UB YST-SW005 Subwoofer System OWNER’S MANUAL I
IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. CAUTION 2 Keep these instructions. RISK OF ELECTRIC SHOCK DO NOT OPEN 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See the user manual instructions if interference to radio reception is suspected. FCC INFORMATION (for US customers only) 1. 2. 3.
UNPACKING After unpacking, check that the following item is contained.
English Thank you for selecting this YAMAHA subwoofer system. CAUTION: Read this before operating your unit. ● To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. ● If you hear distorted noise (i.e., unnatural, intermittent “rapping” or “hammering” sounds) coming from this unit, reduce the volume level.
FEATURES ● This subwoofer system employs Advanced YAMAHA Active Servo Technology which YAMAHA has developed for reproducing higher quality super-bass sound. (Refer to page 12 for details on Advanced YAMAHA Active Servo Technology.) This super-bass sound adds a more realistic, theater-in-the-home effect to your stereo system. ● This subwoofer can be easily added to your existing audio system by connecting to either the speaker terminals or the line output (pin jack) terminals of the amplifier.
Å ( ı : subwoofer, Ç English PLACEMENT : main speaker) One subwoofer will have a good effect on your audio system, however, the use of two subwoofers is recommended to obtain more effect. If using one subwoofer, it is recommended to place it on the outside of either the right or the left main speaker. (See fig. Å.) If using two subwoofers, it is recommended to place them on the outside of each main speaker. (See fig. ı.) The placement shown in fig.
CONNECTIONS Caution: Plug in the subwoofer and other components after all connections are completed. ● All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s manual for each of your components. ● Basically, connect the subwoofer to the line output (pin jack) terminal(s) of the amplifier. (Refer to pages 4 and 5 for details.
English 䡵 Using two subwoofers Left main speaker Right main speaker INPUT2 INPUT2 /MONO Right subwoofer /MONO Left subwoofer VOLUME VOLUME 0 0 AUTO STANDBY AUTO STANDBY HIGH CUT HIGH HIGH CUT LOW HIGH LOW OFF LOW INPUT2 INPUT2 10 10 HIGH HIGH LOW OFF /MONO /MONO INPUT1 FROM AMPLIFIER INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS OUTPUT TO SPEAKERS SPLIT SUBWOOFER POWER POWER ON ON OFF OFF Amplifier To AC outlet To AC outlet Notes ● If your amplifier has two sets of PRE OUT termi
Connecting to speaker output terminals of the amplifier 䡵 Using one subwoofer If your amplifier has only one set of main speaker output terminals Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers.
English 䡵 Using two subwoofers Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers.
CONTROLS AND THEIR FUNCTIONS Front panel SUBWOOFER SYSTEM YST-SW005 YST SW005 1 Port Rear panel VOLUME 8 VOLUME 0 AUTO STANDBY POWER 2 10 HIGH 0 ON INPUT2 OFF 10 HIGH CUT LOW HIGH LOW OFF /MONO AUTO STANDBY 4 HIGH LOW OFF HIGH HIGH CUT LOW 9 INPUT1 FROM AMPLIFIER 5 OUTPUT TO SPEAKERS 3 220V-240V POWER 110V-120V 2 3 E-8 6 INPUT1 FROM AMPLIFIER VOLTAGE SELECTOR 220V-240V 1 /MONO ON OFF 110V-120V INPUT2 VOLTAGE SELECTOR Power indicator Lights up GREEN when the POWE
If the source being played is stopped and the input signal is cut off for 7 to 8 minutes, the subwoofer automatically switches to the standby mode. (When the subwoofer switches to the standby mode by the automatic powerswitching function, the power indicator lights up in red.) When you play a source again, the power of the subwoofer turns on automatically by sensing audio signals input to the subwoofer. This function will operate by sensing a certain level of low frequency input signal.
ADJUSTING THE SUBWOOFER BEFORE USE Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and the main speakers by following the procedures described below.
English 䡵 Frequency characteristics 100 Fig. 1 shows the frequency characteristics of the subwoofer with each position (HIGH/LOW) of the HIGH CUT switch. HIGH CUT HIGH 90 80 70 HIGH CUT LOW 60 50 40 20 50 100 200 500Hz Fig. 1 Fig. 2 shows the optimum volume level with the HIGH CUT switch at the HIGH position, and the frequency characteristics when the subwoofer is combined with a typical 3.5” or 4” (8 cm or 10 cm) acoustic suspension, 2 way system main speakers.
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY The theory of Yamaha Active Servo Technology has been based upon two major factors, the Helmholtz resonator and negative-impedance drive. Active Servo Processing speakers reproduce the bass frequencies through an “air woofer”, which is a port or opening in the speaker’s cabinet. This opening is used instead of, and performs the functions of, a woofer in a conventionally designed speaker system.
English TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center. Problem Cause What to Do Power is not supplied even though the POWER switch is set to the ON position. The power plug is not securely connected. Connect it securely. No sound. The VOLUME control is set to 0.
SPECIFICATIONS Type .............. Advanced Yamaha Active Servo Technology Driver ....................................... 16 cm (6-1/2”) cone woofer Magnetic shielding type Amplifier Output USA and Canada models .................................. 55 W/5Ω Other models ..................................................... 50 W/5Ω Frequency Response .............................. 30 Hz to 200 Hz Power Supply USA and Canada models ....................... AC 120V, 60 Hz U.K. and Europe models ...................
YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.