Service manual
Table Of Contents
- Cover
- History of Revision
- FOREWORD
- CONTENTS
- FOR SAFETY
- 1. General
- 2. Inspection and adjustment
- 2.1 Periodic maintenance schedule
- 2.2 Periodic inspection and maintenance procedure
- 2.2.1 Check before starting
- 2.2.2 inspection after initial 50 hours or one month operation
- 2.2.3 Inspection every 50 hours or monthly
- 2.2.4 Inspection every 100 hours six months
- 2.2.5 Inspection every 150 hours or one year
- 2.2.6 Inspection every 250 hours or one year
- 2.2.7 Inspection every 1,000 hours or four years
- 2.3 Adjusting the no-load maximum or minimum speed
- 2.4 Sensor Inspection
- 2.5 Thermostat inspection
- 2.6 Adjusting operation
- 2.7 Long storage
- 3. Troubleshooting
- 4. Disassembly and reassembly
- 5. Inspection and servicing of basic engine parts
- 6. Fuel injection equipment
- 6.1 Fuel Injection pump/governor
- 6.1.1 Fuel system diagram
- 6.1.2 Fuel injection pump service data and adjustment
- 6.1.3 Fuel injection pump structure
- 6.1.4 Removing a fuel injection pump
- 6.1.5 Installing a fuel injection pump
- 6.1.6 Adjusting fuel injection timing
- 6.1.7 Troubleshooting of fuel injection pump
- 6.1.8 Major faults and troubleshooting
- 6.2 Fuel feed pump
- 6.3 Fuel filter
- 6.4 Fuel tank
- 6.1 Fuel Injection pump/governor
- 7. Intake and exhaust system
- 8. Lubrication system
- 9. Cooling water system
- 9.1 Cooling water system
- 9.2 Seawater pump
- 9.3 Fresh water pump
- 9.4 Heat exchanger
- 9.5 Pressure cap and coolant recovery tank
- 9.5.1 Pressure cap construction
- 9.5.2 Pressure cap pressure control
- 9.5.3 Pressure cap inspection
- 9.5.4 Replacing filler neck
- 9.5.5 Function of the coolant recovery tank
- 9.5.6 Specifications of coolant recovery tank
- 9.5.7 Mounting the coolant recovery tank
- 9.5.8 Precautions on usage of the coolant recovery tank
- 9.6 Thermostat
- 9.7 Bilge pump and bilge strainer (Optional)
- 10. Reduction and reversing gear
- 11. Remote control (Optional)
- 12. Electrical system
- 13. Service standards
- 14. Tightening torque for bolts and nuts
- Colophon
- Back cover
4. Disassembly and reassembly
102
(34) Mounting the fuel filter and fuel pipe
1) Mount the fuel filter on the bracket, which is tightened to the cylinder head.
2) Mount the fuel pipe (fuel feed pump-fuel filter, fuel filter-fuel injection pump).
(35) Electrical Wiring
Connect the wiring to the proper terminals, observing the color coding to make sure the connections are
correct.
(36) Installation in a boat and completion of the piping and wiring
Mount the engine on the engine bed in the engine room of a boat after all engine assembly has been
completed. Connect the cooling water pipes, fuel pipes, other pipes on the boat and the exhaust hoses.
Connect the battery, instrument panel, remote control cable and other wiring.
(37) Filling with lube oil
Fill the engine with lube oil from the filler port on top of the gear case or the rocker arm cover. Fill the
marine gearbox from the filler port on top of the clutch case.
Cylinder head
Bracket
Fuel filter
Fuel pipe
Fuel injection pump
Clamp
Fuel pipe