Operating Guide

ManualsBrandsYard Force ManualsElectric Pressure WashersYF1600A1

Model/Modelo: YF1600A1

OPERATOR’S MANUAL

Electric Pressure Wahser

English page 1

Version 1

QUESTIONS?

SAVE THIS MANUAL

FOR REFERENCE

GUARDE ESTE MANUAL

DE REFERENCIA

¿PREGUNTAS?

Our Customer Service staff is ready

to provide assistance. In the case

of a damaged or missing part, most

replacement parts ship from our facility.

For immediate help with assembly, or for

additional product information,

visit

www.YardForceUSA.com or

email support@ForceToolsUSA.com

Nuestro personal de servicio al cliente está

listo para proveer asistencia. En el caso

de una parte dañada o faltante, la mayoría

de las piezas de repuesto se envían desde

nuestro centro.

Si necesita ayuda inmediata con el montaje,

o para obtener información adicional sobre

el producto, visite

www.YardForceUSA.

com support@ ForceToolsUSA.com

correo electrónico

You will need this manual for safety

instructions, operating procedures, and

Warranty. The original sales invoice is

required for warranty service.

Usted necesitará este manual para

las instrucciones de seguridad, los

procedimientos operativos y de Garantía.

La factura de compra original se requiere

para el servicio de garantía.

Summary of content (21 pages)

PAGE 1
Model/Modelo: YF1600A1 OPERATOR’S MANUAL Electric Pressure Wahser English page 1 Version 1 QUESTIONS? Our Customer Service staff is ready to provide assistance. In the case of a damaged or missing part, most replacement parts ship from our facility. For immediate help with assembly, or for additional product information, visit www.YardForceUSA.com or email support@ForceToolsUSA.com SAVE THIS MANUAL FOR REFERENCE You will need this manual for safety instructions, operating procedures, and Warranty.
PAGE 2
YF1600A1 Operator’s Manual TABLE OF CONTENTS Important safety instructions ..........................................................................................2 Safety features ...............................................................................................................5 Parts and diagram list ....................................................................................................6 Technical data ...........................................................................
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS Please read all of the safety precautions before operating this machine every time. Please pay particular attention to all sections with following symbols. WARNING Could cause injury or death if not followed. CAUTION Could damage machine if not followed. WARNING When using this product, basic precautions should always be followed, including: 1. 2. 3. Read all instructions before using the product. To reduce the risk of injury, do not operate the machine near children.
PAGE 4
• Do not use acids, alkaline, solvents or any flammable material in this product. These products can cause physical injuries to the operator and irreversible damage to the machine. WARNING Risk of Electric Shock. • Inspect cord before using - do not use if cord is damaged. • Keep all connections dry and off the ground. • Do not touch plug with wet hands. CAUTION Gun Kick Back. • Hold with both hands. • The trigger gun safety lock prevents the trigger from being engaged accidentally.
PAGE 5
15. Do not spray electrical apparatus and wiring or the machine itself. 16. Do not operate the pressure washer with the inlet water filter screen removed. Keep filter clear of debris and sediment. 17. Discharge residual pressure by depressing the trigger until no more water comes out of the nozzle. 18. Keep clear of nozzle. Never direct high pressure spray at any person, animal or self. 19.
PAGE 6
SAFETY FEATURES TOTAL STOP SYSTEM (TSS) The pressure washer is equipped with a total stop system (TSS) that will sense when the trigger on the gun is depressed or released. It will open the power circuit to the motor, and cause the pressure washer motor to stop. The motor will start again when the trigger is depressed. WARNING The pressure washer is also equipped with a main power “ON/OFF” (I/O) switch located on the unit.
PAGE 7
PARTS AND DIAGRAM LIST PARTS AND DIAGRAM LIST Fig. 1 Check contents of the box As shown in Fig. 1 Carefully remove the pressure washer and parts from its packaging. Identify all the parts packaged in the carton against the parts list. Please contact our customer service center (Monday - Friday 8:30AM - 5:00PM ET) at (866) 902-9690 if anything is missing.
PAGE 8
TECHNICAL DATA Model YF1600A1 Input voltage rating 120 V , 60 Hz Rated Power 13 A Working pressure 1600 PSI Max pressure 1750 PSI Rated Flow rate 1.20 GPM (275 LPH) Max. Flow rate 1.35 GPM (306 LPH) Inlet pressure 40~80 PSI Supply water temperature (max.) Cold tap water 104 °F (40 °C) Electrical cord 35 ft. (10.7 m) High-pressure hose 20 ft. (6.
PAGE 9
ASSEMBLY AND OPERATION INSTRUCTIONS Surface Preparation Before starting any cleaning task, it is important to inspect the area for objects that could create a hazard. Remove any objects from the work area that could be tripped over, such as toys or outdoor furniture. Ensure that all doors and windows are closed tightly. Water Supply (Cold Water Only) Only draw water through the unit. For use with cold water supply only. Garden hose must be at least a 1/2” (13 mm) in diameter.
PAGE 10
Fig. 4 Fig. 5 Green 25° Used for general clean Black Low pressure Used for detergent Turbo Rotating flush 3. Connect high-pressure hose to spray gun (Fig. 4) Attach high-pressure hose to the spray gun, tighten by hand until two parts are locked. 4. Fit the spray wand to spray gun (Fig. 5) Attach desired color coded spray tip to quick-connect spray wand by pushing to ensure it is clicked in securely. Insert quick–connect spray wand into the spray gun, hand tighten until two parts are locked.
PAGE 11
25° Used for general clean Low pressure Used for detergent Rotating flush This pressure washer is not intended to pump hot water. Never connect it to a hot water supply as it will significantly reduce the life of the pump. Fig. 8 Fig. 9 7. OFF position (Fig. 8) Make sure the ON/OFF switch is on the OFF position before plugging in the unit, press the switch button with mark “O” to ensure it is off. 8. Take out power cord (Fig. 9) Open the side storehousing and take out power cord with GFCI. Fig.10 9.
PAGE 12
OPERATION INSTRUCTIONS WARNING Risk of injury, Do Not Direct discharge stream at self or other persons. WARNING Before cleaning any surface, an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results. Fig.11 Turn ON the pressure washer by pressing the button with mark “ I ”. The unit will run for a few seconds to build up pressure, then will stop on the function of total stop system (TSS)(Fig.11). Fig.
PAGE 13
The pressure of spray on the surface will increase when you move the wand closer to the surface. Fig.13 OFF Turn off the pressure washer by pressing the switch button with mark “ O ”, activate the safety latch for a break. For storage, drain machine after use by removing water connection, turning ON the machine for a few seconds and depressing gun trigger to release remaining water in the pump. Turn OFF immediately (Fig. 13).
PAGE 14
2. 3. 4. 5. 6. Attach the low-pressure spray tip (black) for soap or detergent application. Detergent application will only work with low pressure spray tip. Remove the cap of detergent tank, fill tank with detergent or soap and replace the cap. Apply detergent as instructed by the detergent manufacturer (Fig. 15). Turn on the pressure washer. Squeeze trigger to operate unit. The liquid detergent will automatically mix with water, and be discharged through the nozzle.
PAGE 15
SHUTTING DOWN AND STORAGE 1. 2. 3. 4. 5. 6. 7. (If you are not using detergent, go directly to Step 2.) When you have finished using the detergent dispensing system, fill detergent tank with clean water to rinse the system clean. Squezze the gun trigger for one minute at low pressure so that all detergent remaining in system are thoroughly flushed out. Empty the remaining water, and rinse it until it is thoroughly cleaned.
PAGE 16
CLEANING AND MAINTENANCE Water Filter Screen The pressure washer is equipped with a water inlet filter screen to protect the pump. If the screen is not kept clean, the flow of water to the pressure washer will be restricted and the pump may be damaged (Fig. 17). Fig.17 1. To clean inner water screen, remove the inlet adaptor and remove the filter screen from the pump inlet. 2. Rinse screen until it is free of debris and blockage. 3.
PAGE 17
TROUBLESHOOTING Disconnect the machine from the power source before making any repairs. Symptom Motor does not run when “ON” ( I ), fully connected and trigger depressed. Unit does not reach high pressure. Cause Solution On/Off switch is in the “OFF” Turn switch to the “ON” ( I (O) position. ) position. Power cord is not plugged in. Plug in power cord. Extension cord is too long. Extension cord is not proper gauge. Extension cord is damaged. Replace extension cord with either a 25’ (7.
PAGE 18
Output pressure varies hOn/ Off switch is in the “OFF” (O) Not enough inlet water supply. position.igh and low. Detergent is not working. Turn water on fully. Check garden hose for kinks, leaks or blockage. Pump is sucking air. Check that hoses and fittings are airtight. Turn OFF machine, and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle Water inlet filter is clogged. Remove filter and rinse with warm water. Discharge nozzle is obstructed.
PAGE 19
Pump is noisy. Pump is sucking air. Check that hoses and fittings are airtight. Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle. Water filter is clogged. Remove water filter and rinse in warm water. Water leaks from pump (up Loose fittings. to 10 drops per minute is Water seals are damaged permissible). or worn. Oil is dripping. Motor buzzes but fails to run. Motor buzzes but fails to run. (continued) No water.
PAGE 20
WARRANTY Product Warranty Please keep your original purchase receipt in a safe place as proof of purchase. Warranty coverage for this product must be verified by the original purchase receipt. The warranty period begins on the day that the product was purchased from an authorized retailer of Yard Force products. Warranty coverage only applies to the original purchaser and is not transferrable. Warranty coverage is only provided on products purchased from authorized Yard Force retailers.
PAGE 21
3. If service or a warranty evaluation is requested, Yard Force will provide an RGA number that should be used in all communications with Yard Force and is required to be indicated on the product itself and on the outside of the box. 4. All shipments to Yard Force must have an RGA number. Any shipment received that does not have an RGA number clearly marked on the outside of the box will be refused. 5.