT VOLUME + STANDBY/ON PREPARATION AUX 3 Analog audio output Portable audio player Audio 3.5 mm stereo mini plug cable English 27 En Black process 45.0° 240.
01EN_YSP-4000_UA.book Page 28 Wednesday, December 26, 2007 3:00 PM Connections Connecting other external components If your component supports optical digital connections, connect the optical digital output jack on your component (e.g., DVD player/recorder) to the AUX 1 OPTICAL DIGITAL IN jack on this unit. If your component does not support optical digital connections, connect the coaxial digital output jack on your component to the AUX 2 COAXIAL DIGITAL IN jack on this unit.
01EN_YSP-4000_UA.book Page 29 Wednesday, December 26, 2007 3:00 PM Connections Connecting a subwoofer Connect the monaural input jack on your subwoofer to the SUBWOOFER jack on this unit. This connection alone does not output sound from the connected subwoofer. To output sound from the connected subwoofer, turn on the power of your subwoofer and then run AUTO SETUP (see page 37) or select SWFR for BASS OUT in SUBWOOFER SET (see page 82).
01EN_YSP-4000_UA.book Page 30 Wednesday, December 26, 2007 3:00 PM Connections Connecting the FM antenna Connect the supplied FM antenna to the FM ANTENNA jack on this unit. FM indoor antenna (supplied) FM75 UNBAL. COMPONENT ANTENNA SUBWOOFER COMPONENT Rear panel of this unit STB DVD/AUX 2 VIDEO IN AUX 1 About the RS-232C/IR-OUT/IR IN terminals The RS-232C, IR-OUT, and IR IN terminals do not support normal external component connections.
01EN_YSP-4000_UA.book Page 31 Wednesday, December 26, 2007 3:00 PM Connections Connecting the AC power supply cable Once all other connections are complete, plug one end of the AC power supply cable into the AC IN terminal of this unit and then plug the other end into the AC wall outlet. Rear panel of this unit (U.S.A. and Canada models) PREPARATION IR-OUT AC IN To the AC wall outlet English 31 En Black process 45.0° 240.
01EN_YSP-4000_UA.book Page 32 Wednesday, December 26, 2007 3:00 PM GETTING STARTED Getting started Installing batteries in the remote control y Remove the transparent sheet before using the remote control. Press Operation range of the remote control 1 Press and hold the mark on the battery cover and then open the cover. 2 Insert the two supplied batteries (AA, R6, UM-3) into the battery compartment. Make sure you insert the batteries according to the polarity markings (+/–).
01EN_YSP-4000_UA.book Page 33 Wednesday, December 26, 2007 3:00 PM Getting started Turning on this unit or setting it to the standby mode 2 Press STANDBY/ON again to set this unit to the standby mode. Note When this unit is in the standby mode, only STANDBY/ON on the front panel or on the remote control is operational, and the other control buttons on the front panel or on the remote control are not operational until the power of this unit is turned on.
01EN_YSP-4000_UA.book Page 34 Wednesday, December 26, 2007 3:00 PM USING SET MENU Using SET MENU Displaying the OSD (on-screen display) This section describes how to display the OSD (on-screen display) of this unit on your TV screen and to set the parameters for your listening room. Once this is complete, you can enjoy real surround sound while watching TV in the comfort of your own home.
01EN_YSP-4000_UA.book Page 35 Wednesday, December 26, 2007 3:00 PM Using SET MENU The flow chart of SET MENU The following diagram illustrates the overall flow of the setup procedure. Run LANGUAGE SETUP. See “Changing OSD language” on page 36. Run AUTO SETUP (IntelliBeam). See “AUTO SETUP (IntelliBeam)” on page 37. If an error occurs SETUP Look for a remedy. See “Error messages for AUTO SETUP” on page 43 for a complete list of error messages and possible remedies.
01EN_YSP-4000_UA.book Page 36 Wednesday, December 26, 2007 3:00 PM CHANGING OSD LANGUAGE Changing OSD language This feature allows you to select the language of your choice that appears in SET MENU of this unit. 1 Set the operation mode selector to YSP. 4 Press / to select the desired language, and press ENTER. TV/AV YSP ENTER ENTER 2 Press MENU. The SET MENU screen appears on your TV. SET MENU .
01EN_YSP-4000_UA.book Page 37 Wednesday, December 26, 2007 3:00 PM AUTO SETUP (INTELLIBEAM) AUTO SETUP (IntelliBeam) This unit creates a sound field by reflecting sound beams on the walls of your listening room and by broadening the cohesion of all the channels. Just as you would arrange the speaker position of other audio systems, you need to set the beam angle to enjoy the best possible sound from this unit.
01EN_YSP-4000_UA.book Page 38 Wednesday, December 26, 2007 3:00 PM AUTO SETUP (IntelliBeam) Installing the IntelliBeam microphone The supplied IntelliBeam microphone collects and analyzes the sound that this unit produces in your actual listening environment.
01EN_YSP-4000_UA.book Page 39 Wednesday, December 26, 2007 3:00 PM AUTO SETUP (IntelliBeam) Using AUTO SETUP (IntelliBeam) Once the IntelliBeam microphone is firmly connected to this unit and properly placed in your listening room, follow the procedure below to start the AUTO SETUP procedure. You can also enter the AUTO SETUP procedure simply by pressing and holding AUTO SETUP for more than two seconds. In this case, this unit performs both of the beam optimization and sound optimization procedures.
01EN_YSP-4000_UA.book Page 40 Wednesday, December 26, 2007 3:00 PM AUTO SETUP (IntelliBeam) 3 Notes • Make sure that your listening room is as quiet as possible while this unit is performing the AUTO SETUP procedure. • To achieve the best results possible, evacuate yourself from your listening room until the AUTO SETUP procedure is completed so that you may not obstruct the path of sound beams. • Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure.
01EN_YSP-4000_UA.book Page 41 Wednesday, December 26, 2007 3:00 PM AUTO SETUP (IntelliBeam) 5 Press / to select BEAM+SOUND OPTIMZ, BEAM OPTIMZ only, or SOUND OPTIMZ only and then press ENTER. The following screen appears on your TV. 6 Check the following points once again before starting the AUTO SETUP procedure.
01EN_YSP-4000_UA.book Page 42 Wednesday, December 26, 2007 3:00 PM AUTO SETUP (IntelliBeam) 8 Check that the following screen is displayed on your TV. The results of the AUTO SETUP procedure are displayed on your TV. 9 Press ENTER to confirm the results or press RETURN to cancel the results. The following screen is displayed for two seconds and then disappears from your TV.
01EN_YSP-4000_UA.book Page 43 Wednesday, December 26, 2007 3:00 PM AUTO SETUP (IntelliBeam) ■ Error messages for AUTO SETUP Before the AUTO SETUP procedure starts Error message ERROR E-2 No MIC detected. Please check MIC connection and re-try. Cause The IntelliBeam microphone is not connected to this unit. Remedy Connect the IntelliBeam microphone to this unit. See page 38 While the AUTO SETUP procedure is in progress If one of the errors listed below except E-1 is displayed, press RETURN.
01EN_YSP-4000_UA.book Page 44 Wednesday, December 26, 2007 3:00 PM USING THE SYSTEM MEMORY Using the system memory Convenient usage of the system memory 3 You can save the current settings adjusted in SET MENU in the system memory of this unit. It is handy to save certain settings according to the varying conditions of your listening environment.
01EN_YSP-4000_UA.book Page 45 Wednesday, December 26, 2007 3:00 PM Using the system memory 5 Press / to select MEMORY1, MEMORY2, or MEMORY3 and press ENTER. The following screen appears on your TV. ENTER ENTER Loading settings You can recall the settings saved in “Saving settings” on page 44 according to the varying conditions of your listening environment. 1 Set the operation mode selector to YSP. TV/AV YSP 2)MEMORY SAVE 2 Press MENU. The SET MENU screen appears on your TV.
01EN_YSP-4000_UA.book Page 46 Wednesday, December 26, 2007 3:00 PM Using the system memory 4 Press / to select LOAD and press ENTER. The following screen appears on your TV. 6 Press ENTER again. The new parameters saved as MEMORY1, MEMORY2, or MEMORY3 are loaded. Once the parameters are loaded, the display returns to the SET MENU screen. 1)MEMORY LOAD ENTER ENTER MEMORY1 Loading ENTER 1)MEMORY LOAD . MEMORY1 MEMORY2 MEMORY3 SET MENU p p [ ]/[ ]:Select [ENTER]:Enter .
01EN_YSP-4000_UA.book Page 47 Wednesday, December 26, 2007 3:00 PM PLAYBACK Playback Selecting the input source You can play back sound from the components connected to this unit simply by pressing INPUT on the front panel repeatedly or pressing one of the input selector buttons (TV, STB, DVD, AUX1, AUX2, or AUX3) on the remote control. The name of the selected input source and the type of corresponding input mode appear in the front panel display.
01EN_YSP-4000_UA.book Page 48 Wednesday, December 26, 2007 3:00 PM Playback Press AUX1 (or AUX2) to play back a component connected to the AUX 1 (or AUX 2) jack on the rear panel of this unit. 2 Switch to the video input on your TV using the remote control supplied with the TV and display the DVD menu screen. AUX1 Note If necessary, turn down the volume of your TV until no sound is heard. AUX1 AUTO 3 DVD Press AUX3 to play back a component connected to the AUX 3 input jack on the front panel.
01EN_YSP-4000_UA.book Page 49 Wednesday, December 26, 2007 3:00 PM Playback ■ Muting the sound Adjusting the volume TV VOL VOLUME CH MUTE TV INPUT TV MUTE CODE SET 1 Press MUTE to mute the sound. “AUDIO MUTE ON” appears in the front panel display, and the volume level indicator flashes. MUTE INPUT VOLUME + STANDBY/ON VOLUME CH TV VOL MUTE TV INPUT TV MUTE AUDIO MUTE ON Flashes Press VOLUME +/– to increase or decrease the volume level.
01EN_YSP-4000_UA.book Page 50 Wednesday, December 26, 2007 3:00 PM FM TUNING FM tuning There are two tuning methods: automatic and manual. Automatic tuning is effective when the radio signal is strong and there is no interference. If the radio signal is weak, tune into the FM station manually. You can also use the automatic and manual preset tuning features to store up to 40 stations in total (A1 to E8: 5 preset station groups with 8 preset station numbers each).
01EN_YSP-4000_UA.book Page 51 Wednesday, December 26, 2007 3:00 PM FM tuning Automatic tuning 4 Automatic tuning is effective when the radio station signals are strong and there is no interference. 1 Set the operation mode selector to TV/AV. Press ENTRY ( / ) once to begin automatic tuning. When this unit is tuned into an FM station, the TUNED indicator lights up and the frequency of the station appears in the front panel display. • Press to tune into a higher frequency.
01EN_YSP-4000_UA.book Page 52 Wednesday, December 26, 2007 3:00 PM FM tuning 3 Press SEARCH repeatedly until the AUTO indicator disappears from the front panel display. 2 Press FM to select FM as the input source. “FM” appears in the front panel display. FM SEARCH y • You can also press INPUT on the front panel repeatedly to select FM as the input source. • If “XM” appears in the front panel display, press FM/XM again to display “FM” (U.S.A. and Canada models only). A FM 88.
01EN_YSP-4000_UA.book Page 53 Wednesday, December 26, 2007 3:00 PM FM tuning y Manual preset tuning • If the colon (:) does not appear, press PRESET/TUNE to display the colon. • U.S.A. and Canada models use CAT/A-E . • Even when the operation mode selector is set to YSP, you can select the desired preset group by pressing A-E (CAT for U.S.A. and Canada models). You can also store up to 40 stations (A1 to E8: 5 preset station groups with 8 preset station numbers each) manually.
01EN_YSP-4000_UA.book Page 54 Wednesday, December 26, 2007 3:00 PM FM tuning Selecting a preset station You can tune into the preset stations simply by selecting the preset station groups and numbers. 1 Set the operation mode selector to TV/AV. 4 Press ENTRY ( / ) to select the desired preset station number (1 to 8). The preset station group and number appear in the front panel display together with the station band and frequency. ENTRY TV/AV YSP 2 ENTER Press FM to select FM as the input source.
01EN_YSP-4000_UA.book Page 55 Wednesday, December 26, 2007 3:00 PM FM tuning 1 Tune into the desired Radio Data System broadcasting station. We recommend automatic preset tuning to tune into the Radio Data System broadcasting stations (see page 52). Program type Descriptions NEWS News AFFAIRS Current affairs INFO General information SPORT Sport EDUCATE Education DRAMA Drama CULTURE Culture SCIENCE Science VARIED Light entertainment POP M Pop music ROCK M Rock music M.O.R.
01EN_YSP-4000_UA.book Page 56 Wednesday, December 26, 2007 3:00 PM ENJOYING SURROUND SOUND Enjoying surround sound You can enjoy multi-channel surround sound by changing the beam mode using the beam mode buttons on the remote control. Select 5 Beam, Stereo plus 3 Beam, 3 Beam, or My Surround for multi-channel playback. Notes • When ANGLE TO WALL OR CORNER is set in MANUAL SETUP (see page 78), 5 Beam and 3 Beam cannot be selected.
01EN_YSP-4000_UA.book Page 57 Wednesday, December 26, 2007 3:00 PM Enjoying surround sound Stereo plus 3 Beam Outputs normal sound from the front left and right channels and sound beams from the center and surround left and right channels. This mode is ideal for watching live recordings on a DVD.
01EN_YSP-4000_UA.
01EN_YSP-4000_UA.book Page 59 Wednesday, December 26, 2007 3:00 PM Enjoying surround sound Enjoying 2-channel sources in surround sound This unit can decode 2-channel sources for 5.1-channel playback so that you can enjoy a variety of surround sound effects by switching the surround mode. 2 Press SUR. DECODE repeatedly (or press SUR. DECODE and then press / ) to switch between surround modes.
01EN_YSP-4000_UA.book Page 60 Wednesday, December 26, 2007 3:00 PM Enjoying surround sound Enjoying TV in surround sound 4 If you hear sound from your TV speakers, reduce the volume level of your TV until you can no longer hear any audio being output. To reduce the TV volume level, use the remote control supplied with your TV. 5 Press VOLUME +/– to adjust the volume level. You can enjoy analog audio signals output from your TV in real surround sound.
01EN_YSP-4000_UA.book Page 61 Wednesday, December 26, 2007 3:00 PM Enjoying surround sound Adjusting surround mode parameters You can configure the parameters for Dolby Pro Logic II Music and DTS Neo:6 Music to fine-tune the surround sound effect. MUSIC MOVIE 7 8 OFF 0 SPORTS +10 ENTRY CAT/ A-E ENTER MENU TV/AV YSP DISPLAY RETURN (U.S.A.
01EN_YSP-4000_UA.book Page 62 Wednesday, December 26, 2007 3:00 PM ENJOYING STEREO SOUND Enjoying stereo sound You can enjoy 2-channel and 5-channel stereo playback as the beam modes by pressing STEREO on the remote control. Notes • When you play back Dolby Digital audio signals in the 2-channel or 5-channel stereo playback, the dynamic range becomes compressed. If the volume level decreases to the extreme, use other beam modes except My Beam.
01EN_YSP-4000_UA.book Page 63 Wednesday, December 26, 2007 3:00 PM PLAYING BACK SOUND CLEARLY (MY BEAM) Playing back sound clearly (My Beam) You can improve listenability in a noisy environment by changing the beam mode to My Beam, which outputs sound beams directly toward the listening position in a single channel.
01EN_YSP-4000_UA.book Page 64 Wednesday, December 26, 2007 3:00 PM Playing back sound clearly (My Beam) Using manual-adjust function You can adjust the beam angle manually while playing back an input source. This function is also ideal if the listening position is out of the operation guarantee range of the auto-adjust function. 1 Set the operation mode selector to YSP. TV/AV YSP 2 Press MY BEAM. “MY BEAM” is displayed in the front panel display.
01EN_YSP-4000_UA.book Page 65 Wednesday, December 26, 2007 3:00 PM USING SOUND FIELD PROGRAMS Using sound field programs This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from stereo or multi-channel sources. This unit is also equipped with a Yamaha CINEMA DSP (digital sound field processing) chip containing several sound field programs used to enhance your playback experience.
01EN_YSP-4000_UA.book Page 66 Wednesday, December 26, 2007 3:00 PM Using sound field programs ■ Sound field program descriptions You can select from the following sound field programs based on your listening preference when you play music, movie or sports sources. For details on how to switch between the available sound field programs, see page 67. Note There is only one sports sound field program available.
01EN_YSP-4000_UA.book Page 67 Wednesday, December 26, 2007 3:00 PM Using sound field programs CINEMA DSP programs You can select from three different CINEMA DSP programs (MUSIC, MOVIE, and SPORTS) depending on the type of source you want to enjoy. The CINEMA DSP indicator lights up in the front panel display when one of the CINEMA DSP programs is selected. ■ Music programs Select this CINEMA DSP program when you play back music sources.
01EN_YSP-4000_UA.book Page 68 Wednesday, December 26, 2007 3:00 PM Using sound field programs ■ Movie programs ■ Sports program Select this CINEMA DSP program when you play back movie sources, especially the ones encoded in Dolby Digital, DTS, or Dolby Surround. This program clearly reproduces dialog and sound effects, thus creating a broad and expansive cinematic space amid silence. Select this CINEMA DSP program when you play back sports sources.
01EN_YSP-4000_UA.book Page 69 Wednesday, December 26, 2007 3:00 PM Using sound field programs ■ Turning off CINEMA DSP programs Turn off the CINEMA DSP programs if you want to enjoy the original sound without the CINEMA DSP program effect. 2 Press MUSIC, MOVIE, or SPORTS to select the desired CINEMA DSP program. MUSIC 1 Set the operation mode selector to YSP. TV/AV YSP 2 7 3 MOVIE or 8 SPORTS or 9 Press / . “DSP LEVEL” is displayed in the front panel display.
01EN_YSP-4000_UA.book Page 70 Wednesday, December 26, 2007 3:00 PM USING THE MUSIC ENHANCER Using the music enhancer You can use the Music Enhancer of this unit to improve the sound nearest to the original depth and width of compression artifacts such as the MP3 format. MUSIC MOVIE 7 8 OFF SPORTS 9 SUR. DECODE +10 0 ENHANCER ENTRY 3 Press ENHANCER repeatedly to switch between the Music Enhancer levels (OFF, MIN, and MAX).
01EN_YSP-4000_UA.book Page 71 Wednesday, December 26, 2007 3:00 PM USING THE VOLUME MODE (NIGHT LISTENING ENHANCER/TV VOLUME EQUAL MODE) Using the volume mode (Night listening enhancer/TV volume equal mode) The night listening enhancers are designed to improve listenability at lower volumes or at night. In addition, you can limit the volume level of the TV so that it will not vary suddenly to a great extent whenever the contents being broadcast change (i.e. due to commercials, etc.).
01EN_YSP-4000_UA.book Page 72 Wednesday, December 26, 2007 3:00 PM USING THE SLEEP TIMER Using the sleep timer Use this feature to automatically set this unit to the standby mode after a specified period of time. The sleep timer is useful if you are going to sleep after a certain amount of time while this unit is still playing back a source. FM/XM PRESET/TUNE SEARCH CAT Each time you press SLEEP, the front panel display changes as shown below.
01EN_YSP-4000_UA.book Page 73 Wednesday, December 26, 2007 3:00 PM Using the sleep timer ■ Canceling the sleep timer 1 Set the operation mode selector to YSP. TV/AV YSP 2 Press SLEEP repeatedly until “SLEEP OFF” appears in the front panel display. SLEEP SLEEP 3 OFF Wait for a few seconds without operating this unit to confirm the setting for the sleep timer. The SLEEP indicator disappears from the front panel display, indicating that the sleep timer is deactivated.
01EN_YSP-4000_UA.book Page 74 Wednesday, December 26, 2007 3:00 PM DISPLAYING THE INPUT SOURCE INFORMATION Displaying the input source information You can display the format and sampling frequency of the current input signal in the front panel display. 7 8 OFF 2 9 SUR. DECODE +10 0 ENHANCER ENTRY CAT/ A-E ENTER MENU Press DISPLAY. The information on the current input signal is displayed as follows: DISPLAY TV/AV YSP DISPLAY RETURN VOLUME CH TV VOL MUTE TV INPUT TV MUTE D.
01EN_YSP-4000_UA.book Page 75 Wednesday, December 26, 2007 3:00 PM USING THE HDMI CONTROL FEATURE Using the HDMI control feature You can operate the following functions using the remote control supplied with your TV if this unit and an HDMI control-compatible TV (except some models) are connected via HDMI.
01EN_YSP-4000_UA.book Page 76 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP MANUAL SETUP To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment parameters, as well as to make advanced settings for sound signals, sound beams, digital input, and the OSD. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your own listening environment.
01EN_YSP-4000_UA.book Page 77 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP Using MANUAL SETUP 3 Use the remote control to access and adjust each parameter. MUSIC MOVIE 7 8 SPORTS 9 OFF 0 SUR. DECODE ENTER +10 ENHANCER ENTRY CAT/ A-E ENTER ENTER MENU TV/AV YSP DISPLAY VOLUME Press / to select MANUAL SETUP and press ENTER. The following screen appears on your TV. RETURN CH ;MANUAL SETUP TV VOL . 1)SOUND MENU 2)BEAM MENU 3)INPUT MENU 4)DISPLAY MENU (U.S.A.
01EN_YSP-4000_UA.book Page 78 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP BEAM MENU ANGLE TO WALL OR CORNER FLAT TO WALL Use to manually adjust the various parameters related to the sound beam output. SET MENU → MANUAL SETUP → BEAM MENU 2)BEAM MENU . A)SETTING PARAMETERS B)BEAM ADJUSTMENT C)IMAGE LOCATION p p [ ]/[ ]:Up/Down [ENTER]:Enter y You can adjust the sound beam output level of each channel in “Adjusting the audio balance” (see page 90).
01EN_YSP-4000_UA.book Page 79 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP • Select ANGLE TO WALL OR CORNER if this unit is installed in the corner of your listening room. Adjust the width and length of your listening room as well as the distance of the listening position from this unit. Listening position from the unit INSTALLED HEIGHT (Installed height of this unit) Use to adjust the installed height of this unit. Choices: 0.0 m to 3.0 m Initial setting: 1.
01EN_YSP-4000_UA.book Page 80 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP HORIZONTAL ANGLE (Horizontal angle) Use to adjust the horizontal angle of sound beams for each channel. By adjusting the horizontal angle of the sound beams, you can optimize the sound beam paths. A test tone is automatically output.
01EN_YSP-4000_UA.book Page 81 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP FOCAL LENGTH (Focal length) Use to set the distance from the front of this unit to the focal point of output for each channel to achieve an expansive feeling for each channel. The focal points except for the center channel should be set near the reflection points on the walls. The shorter the distance, the larger the expansion. TREBLE GAIN (Treble gain) Use to adjust the high-frequency output level of each channel.
01EN_YSP-4000_UA.book Page 82 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP ■ IMAGE LOCATION (Image location) OFF L C )ON R Use to manually adjust the various parameters related to the sound output. SET MENU → MANUAL SETUP → SOUND MENU 1)SOUND MENU . A)TONE CONTROL B)SUBWOOFER SET C)MUTE LEVEL D)AUDIO DELAY E)ROOM EQ F)DD/DTS Dynamic Range G)TruBass [ ]/[ ]:Up/Down [ENTER]:Enter p C)IMAGE LOCATION .
01EN_YSP-4000_UA.book Page 83 Friday, March 7, 2008 10:03 AM MANUAL SETUP ■ MUTE LEVEL (Muting level) C)MUTE LEVEL pMUTE ■ ROOM EQ (Room equalizer) Use to change the tonal qualities of your listening room when the unit is mounted on the wall. Choices: MOUNTING (Mount type), REFLECTING (Reflectivity type) E)ROOM EQ . MOUNTING;;;;;SHELF REFLECTING;;;NORMAL p [ ]/[ ]:Up/Down [ ]/[ ]:Sel [ENTER]:Return MOUNTING (Mounting type) Use to enhance medium to low range sounds.
01EN_YSP-4000_UA.book Page 84 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP ■ DD/DTS Dynamic Range (Dynamic range of Dolby Digital and DTS signals) Use to select the amount of dynamic range compression. This setting is effective only when the unit is decoding Dolby Digital and DTS signals. Dynamic range is the difference between the smallest sound that can be heard above the noise of the equipment and the biggest sound that can be heard without distortion.
01EN_YSP-4000_UA.book Page 85 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP ■ INPUT TRIM (Input trim) AUX1 AUX1 DVD DVD p ) C)INPUT TRIM 1/2 ) p . HDMI1;;;; ( HDMI2;;;; ( Use to adjust the input level of the input source. p p [ ]/[ ]:Up/Down [ ]/[ ]:Sel [ENTER]:Return . TV/STB DVD ANALOG;;;-3.0dB DIGITAL;;-3.0dB DIGITAL;;-3.0dB p p A)INPUTHDMI ASSIGNMENT 1/3 A)INPUTCOMPONENT ASSIGNMENT 2/3 .
01EN_YSP-4000_UA.book Page 86 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP ■ INPUT RENAME (Input rename) ■ HDMI SET (HDMI settings) Use to change the name of the input source in the OSD and the front panel display. Press an input selector button (e.g., DVD) to select the component you want to change the name for and perform the following procedure. Use to change the HDMI audio/video output/input to match the connected component.
01EN_YSP-4000_UA.book Page 87 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP VIDEO INFO (Video information) Use to display the video information of the current input signal. Choices: HDMI SIGNAL, HDMI RES., HDMI ERROR b)VIDEO INFO . HDMI SIGNAL;;;HDMI -> HDMI HDMI RES.
01EN_YSP-4000_UA.book Page 88 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP e)HDMI CONTROL OFF p ON XXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXX p [ ]/[ ]:Select [ENTER]:Return DISPLAY MENU Use to manually adjust the various parameters related to the display. SET MENU → MANUAL SETUP → DISPLAY MENU p 4)DISPLAY MENU . A)F.DISPLAY SET B)OSD SET C)UNIT SET • Select ON to enable the HDMI control.
01EN_YSP-4000_UA.book Page 89 Wednesday, December 26, 2007 3:00 PM MANUAL SETUP ■ OSD SET (OSD settings) Use to adjust the display position and to set the display time of the OSD. B)OSD SET . OSD SHIFT;;;;;;;;;;0 OSD DISPLAY TIME;;;ON p p p p [ ]/[ ]:Up/Down [ ]/[ ]:Sel [ENTER]:Return OSD SHIFT (OSD shift) Use to adjust the vertical position of the OSD. Adjust toward the – (minus) direction to raise the position of the OSD, and adjust toward the + (plus) direction to lower it.
01EN_YSP-4000_UA.book Page 90 Wednesday, December 26, 2007 3:00 PM Adjusting the audio balance Adjusting the audio balance You can adjust the sound beam output level of each channel by using the test tone or the audio output being played back in each beam mode to achieve a more true-to-life surround sound experience. Using the test tone 3 You can use the test tone feature to output a test tone from each channel to manually balance the channel levels.
01EN_YSP-4000_UA.book Page 91 Wednesday, December 26, 2007 3:00 PM Adjusting the audio balance 5 Press TEST when you have completed all your adjustments. 1 Set the operation mode selector to YSP. TV/AV TEST YSP 2 Notes • All channel levels cannot be adjusted when the 2-channel or 5-channel stereo playback (see page 62), My Beam (see page 63), or My Surround (see page 57) is selected as the beam mode. • “FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is selected as the beam mode (see page 57).
01EN_YSP-4000_UA.book Page 92 Wednesday, December 26, 2007 3:00 PM Adjusting the audio balance 3 Press / to adjust the channel volume. ENTER Control range: –10.0 dB to +10.0 dB 4 Wait for a few seconds without operating this unit when you have completed your adjustment. Notes • All channel levels cannot be adjusted when the 2-channel or 5-channel stereo playback (see page 62), or My Surround (see page 57) is selected as the beam mode.
01EN_YSP-4000_UA.book Page 93 Wednesday, December 26, 2007 3:00 PM Selecting the input mode Selecting the input mode You can select the type of audio input signals of the selected input source according to your preference or the conditions of the input source. This function is available for TV/STB, DVD, AUX1, and AUX2. y We recommend setting the input mode to AUTO in most cases. AV 3 TV DOCK DVD AUX1 STB TV AUX2 Press INPUTMODE repeatedly to toggle between input modes.
01EN_YSP-4000_UA.book Page 94 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters Adjusting the system parameters This unit has additional menus that are displayed in the front panel display. These menus offer additional operations to adjust and customize the way this unit operates. Note When “F.PANEL KEY” is set to “F.PANEL: OFF” (see page 100), STANDBY/ON on the front panel is ineffective. Use STANDBY/ON on the remote control instead to adjust the system parameters.
01EN_YSP-4000_UA.book Page 95 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters Setting the MEMORY PROTECT 4 You can protect the settings you saved in the system memory of this unit from being accidentally erased or unwantedly changed. Press / to switch between “PROTECT: ON” and “PROTECT: OFF”. ENTER 1 Repeat steps 1 to 3 in “Using the system parameters” on page 94. 2 Set the operation mode selector to YSP.
01EN_YSP-4000_UA.book Page 96 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters Setting the MAX VOLUME 5 You can set the maximum volume level so that this unit will not output sound beyond the limited volume level. 1 Repeat steps 1 to 3 in “Using the system parameters” on page 94. 2 Set the operation mode selector to YSP. Press level.
01EN_YSP-4000_UA.book Page 97 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters 3 Press / so that “TURN ON VOLUME” is displayed in the front panel display. ENTER Setting the MONITOR CHECK Use this feature to activate or deactivate the monitor check function of this unit. When this parameter is set to “YES”, this unit receives the information on the available video signal resolutions from the video monitor connected via HDMI (see page 22).
01EN_YSP-4000_UA.book Page 98 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters 4 Press / to switch between “MON CHK: YES” and “MON CHK: SKIP”. ENTER Setting the DEMO MODE You can test the sound beam output from this unit to experience the sound beam. 1 Repeat steps 1 to 3 in “Using the system parameters” on page 94. 2 Set the operation mode selector to YSP. TV/AV MON CHK: YSP YES 3 MON CHK: Press / so that “DEMO MODE” is displayed in the front panel display.
01EN_YSP-4000_UA.book Page 99 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters 5 Press / to switch between “DEMO: ON” and “DEMO: OFF”. ENTER Setting the PANEL INPUT KEY You can disable the INPUT on the front panel when you adjust the system parameters. 1 Repeat steps 1 to 3 in “Using the system parameters” on page 94. 2 Set the operation mode selector to YSP. TV/AV DEMO: YSP ON 3 DEMO: Press / so that “PANEL INPUT KEY” is displayed in the front panel display.
01EN_YSP-4000_UA.book Page 100 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters 5 Press / to switch between “P.INPUT: ON” and “P.INPUT: OFF”. ENTER Disabling the front panel keys You can disable the front panel keys except when you adjust the system parameters. 1 Repeat steps 1 to 3 in “Using the system parameters” on page 94. 2 Set the operation mode selector to YSP. TV/AV P.INPUT: YSP ON 3 P.INPUT: Press / so that “F.PANEL KEY” is displayed in the front panel display.
01EN_YSP-4000_UA.book Page 101 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters 5 Press / to switch between “F.PANEL: ON” and “F.PANEL: OFF”. ENTER Setting the FACTORY PRESET You can reset all of the parameters of this unit to the factory presets. This procedure completely resets ALL the parameters in SET MENU. Note After performing the following procedure you must run AUTO SETUP again to match your surround sound environment. F.
01EN_YSP-4000_UA.book Page 102 Wednesday, December 26, 2007 3:00 PM Adjusting the system parameters 5 Press / to switch between “PRESET: RESET” and “PRESET: CANCEL”. ENTER PRESET: RESET PRESET:CANCEL • Select PRESET: RESET to reset all of the current settings. • Select PRESET: CANCEL to cancel the resetting procedure. 6 Press STANDBY/ON on the remote control to set this unit to the standby mode. STANDBY/ON The new setting will be activated when you turn on the power of this unit next time.
01EN_YSP-4000_UA.book Page 103 Wednesday, December 26, 2007 3:00 PM Remote control features Remote control features In addition to controlling this unit, the remote control can also operate other AV components made by Yamaha and other manufacturers. To control other components, you must set up the remote control with the appropriate remote control codes and set the operation mode selector to TV/AV to change the control area.
01EN_YSP-4000_UA.book Page 104 Wednesday, December 26, 2007 3:00 PM Remote control features Controlling other components ■ Operating your TV Set the operation mode selector to TV/AV, and press TV to select TV as the input source. The control area of the remote control changes to the TV operation mode.
01EN_YSP-4000_UA.book Page 105 Wednesday, December 26, 2007 3:00 PM Remote control features ■ Operating your DVD player/recorder Set the operation mode selector to TV/AV and press DVD to select DVD as the input source. The control area of the remote control changes to the DVD operation mode. TV/AV ■ Operating your STB (CATV/Satellite tuner) Set the operation mode selector to TV/AV and press STB to select STB as the input source. The control area of the remote control changes to the STB operation mode.
01EN_YSP-4000_UA.book Page 106 Wednesday, December 26, 2007 3:00 PM Remote control features ■ Operating your VCR Set the operation mode selector to TV/AV and press AUX1 to select VCR as the input source. The control area of the remote control changes to the AUX1 operation mode. y This operation is available when your VCR is connected to the AUX 1 AUDIO IN jacks on this unit.
01EN_YSP-4000_UA.book Page 107 Wednesday, December 26, 2007 3:00 PM Remote control features ■ Setting macros for the TV with the tuning capability Using the TV macro The TV macro feature makes it possible to perform a series of operations with the press of a single button. For example, when you want to play a DVD, you would normally turn on the component, select DVD as the input source, and press the play button to start playback.
01EN_YSP-4000_UA.book Page 108 Wednesday, December 26, 2007 3:00 PM Remote control features ■ Setting macros for the TV without the tuning capability 1 Press and hold CODE SET and press one of the input selector buttons to select the input source you want to set macros for. Proceed to step 2 while holding down CODE SET. TV MUTE DVD Press and hold one of the input selector buttons for approximately two seconds to select the input source you want to operate macros for.
01EN_YSP-4000_UA.book Page 109 Wednesday, December 26, 2007 3:00 PM Troubleshooting Troubleshooting Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the AC power supply cable, and contact the nearest authorized Yamaha dealer or service center.
01EN_YSP-4000_UA.book Page 110 Wednesday, December 26, 2007 3:00 PM Troubleshooting Problem No sound from the subwoofer. Cause BASS OUT in SUBWOOFER SET is set to FRONT. Remedy Select SWFR. See page 83 The source does not contain low bass signals. Distorted or too little bass sound. CROSS OVER in SUBWOOFER SET is set incorrectly. Set CROSS OVER correctly. One of the night listening enhancers is currently selected. Turn off the night listening enhancers. TruBass is currently turned on.
01EN_YSP-4000_UA.book Page 111 Wednesday, December 26, 2007 3:00 PM Troubleshooting ■ Remote control Problem The remote control does not work and/or function properly. Cause Remedy See page Wrong distance or angle. The remote control functions within a maximum range of 6 m (20 ft) and no more than 45 degrees off-axis from the front panel. 32 Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition this unit.
01EN_YSP-4000_UA.book Page 112 Wednesday, December 26, 2007 3:00 PM Troubleshooting ■ FM tuner Problem Cause FM stereo reception is noisy. The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor. Remedy See page Check the antenna connections. 30 Try using a high-quality directional FM antenna. — Use the manual tuning method. 51 There is distortion, and clear reception cannot be obtained even with a good FM antenna.
01EN_YSP-4000_UA.book Page 113 Wednesday, December 26, 2007 3:00 PM Glossary Glossary ■ Dolby Digital ■ DTS Digital Surround Dolby Digital is a digital surround sound system that gives you completely independent multi-channel audio. With 3 front channels (left, center, and right) and 2 surround stereo channels, Dolby Digital provides 5 full-range audio channels. With an additional channel especially for bass effects, called LFE (low-frequency effect), the system has a total of 5.
01EN_YSP-4000_UA.book Page 114 Wednesday, December 26, 2007 3:00 PM Glossary ■ LFE 0.1-channel This channel is for the reproduction of low bass signals. The frequency range for this channel is 20 Hz to 120 Hz. This channel is counted as 0.1 because it only enforces a low-frequency range compared to the full-range reproduction by the other 5/6 channels in Dolby Digital or DTS 5.1/6.1-channel systems.
01EN_YSP-4000_UA.book Page 115 Wednesday, December 26, 2007 3:00 PM Index Index ■ Numerics ■ M 3 Beam ............................................................................ 57 5 Beam ............................................................................ 56 MANUAL SETUP ..........................................................76 MEMORY .......................................................................44 Movie program................................................................
01EN_YSP-4000_UA.book Page 116 Wednesday, December 26, 2007 3:00 PM Specifications Specifications AMP SECTION FM SECTION • Maximum Output Power (JEITA) ................................................. 2 W (1 kHz, 10% THD, 4 Ω) × 40 20 W (100 Hz, 10% THD, 4 Ω) × 2 • Tuning Range [U.S.A., Canada, and Asia models] ................ 87.5 to 107.9 MHz [Other models] ............................................ 87.50 to 108.00 MHz SPEAKER SECTION GENERAL • Driver Small dia. speakers ......................
01EN_YSP-4000_UA.
01EN_YSP-4000_UA.
00cv_YSP-4000_UA.fm Page 1 Friday, March 7, 2008 10:23 AM UA YSP-4000 YSP-4000 Digital Sound ProjectorTM © 2007 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY YAMAHA ELECTRONIQUE FRANCE S.A.
UA YSP-4000 Digital Sound ProjectorTM Reference Guide for iPodTM/XMTM Radio Overview This is the Reference Guide for Yamaha YSP-4000 Digital Sound Projector. This guide explains the connections and operations of iPod and XM Satellite Radio (U.S.A. and Canada models only). Operations in this guide use keys on the supplied remote control unless otherwise specified. For general information including the controls and functions of this unit, refer to the owner’s manual.
USING IPOD™ Using iPod™ This unit has the DOCK terminal on the rear panel that allows you to connect the Yamaha iPod universal dock (such as YDS-10, sold separately). Station your iPod in the Yamaha iPod universal dock, and use the supplied remote control to operate your iPod. Notes • Only iPod (Click and Wheel), iPod nano, and iPod mini are supported. • Some features may not be compatible depending on the model or the software version of your iPod.
01EN_YSP-4000_UA-RG.book Page 3 Friday, March 7, 2008 11:25 AM Using iPod™ y • For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in “Troubleshooting” on page 11. • While your iPod is stationed in the Yamaha iPod universal dock connected to the DOCK terminal of this unit, your iPod battery is automatically charged as long as this unit is turned on.
01EN_YSP-4000_UA-RG.book Page 4 Wednesday, December 26, 2007 10:39 AM Using iPod™ y 4 Press / and / to navigate through the iPod menu, and press ENTER to start playback of the selected song. ENTER and ENTER • Press RETURN or MENU to go back to the previous menu. • The information on the current song also appears in the front panel display. You can set the front panel display mode: CONT. or ONCE. For details, see “SCROLL” (Front panel display scroll) in “F.
XM™ SATELLITE RADIO TUNING (U.S.A. AND CANADA MODELS ONLY) XM™ Satellite Radio tuning (U.S.A. and Canada models only) ■ About XM Satellite Radio XM Satellite Radio offers an extraordinary variety of commercial-free music, plus the best in sports, news, talk, and entertainment. XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.
XM™ Satellite Radio tuning (U.S.A. and Canada models only) Activating XM™ Satellite Radio Once you have installed XM Mini-Tuner Home Dock, inserted XM Mini-Tuner, connected Home Dock to your XM READY home audio system, and installed the antenna, you are ready to subscribe and begin receiving XM programming. There are three places to find your eight-character XM Radio ID: on XM Mini-Tuner, on XM Mini-Tuner package, and on XM Channel 0 (see “All Channel Search mode” on page 7).
XM™ Satellite Radio tuning (U.S.A. and Canada models only) ■ Category Search mode 3 Search for a desired channel by using one of the four XM Satellite Radio search modes: • To select a channel from all channels, see “All Channel Search mode” on this page. • To select a channel by channel category, see “Category Search mode” on this page. • To select a channel from the preset channels, see “Preset Search mode” on page 8.
XM™ Satellite Radio tuning (U.S.A. and Canada models only) ■ Preset Search mode Prior to selecting a preset channel in the Preset Search mode, you must preset the XM channels. For details, see “Presetting the XM™ Satellite Radio channels” on page 9. 1 ■ Direct Number Access mode 1 Press SEARCH repeatedly to select either “ALL CH SEARCH” or “CAT SEARCH”. Press SEARCH repeatedly to select “PRESET SEARCH”.
XM™ Satellite Radio tuning (U.S.A. and Canada models only) Presetting the XM™ Satellite Radio channels 4 You can use this feature to store up to 40 XM Satellite Radio channels (A1 to E8: 5 preset channel groups with 8 preset channel numbers each). You can then recall the preset channels easily by selecting the preset group and number as described in “Preset Search mode” on page 8. Press ENTRY ( / ) repeatedly to select a preset number while the MEMORY indicator is flashing.
XM™ Satellite Radio tuning (U.S.A. and Canada models only) Displaying the XM™ Satellite Radio information You can display the XM Satellite Radio information (channel number/channel name, channel category, and artist name/song or program title) for the currently selected channel in the front panel display or in the OSD. Note If a status or error message appears in the front panel display or in the OSD, see the “XM Satellite Radio (U.S.A. and Canada models only)” in “Troubleshooting” on page 11.
TROUBLESHOOTING Troubleshooting Refer to the following charts when the status messages appear during your iPod or XM Satellite Radio operations on this unit. If you experience a problem that is not listed below, or if the instruction below does not help, set this unit to the standby mode, disconnect the power supply cable, and contact the nearest authorized Yamaha dealer or service center.
01EN_YSP-4000_UA-RG.book Page 12 Friday, March 7, 2008 11:25 AM © 2007 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD.
Items used for connections and operations in this guide s Audio pin cable (x1) s OSD* video pin cable (x1) s Optical cable (x1) s Coaxial cable (x1) s AC power supply cable (x1) s IntelliBeam microphone (x1) s Cardboard microphone stand (x1) s Demonstration DVD (x1) *OSD: On-Screen Display YSP-4000 QUICK REFERENCE GUIDE This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the surround sound effects in a quick, easy manner.
Continued from the front 3 Carry out the AUTO SETUP (IntelliBeam) Carry out the AUTO SETUP to adjust the settings that best match your listening environment 6 Set the operation mode selector to YSP. This unit switches to the YSP operation mode. ENHANCER The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output during the AUTO SETUP procedure.