UB YST-SW105 Active Servo Processing Subwoofer System OWNER’S MANUAL I
• Explanation of Graphical Symbols CAUTION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
FCC INFORMATION (for US customers only) 1. 2. 3. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used.
UNPACKING After unpacking, check that the following item is contained.
Thank you for selecting this YAMAHA Subwoofer System. CAUTION: Read this before operating your unit. ● To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. ● Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose this unit to rain or water. ● Never open the cabinet.
CONTENTS SAFTY INSTRUCTOINS .......................... II CONTROLS AND THEIR FUNCTIONS ... 8 UNPACKING ........................................... IV AUTOMATIC POWER-SWITCHING FUNCTION ............................................... 9 CAUTION .................................................. 1 FEATURES ............................................... 2 ADJUSTING THE SUBWOOFER BEFORE USE ........................................ 10 PLACEMENT ............................................
PLACEMENT Å ( ı : subwoofer, Ç : main speaker) One subwoofer will have a good effect on your audio system, however, the use of two subwoofers is recommended to obtain more effect. If using one subwoofer, it is recommended to place it on the outside of either the right or the left main speaker. (See fig. Å.) If using two subwoofers, it is recommended to place them on the outside of each main speaker. (See fig. ı.) The placement shown in fig.
CONNECTIONS Caution: Plug in the subwoofer and other audio/video components after all connections are completed. • All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s manual for each of your components. • Basically, connect the subwoofer to the line output (pin jack) terminal(s) of the amplifier. (Refer to pages 4 and 5 for details.
■ Using two subwoofers Right main speaker Left main speaker OUTPUT TO SPEAKERS + – – + – – + INPUT 2 OUTPUT + TO SPEAKERS – – + – – + /MONO + OUTPUT + TO SPEAKERS – – + – – + /MONO + FROM AMPLIFIER FROM AMPLIFIER INPUT 1 INPUT 1 Subwoofer Subwoofer INPUT 2 AUTO STANDBY OUTPUT + TO SPEAKERS – – + – – + /MONO + INPUT 2 INPUT 2 AUTO STANDBY /MONO + OFF LOW HIGH OFF FROM AMPLIFIER LOW HIGH FROM AMPLIFIER INPUT 1 INPUT 1 POWER POWER ON ON OFF O
Connecting to speaker output terminals of the amplifier ■ Using one subwoofer If your amplifier has only one set of main speaker output terminals Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers.
■ Using two subwoofers Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers.
CONTROLS AND THEIR FUNCTIONS Front panel SUPERWOOFER SYSTEM YST-SW105 STANDBY/ ON B.A.S.S. HIGH CUT 50Hz STANDBY/ ON B.A.S.S.
¤ # ‹ $ OUTPUT (TO SPEAKERS) terminals Can be used for connecting to the main speakers. Signals from the INPUT1 terminals ($) are sent to these terminals. (Refer to “CONNECTIONS” for details.) INPUT2 terminals Used to input line level signals from the amplifier. (Refer to “CONNECTIONS” for details.) AUTO STANDBY (HIGH/LOW/OFF) switch This switch is originally set to the OFF position.
ADJUSTING THE SUBWOOFER BEFORE USE Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and the main speakers by following the procedures described below. Front panel SUPERWOOFER SYSTEM YST-SW105 STANDBY/ ON B.A.S.S. HIGH CUT VOLUME MOVIE MUSIC 50Hz 150Hz 0 STANDBY/ ON 10 B.A.S.S. HIGH CUT 50Hz 3 1 2 3 Set the VOLUME control to minimum (0). Turn on the power of all the other components.
Frequency characteristics This subwoofer’s frequency characteristics dB HIGH CUT 100 Hz 90 HIGH CUT 150 Hz 80 70 HIGH CUT 50 Hz 60 50 40 20 50 100 200 500Hz The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer is combined with a typical main speaker system. EX.
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY The theory of Yamaha Active Servo Technology has been based upon two major factors, the Helmholtz resonator and negative-impedance drive. Active Servo Processing speakers reproduce the bass frequencies through an “air woofer”, which is a port or opening in the speaker’s cabinet. This opening is used instead of, and performs the functions of, a woofer in a conventionally designed speaker system.
TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cable and contact your authorized YAMAHA dealer or service center. Problem Cause What to Do Power is not supplied even though the STANDBY/ON button is set to the ON position. The power cable is not plugged in, or the POWER switch is set to the OFF position.
SPECIFICATIONS Type ............... Advanced Yamaha Active Servo Technology Power Consumption ................................................... 80W (In the standby mode: 0.8W) Driver ............................................. 20 cm (8”) cone woofer, Magnetic shielding type Dimensions (W x H x D) ...... 235 mm x 365 mm x 312 mm (9-5/16” x 14-7/20” x 12-5/16”) Amplifier Output .................................................. 100W/5Ω Weight .............................................. 9.
YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA 16 ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD.