Quick Reference Guide

ManualsBrandsYamaha Manualsaudio & home theatreYSP-5100

1) Press HDMI1-4 or AUX1/2 to

select the Blu-ray disc player

as the input source.

For example, if the Blu-ray disc player is connected to the

HDMI IN 1 jack of this unit (as shown in “Example - A”),

press HDMI1.

HDMI 4 iPod RADIO

ENTER

HDMI 1 HDMI 2 HDMI 3

TV AUX 1 AUX 2

TV AV

2) Start playback of a Blu-ray

disc.

Select the Blu-ray disc player

as the video input on your TV.

Select the desired TV channel.

Press TV to select the TV as the

input source.

HDMI 4 iPod RADIO

ENTER

HDMI 1 HDMI 2 HDMI 3

TV AUX 1 AUX 2

TV AV

Press and hold INTELLIBEAM

for more than 2 seconds.

The INTELLIBEAM key is located inside of the slide cover.

7 8 9

4 5 6

1 2 3

UNIVOLUME SUR. DECODE INTELLIBEAM

PREPARATION & CHECK

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from the unit.

The MIC should be set

at ear level when seated.

Measurement takes about 3min.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

AUTO SETUP

Make sure that your listening

room is as quiet as possible.

For accurate measurement, turn off air conditioner or other

devices that make noises.

Prepare to leave the room.

The best setting may not be done if you are in the room.

Prepare to leave the room in 10 seconds after pressing ENTER

in step 8.

When leaving the room, bring this Quick Reference Guide with you.

Wait outside the room during the AUTO SETUP procedure.

The AUTO SETUP procedure takes about 3 minutes.

To cancel the AUTO SETUP procedure after it is started, press

RETURN.

•

Press ENTER.

The following screen appears on the TV for 2 seconds and

then the menu screen disappears from the TV.

ENTER

SURROUND

CINEMA DSP

MENUTOP MENU

STEREO

AUTO SETUP COMPLETE

Please remove the MIC from

the unit and the listening

position.

Disconnect the IntelliBeam

microphone.

Now the AUTO SETUP is complete. Keep the IntelliBeam

microphone in a safe place.

The settings are automatically saved in the system memory.

INPUT VOLUME INTELLIBEAM MIC

INTELLIBEAM MIC

Enjoying TV in surround sound

Press VOLUME +/- to adjust the volume.

If the TV speakers output sounds, mute it.

MUTE

INPUT MUTE

TV VOL CH VOLUME

Enjoying Blu-ray discs in surround sound

Carry out the AUTO SETUP to adjust the settings so that the best listening

environment is created.

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output during the

AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.

Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC

jack on the front panel.

If necessary, use the supplied cardboard microphone stand. Assemble the stand and place the IntelliBeam microphone on top of it

horizontally as shown below.

INPUT VOLUME INTELLIBEAM MIC

INTELLIBEAM MIC

1 2 3 4 5

IntelliBeam microphone (supplied)

Cardboard microphone stand (supplied)

Set the IntelliBeam microphone at your normal listening position.

Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be

when you are seated.

1.8 m (6.0 ft)

or more

Within 1 m (3.3 ft)

IntelliBeam microphone

Cardboard

microphone

stand

Listening

position

Place the IntelliBeam microphone on the

extended center line of this unit and 1.8 m

(6.0 ft) or more away from it. Also, make

sure place the IntelliBeam microphone

within 1 m (3.3 ft) upper or lower from the

center height of this unit.

IntelliBeam

microphone

Center line

Within 1 m (3.3 ft)

Cardboard microphone stand

Upper limit

Lower limit

Center height of

this unit

4 Turn on the power of your TV

and select this unit as the video

input on your TV.

If this unit is connected to the HDMI input on the TV (as

shown in “Example - A”), switch the video input to “HDMI”.

If this unit is connected to the video input 1 on the TV (as

shown in “Example - B”), switch the video input to “1”.

3 Press the Power ( ) key on the

remote control.

The power of this unit turns on.

If a subwoofer with adjustable volume and crossover

frequency controls is connected to this unit, turn it on, set

the volume to about half way and then set the crossover

frequency to the maximum as shown below.

HDMI 1 HDMI 2 HDMI 3

TV AUX 1 AUX 2

TV AV

VOLUME

MIN MAX

CROSSOVER/

HIGH CUT

MIN MAX

Subwoofer

Press SURROUND and then the CINEMA DSP keys to

select the desired CINEMA DSP program.

Each time you press the CINEMA DSP key, program switches. For details on each program, see

“Enjoying CINEMA DSP programs” of “Owner’s Manual” (on the supplied CD-ROM). To turn off the

CINEMA DSP program, press OFF.

HDMI 4 iPod RADIO

SURROUND

OFF

ENTER

TAINMENT

MUSIC

CINEMA DSP

MOVIE

HDMI 1 HDMI 2 HDMI 3

TV AUX 1 AUX 2

STEREO

TV AV

Start play back of your iPod/

iPhone.

INPUT VOLUME INTELLIBEAM MIC

For proper transmission, you need to set the group IDs of this unit

and PDX-50TX to the same value. For the Group ID setting of this

unit, refer to “WIRELESS SETUP” of “Owner’s Manual” (supplied

CD-ROM).

•

Prepare your iPod/iPhone

and the Yamaha wireless

transmitter for iPod (PDX-50TX/

PDX-50BC).

For instructions on PDX-50TX/PDX-50BC, refer to “Safety

and Accessory Information” (separate booklet).

Press RADIO repeatedly to

select “FM”.

HDMI 4 iPod RADIO

OFF

ENTER

TAINMENT

MUSIC

CINEMA DSP

MOVIE

HDMI 1 HDMI 2 HDMI 3

TV AUX 1 AUX 2

TV AV

X X X X

F M

8 8 . 9

M H z

Press TUNING / .

Frequency is changed.

4 5 6

1 2 3

UNIVOLUME SUR. DECODE INTELLIBEAM

MEMORY

SLEEPINFO

TUNING PRESET CATEGORY

X X X X

F M

9 2 . 5

M H z

FM tuningPlaying back iPod/iPhone

Using the audio functions of this unit

Adjusting volume level automatically (UNIVOLUME)

Selecting surround or stereo playback

Press SURROUND or STEREO.

You can enjoy stereoscopic sound ﬁeld with surround playback and hi-ﬁ

sound with stereo playback.

ENTER

SURROUND

CINEMA DSP

MENUTOP MENU

STEREO

Press UNIVOLUME.

You can limit the volume level of the TV so that it will not increase suddenly

when whenever the contents being broadcast change (due to commercials,

etc.). The UNIVOLUME key is located inside of the slide cover.

7 8 9

4 5 6

1 2 3

UNIVOLUME SUR. DECODE INTELLIBEAM

Basic playback operations

Press ENTER to start the AUTO

SETUP procedure and then leave

the room within 10 seconds.

ENTER

SURROUND

CINEMA DSP

MENUTOP MENU

STEREO

Will begin in 10sec

Please leave the room

*--------

[RETURN]:Cancel

AUTO SETUP START

The setup screen automatically changes during the AUTO

SETUP procedure.

When the AUTO SETUP procedure is complete, the “SHOW

RESULT” screen appears on the TV.

MEASUREMENT COMPLETE

BEAM MODE :5Beam/Plus2

SUBWOOFER :YES

[ENTER]:Save set-up.

[RETURN]:Do not save set-up.

SHOW RESULT

If “ENVIRONMENT CHECK (FAILED)” is displayed, see “Error

massages for AUTO SETUP” of “Owner’s Manual” (on the

supplied CD-ROM) and then run the procedure again.

The result may differ depending on the environment.

If any error occurs, the corresponding error message appears on the

screen. In this case, see “Error massages for AUTO SETUP” of “Owner’

s Manual” (on the supplied CD-ROM).

•

Checking digital

audio input

You can check the digital signals being input from the Blu-ray disc player through

the digital connection (HDMI, optical, coaxial) by using the supplied demonstration

DVD.

Press HDMI1-4 or AUX1/2 to

select the Blu-ray disc player

as the input source and start

playback of the demonstration

DVD.

HDMI 4 iPod RADIO

ENTER

HDMI 1 HDMI 2 HDMI 3

TV AUX 1 AUX 2

Check whether the

DIGITAL

indicator lights up.

DIGITAL

If the indicator does not light up, check the setting for digital audio output

on the player. For details, see “Using the supplied demonstration DVD”

(page 7 of “Safety and Accessory Information” (separate booklet)).

•

Playing back audio signals

Carrying out the AUTO SETUP (IntelliBeam)

Playing back audio signals

– 5 –