Operation Manual
Table Of Contents
- INTRODUCTION
- IMPORTANT MANUAL INFORMATION
- TABLE OF CONTENTS
- SAFETY INFORMATION
- DESCRIPTION
- INSTRUMENT AND CONTROL FUNCTIONS
- D-mode (drive mode)
- Immobilizer system
- Main switch/steering lock
- Indicator lights and warning lights
- Multi-function meter unit
- Handlebar switches
- Clutch lever
- Shift pedal
- Brake lever
- Brake pedal
- Traction control system
- Fuel tank cap
- Fuel
- Fuel tank breather hose and overflow hose
- Catalytic converter
- Seats
- Helmet holder
- Storage compartment
- Rider footrest position
- Rear view mirrors
- Adjusting the front fork
- Adjusting the shock absorber assembly
- Luggage strap holders
- Sidestand
- Ignition circuit cut-off system
- FOR YOUR SAFETY – PRE-OPERATION CHECKS
- OPERATION AND IMPORTANT RIDING POINTS
- PERIODIC MAINTENANCE AND ADJUSTMENT
- Owner’s tool kit
- Periodic maintenance chart for the emission control system
- General maintenance and lubrication chart
- Removing and installing cowlings
- Checking the spark plugs
- Engine oil and oil filter cartridge
- Coolant
- Air filter element
- Checking the engine idling speed
- Checking the throttle grip free play
- Valve clearance
- Tires
- Cast wheels
- Adjusting the clutch lever free play
- Checking the brake lever free play
- Brake light switches
- Checking the front and rear brake pads
- Checking the brake fluid level
- Changing the brake fluid
- Drive chain slack
- Cleaning and lubricating the drive chain
- Checking and lubricating the cables
- Checking and lubricating the throttle grip and cable
- Checking and lubricating the brake and shift pedals
- Checking and lubricating the brake and clutch levers
- Checking and lubricating the sidestand
- Lubricating the swingarm pivots
- Checking the front fork
- Checking the steering
- Checking the wheel bearings
- Battery
- Replacing the fuses
- Replacing a headlight bulb
- Tail/brake light
- Replacing a turn signal light bulb
- Replacing the license plate light bulb
- Auxiliary light
- Supporting the motorcycle
- Troubleshooting
- Troubleshooting charts
- MOTORCYCLE CARE AND STORAGE
- SPECIFICATIONS
- CONSUMER INFORMATION
INSTRUMENT AND CONTROL FUNCTIONS
3-35
3
EAU15305
Sidestand
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.
TIP
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See the following section for an expla-
nation of the ignition circuit cut-off sys-
tem.)
WARNING
EWA10241
The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly and have a
Yamaha dealer repair it if it does not
function properly.
EAU44892
Ignition circuit cut-off system
The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.
● It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.
● It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.
● It cuts the running engine when the
transmission is in gear and the
sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.
U1KBE1E0.book Page 35 Monday, July 9, 2012 1:05 PM