UB YST-SW1500 Subwoofer System OWNER’S MANUAL 1-YST-SW1500(UB)PRE-f 1 02.9.
IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
FCC INFORMATION (for US customers) 1. 2. 3. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used.
CHECKING THE ACCESSORIES Check your package to make sure it contains the following items. ● Remote control ● Batteries (size AA, UM-3, R6) ● Grounding cable ● Power cable (U.S.A., Canada, Europe and Korean models only) (U.S.A. and Canada models) (Europe and Korean models) SPECIAL INSTRUCTIONS FOR U.K. MODEL For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted.
English Thank you for selecting this YAMAHA Subwoofer System. CAUTION: Read this before operating your unit. Please read the following operating precautions before use. YAMAHA will not be held responsible for any damage and/or injury caused by not following the cautions below. ● ● ● ● ● ● ● ● ● ● ● ● ● ● To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
CONTENTS IMPORTANT SAFETY INSTRUCTIONS ................................................................. II NOTES ABOUT THE REMOTE CONTROL ............................................. 11 CHECKING THE ACCESSORIES .......... IV CONTROLS AND THEIR FUNCTIONS .......................................... 12 CAUTION .................................................. 1 FEATURES ............................................... 2 PLACEMENT ............................................ 3 CONNECTIONS .................
PLACEMENT Å ( ı : subwoofer, Ç : main speaker) One subwoofer will have a good effect on your audio system, however, the use of two subwoofers is recommended to obtain more effect. If using one subwoofer, it is recommended to place it on the outside of either the right or the left main speaker. (See fig. Å.) If using two subwoofers, it is recommended to place them on the outside of each main speaker. (See fig. ı.) The placement shown in fig.
CONNECTIONS Caution: Plug in the subwoofer and other audio/video components after all connections are completed. ● All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s manual for each of your components. ● The subwoofer can be connected to either the line output (pin jack) terminals or the speaker output terminals of the amplifier. Choose one of the ways shown in this section that is more suitable for your audio system.
English 䡵 Using two subwoofers Right main speaker Left main speaker LFE OUTPUT H.P.F.OUTPUT NORMAL TO SPEAKERS /MONO 80Hz 100Hz NORMAL /MONO OUTPUT TO SPEAKERS Mono pin cables (not included) LFE H.P.F.OUTPUT 80Hz 100Hz GND INPUT 3 INPUT 2 GND Right subwoofer REMOTE OUTPUT INPUT AUTO STANDBY HIGH LOW OFF H.P.F.
Connecting to speaker output terminals of the amplifier 䡵 Using one subwoofer If your amplifier has only one set of main speaker output terminals Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers. Right main speaker Left main speaker LFE H.P.F.OUTPUT OUTPUT NORMAL TO SPEAKERS /MONO 80Hz 100Hz GND Subwoofer REMOTE OUTPUT INPUT AUTO STANDBY HIGH LOW OFF H.P.F.
English 䡵 Using two subwoofers Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers. Right main speaker LFE H.P.F.OUTPUT Left main speaker NORMAL /MONO 80Hz 100Hz GND REMOTE AUTO STANDBY HIGH LOW OFF H.P.F.
Connecting to H.P.F. OUTPUT terminals The use of the H.P.F. OUTPUT terminals for connections with the amplifier will improve sound quality of your speaker system. The H.P.F. (High-Pass Filter) OUTPUT terminals of the subwoofer cut off frequencies below the selected frequency point from the input signals, and output high frequencies only. By connecting this terminal with the MAIN IN terminals of the amplifier, the main speakers reproduce high frequencies only.
English 䡵 To connect two units Right main speaker Left main speaker LFE H.P.F.OUTPUT OUTPUT NORMAL H.P.F.OUTPUT TO SPEAKERS /MONO AUTO STANDBY LOW OFF H.P.F.OUTPUT LFE NORMAL INPUT 3 INPUT 2 /MONO INPUT 2 GND INPUT 2 FROM AMPLIFIER FROM AMPLIFIER INPUT 1 INPUT 1 Left subwoofer OUTPUT REMOTE TO SPEAKERS 80Hz 100Hz OUTPUT INPUT GND INPUT 3 AUTO STANDBY HIGH LOW OFF H.P.F.
Ground connection If there is a humming noise when using the subwoofer connected to the speaker terminals, connect the subwoofer and the receiver/amplifier with the grounding cable as shown in Illustration A. * If there is no ground terminal (GND) on the receiver/amplifier side, connect the cable to a screw that fastens the top cover of the receiver/amplifier to the rear panel as shown in Illustration B. Insert Tighten Grounding cable Subwoofer AUTO STANDBY REMOTE OUTPUT INPUT HIGH LOW LFE H.P.F.
English Connecting the AC power cable POWER ON OFF AC IN When all connections are completed, plug the included power cable into the AC IN socket of the subwoofer, and then plug in the power cable to the wall outlet. (U.S.A. model) To AC outlet Notes ● Never connect any power cable other than the included one to the subwoofer. Otherwise, it may result in causing fire or an electrical shock.
CONTROLS AND THEIR FUNCTIONS Front panel 5 6 78 9 SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE STANDBY/ON PHASE B.A.S.S. PRESET 2 1 HIGH CUT 40Hz 14Hz 3 VOLUME 0 10 SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE STANDBY/ON B.A.S.S. PHASE 40Hz 1 2 PRESET 2 1 HIGH CUT 3 VOLUME 140Hz 3 0 10 4 Rear panel REMOTE OUTPUT INPUT AUTO STANDBY HIGH LOW OFF H.P.F.
5 6 7 8 9 0 A B VOLUME control VOLUME UP/DOWN buttons Adjust the volume level. Turn the control clockwise or press the UP button to increase the volume. Turn the control counterclockwise or press the DOWN button to decrease the volume. To adjust the control on the front panel, put a coin, etc. in the groove on the control and turn it. C D Remote control sensor Receives signals from the remote control. Power indicator (LED) Lights up in green while the subwoofer is turned on.
AUTOMATIC POWER-SWITCHING FUNCTION If the source being played is stopped and the input signal is cut off for 7 to 8 minutes, the subwoofer automatically switches to the standby mode. (When the subwoofer switches to the standby mode by the automatic powerswitching function, the power indicator lights up in red.) When you play a source again, the power of the subwoofer turns on automatically by sensing audio signals input to the subwoofer.
Before using the subwoofer, adjust the subwoofer to obtain the optimum volume and tone balance between the subwoofer and the main speakers by following the procedures described below. 3 8 7 SUBWOOFER SYSTEM YST-SW1500 SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE STANDBY/ON B.A.S.S. PHASE 1 PRESET 2 HIGH CUT 40Hz 14Hz 3 VOLUME 0 MUSIC/MOVIE 10 STANDBY/ON B.A.S.S. PHASE 3 3 Set the volume level on the amplifier to minimum, and turn on the amplifier and other components.
Storing preset data of the VOLUME control etc. You can store preset data of the VOLUME control, the HIGH CUT control, the PHASE button and the B.A.S.S. switch as a set. Each of the three PRESET buttons on the remote control is used to store (and recall) one set of data. With this function, you can recall any preset data easily according to the source. 3 SUBWOOFER SYSTEM YST-SW1500 SUBWOOFER SYSTEM YST-SW1500 MUSIC/MOVIE STANDBY/ON PHASE B.A.S.S.
English Frequency characteristics This subwoofer’s frequency characteristics 100 dB HIGH CUT 40 Hz HIGH CUT 90 Hz 90 HIGH CUT 140 Hz 80 70 60 50 40 20 50 100 200 500 Hz The figures below show the optimum adjustment of each control and the frequency characteristics when this subwoofer is combined with a typical main speaker system. EX.
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY The theory of Yamaha Active Servo Technology has been based upon two major factors, the Helmholtz resonator and negative-impedance drive. Active Servo Processing speakers reproduce the bass frequencies through an “air woofer”, which is a port or opening in the speaker’s cabinet. This opening is used instead of, and performs the functions of, a woofer in a conventionally designed speaker system.
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the power cable and contact your authorized YAMAHA dealer or service center. Cause Problem What to Do Power is not supplied even though the STANDBY/ON button is set to the ON position. The power cable is not plugged in, or the POWER switch is set to the OFF position.
SPECIFICATIONS Type ............... Advanced Yamaha Active Servo Technology Power Consumption ................................................. 250W Driver ............................................ 30 cm (12”) cone woofer Standby Power Consumption ................................... 1.0W Magnetic shielding type Dimensions (W x H x D) ....... 420 mm x 511 mm x 448 mm Amplifier Output ................................................... 1 kW/5Ω (16-9/16” x 20-1/8” x 17-5/8”) Frequency Response .......