Model YF2200BL OPERATOR'S Manual Electric HIGH-PRESSURE Washer Before operating this product, please read this manual thoroughly and retain it for future reference.
DO NOT RETURN PRODUCT TO PLACE OF PURCHASE. IF YOU HAVE ANY QUESTIONS, CALL OUR TOLL-FREE HOTLINE. (866) 902-9690 ForceToolsUSA.
YF2200BL Operator's Manual TABLE OF CONTENTS Description of Product Parts………………………………………………………………………………......02 Technical Specifications…………………………………………………………………………………….....04 Intended Use……………………………………..…………………………………………………………......04 Important Safety Instructions……………………………………………………………………………….....05 Installation Instructions………………………………………………………………………………………...10 Operating Instructions……………………………………………………………………………………….....15 Cleaning and Maintenance………………………………………………………………………………….....
DESCRIPTION OF PRODUCT PARTS Parts list As shown in Fig. 1-3 1. Gun / power cord / hose holder 2. Handle with soft grip 3. Spray tips storage slots 4. Pressure adjusting knob 5. Support 6. High-pressure water outlet 7. Water inlet 8. Locking/releasing pin (not visible in this illustration) 9. On / Off Switch 10. Wheel 11. Plug 12. Power cord with GFCI 13. Attachments storage 14. Detergent intake hose 15. Nozzle cleaning needle 16. High-pressure hose 17. Quick-connect wand 18.
Check the delivery parts As shown in Fig. 4 Carefully remove the pressure washer and parts from its packaging. Identify all the parts packaged in the carton against the parts list. Please contact our customer service center (Monday-Friday 8:30AM5:00PM ET) at (866) 902 9690 if anything is missing.
TECHNICAL SPECIFICATIONS Model YF2200BL Input voltage rating 120 V, 60 Hz Input power 13 A Working pressure 2200psi Max. pressure 2500psi Flow rate 1.25GPM (280L/H) Inlet pressure 44psi Supply water temperature (max.) Cold tap water 104oF (40oC) Electrical cord 35ft. (10.7m) High-pressure hose 25ft. (7.
IMPORTANT SAFETY INSTRUCTIONS Please read all of the safety precautions before operating this pressure washer every time. Please pay particular attention to all sections with following symbols. The following signal words and meanings are intended to explain the levels of risk associated with this pressure washer. DANGER! Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
4. Stay alert-watch what you are doing. 5. Do not operate the pressure washer when fatigued or under the influence of alcohol or drugs. 6. Keep operating area clear of all persons. 7. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual. 9. This pressure washer is provided with a Ground Fault Circuit Interrupter built into the power cord plug.
washer. 22. Always follow detergent manufacturer’s label recommendations for proper use of detergents. Always protect eyes, skin and respiratory system from detergent if used. 23. Always lock the trigger of spray gun in the safety position when not in use. 24. Do not use pressure that exceeds the operating pressure of any of the parts (hoses, fittings, etc.) in the pressurized system. Never use with any other manufacturer’s accessories or components. 25.
cords are identified by a marking “Acceptable for use with outdoor appliances; store indoors while not in use.” 2. Use only extension cords having an electrical rating not less than the rating of the pressure washer. 3. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. 4. Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges. 5.
WARNING RISK OF EXPLOSION-DO NOT SPRAY FLAMMABLE LIQUIDS Do not use acids, alkaline, solvents or any flammable material in this product. These products can cause physical injuries to the operator and irreversible damage to the pressure washer. WARNING RISK OF ELECTRIC SHOCK 1. Inspect cord before using –Do not use if cord is damaged. 2. Keep all connections dry and off the ground. 3. Do not touch plug with wet hands. CAUTION GUN KICK BACK 1. Hold with both hands. 2.
INSTALLATION INSTRUCTIONS WARNING! Remove power cord from power source before carrying out any work on the equipment, and use only original parts. Before starting any cleaning task, it is important to inspect the area for objects that could create a hazard. Remove any objects from the work area that could be tripped over, such as toys or outdoor furniture. Ensure that all doors and windows are closed tightly. Fig.5 Fig.6 Unfold the handle As shown in Fig.
Connect the hose to the pressure washer As shown in Fig. 7 Attach high-pressure hose to the washer's water outlet (hand tighten only). Fig.7 Fig.8 Connect the hose and spray gun As shown in Fig. 8 Screw the high-pressure hose firmly onto the spray gun. Fit the spray nozzles to spray gun As shown in Fig. 9 Attach desired color coded spray tip to quick - connect wand by pushing to ensure it is clicked in securely. Insert quick – connect wand into the spray gun, hand tighten until two parts are locked. Fig.
Fig.10 Fig.11 Connect to water supply As shown in Fig. 12 & 13 WARNING! Before carrying out actions below, make sure the ON/OFF switch is on the OFF position. WARING! The pressure washer may not be connected directly to the potable water supply. In this case, use an appropriate back-flow prevention device conforming to the requirements of the American Society of Sanitary Engineers. 1. Connect the water supply hose to water supply. 2. Open the water inlet valve. Fig.12 Fig.
KNOWLEDGE OF SPRAY TIPS As shown in Fig. 14 The spray tips are for purposes as below: T1: Red-0o: Maximum cleaning pressure T2: Yellow-15o: Delivers balanced pressure and flow for general cleaning T3: White-40o: For delicate cleaning T4: Black-Soap: Low pressure / to apply detergent T5: Turbo: To remove particularly stubborn dirt Fig.14 ADJUSTMENT Adjusting the pressure As shown in Fig. 15 This pressure washer is equipped with a pressure regulator. It has four settings.
1. 1015psi; 2. 1305psi; 3. 1595psi; 4. 2200psi; To select the desired pressure Turn knob so the indicator mark aligns with the desired PSI setting. How to make use of the power cord/hose/gun holder As shown in Fig. 16-1&16-2 This pressure washer is equipped with 5 pieces of power cord/hose/gun holder. Each of them consists of three parts ( support and lever, central pin),each lever also could rotate 360 degree around its central pin clockwise or counter-clockwise, can stop in any required position.
OPERATING INSTRUCTIONS Connect to electrical main supply As shown in Fig. 17 DANGER! Before you connect the pressure washer to the power source make sure that the data on the rating plate are identical to the mains data. If possible, do not use extension cords with this pressure washer; however, if you must use one, it must comply with requirement mentioned in section of “IMPORTANT SAFETY INSTRUCTIONS: Insert the power cord into the socket.
Fig.19 Fig.20 CAUTION! Before switching on, first purge pump by squeezing trigger handle for around 5 seconds. To switch the pressure washer on, set the On/Off switch to ON. 1. Unlock the safety trigger lever on the spray gun, and press the trigger lever until there is a steady stream of water. CAUTION! This pressure washer is equipped with soft start function, which controlled by software. After switching on for 10 seconds, the motor will reach to the rated operating speed.
CAUTION ! Risk of pressure washer damage! Never operate the pressure washer without water inlet as dry running may damage the pump. Use a water filter if the inlet water is contaminated. To temporarily store the spray gun As shown in Fig. 21 When fixing the handle to operating position, this pressure washer provides gun holder on right side. Which consist of three pieces power cord/hose/gun holder. It allows to temporarily rest the spray gun on it.
The high-pressure pump starts running as soon as you operate the hand-held spray gun. Due to the soft start function, after switching on for 10 seconds, the motor will reach to the rated operating speed. After releasing the trigger for 10 seconds, the motor can be completely stopped, due to this pressure washer is soft stop function which controlled by software. Use the detergent bottle (not supplied) As shown in Fig. 22 1. Stop the pressure washer. 2. Add detergent to the bottle (not supplied).
CLEANING AND MAINTENANCE Clean the outside of high-pressure washer Clean the pressure washer. Wipe the washer with a slightly damp cloth. Do not clean the pressure washer using a high-pressure water jet. Clean the water filter As shown in Fig. 23 The pressure washer is equipped with a water filter to protect the pump. If the filter is not kept clean, the water flow to the pressure washer will be restricted and the pump may be damaged. To clean water inlet filter, 1.
MOVING AND STORAGE INSTRUCTIONS CAUTION! Before servicing, cleaning, or removal of any part, switch off power and relieve pressure. STORAGE As shown in Fig. 25 & 26 1. Remove the cleaning agent and drain all the water left in the hoses. 2. Clean the high-pressure washer. 3. Fold the handle. 4. Tidy the hose and power cord by winding them around the power cord/hose/gun holder, located on the metal support. 5.
DISPOSAL Disposing of the pressure washer Pressure washers which are labeled with the adjacent symbol must not be disposed of in household garbage. You must dispose of such old electrical and electronic appliances separately. Please check with your local authority about the possibilities for correct disposal. Through separate disposal you send old equipment for recycling or for other forms of re-use. You will thus help to avoid in some cases that damaging material gets into the environment.
Fault/malfunction Pressure washers does not work Pressure too low, but steady Leaks in the Pressure washer Irregular operating pressure The high-pressure washer operates intermittently Cause Remedy No electrical voltage at the device Check the fuse, power cord, power plug and power source and have them replaced by qualified personnel if necessary On/off switch set to "0" On/off switch set to "I" Cross section of the extension Use extension cord with lager cord no large enough and/or the cross se
The motor starts but there is no buildup of pressure No detergent taken in The water filter is clogged Clean the water filter Air intake in the water inlet Check the supply hose and hose connection and replace if necessary Air in the system Ventilate the pressure washer! Run the pressure washer without the pressure washer hose connected until water starts leaking without bubbles. Re-attach the high-pressure hose.
WARRANTY Product Warranty Please keep your original purchase receipt in a safe place as proof of purchase. Warranty coverage for this product must be verified by the original purchase receipt. The warranty period begins on the day that the product was purchased from an authorized retailer of Yard Force products. Warranty coverage only applies to the original purchaser and is not transferrable. Warranty coverage is only provided on products purchased from authorized Yard Force retailers.
Yard Force USA Service Support agents can help you troubleshoot problems over the phone to get you back up and running as quickly as possible. In the situation where service or warranty inspection is needed, please follow these steps: 1. Contact Yard Force USA at (866) 902-9690 Monday-Friday between 8:30 AM and 5:00 PM Eastern Time. 2. Send in proof-of-purchase and serial number (if applicable) to confirm warranty coverage. 3.
