@ Operator's Manu I Single Stage Snow Thrower Models 285 & 295 Models E285 &E295 IMPORTANT: Warning: Read safety rules and instructions This unit is equipped with an internal combustion carefully before operating engine and should not be used on or near any unimproved covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with applicable local or state laws (if any).
TABLEOFCONTENTS Content Page Important Safe Operation Practices .................................................................................. 3 Assembling Your Snow Thrower ....................................................................................... 5 Know Your Snow Thrower ................................................................................................. 6 Operating Your Snow Thrower .....................................................................................
SECTION 1: IMPORTANT SAFEOPERATION PRACTICES ,_ WARNING: This and/or symbol property points out safety instructions which, notinstructions followed, could the personal safety of important yourself and others. Read and followif all in thisendanger manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol--heed its warning.
5. Never runanengine indoors orinapoorly ventilated Maintenance& Storage area.Engine exhaust contains carbon monoxide, an 1. Never tamper with safety devices. Check their proper odorless anddeadly gas. operation regularly. 6. Donotoperate machine whileunder theinfluence of 2. Disengage the auger control bail and stop engine. Wait alcohol ordrugs. until the auger comes to a complete stop. Disconnect the 7. Muffler andengine become hotandcancause aburn.
SECTION2: ASSEMBLING YOURSNOWTHROWER UnpackingFromCarton Cut along comers of the carton and lay it down flat. Remove packing material. Remove any loose parts included with unit (i.e., operator's manual, etc.). Roll unit out of carton. Check carton thoroughly for any remaining loose part. ItemsRequiredForAssembly 1. 2. Engine oil Fresh gasoline NOTE: All references to left or right side of the snow thrower is from the operating position only.
SECTION3: KNOWYOURSNOWTHROWER ,_ WARNING: Be familiar with all the controls on the snow thrower and their proper operation. Know how to stop the machine and disengage them quickly. Recoil Starter Gasoline Cap_ Fuel Plug -_._,__ If Equipped) Access Chute Choke Lever Shave Plat_ Figure 3 Auger ControlHandle Located on the upper handle, the auger control handle is used to engage and disengage the auger. The snow thrower is designed to propel by the rotation of the auger.
SECTION4: OPERATING YOURSNOWTHROWER BeforeStarting _b WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. The spark plug wire was disconnected for safety. Attach spark plug wire to spark plug before starting. GasandOilFill-Up Check oil and gasoline level and add if necessary. Follow related instructions in the separate engine manual packed with your snow thrower. _lb WARNING: Use Gasoline extreme care when handling gasoline.
ToStopEngine To stop engine, turn ignition key counter-clockwise. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended. To help prevent possible freeze-up of starter, proceed as follows: Run engine for a few minutes before stopping to help dry off any moisture on the engine. Electric Starter (If Equipped): Connect power cord to switch box on engine, then to 120 volt AC receptacle.
SECTION5: MAKINGADJUSTMENTS _ WARNING: _ adjustments while the engine is running except where specified in the operator's manual. NEVER attempt to make any ShavePlate To check the adjustment of the shave plate_ place the unit on a level surface. See Figure 6. The wheels, shave plate and augers should all contact level surface. Note that if the shave piate is adjusted toe high, snow may blow under the housing.
SECTION6: MAINTAININGYOURSNOWTHROWER _WARNING: Replacing ShavePlate Before servicing, repairing, or The shave plate is attached to the bottom of the auger housing and is subject to wear. It should be checked periodically. There are two wearing edges and the shave plate can be reversed. Refer to Figure 6. inspecting, disengage the auger control bail and stop eng he. Wa t unt at racy ng paris have come to a complete stop.
SECTION8: TROUBLESHOOTING GUIDE Problem Engine fails to start Cause Remedy 1. 2. Fuel tank empty, or stale fuel Blocked fuel line 1. 2. FilI tank with clean fresh gasoline. Clean fuetline 3. 4. 5. 6. 7. Key not in ON position Spark plug wire disconnected Faulty spark plug Engine not primed Engine flooded with excessive priming 3. 4. 5. Insert key and turn to ON position Connect wire to spark plug. Clean spark plug, readjust gap, or replace. Prime engine four times.
SECTION9: PARTSLISTFORMODELS285, E285, 295 & E295 5048 22 12
Models 285, E285, 295 & E295 REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO, 684_04027 684_04028 710-0134 710-0167 710-0323 710-0352 710-0597 710-0642 710-0896 710-1005 712_0324 712_3010 712_3027 726_0299 731_1033 732_0357A 736_0119 736_0176 736_0326 736_0329 736_3090 741_0600 741_0919 746_04091 748_0234 749_04114 750-04230 REE NO. 28 29 30 31 32 33 DESCRIPTION Auger Ass'y 21" completa w/Solid Shaft Auger Housing Ass'y 21" Screw, 1/4_20 x .
Models 285, E285, 295 & E295 12_ REE NO. PART NO, 1 2 3 4 8 6 7 8 9 10 710-04071 710-0451 712-3068 720-0284 731-04127 731-04353 731-04373 731-04388 731-04429 732-04111 11 12 736-0159 684-04049 I I DESCRIPTION Carriage Screw 5/164 8 x 1.0 Carriage Bolt, 5/16-18 x.075 GR 1 Hex Patch FNut 5/16-18' Handle Knob Assembly 5/16-18 Lower Chute 5" DJa ' Ring_Lower Chute Chute, Adapter 5" Dia Handle-Chute 5" Dia Upper Chute w/Expert LabeJ Chute Adjustment Spring Flat Washer,_349 ID x .879 OD x .
Models 285, E285, 295 & E295 23 4 22 REF. NO. 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 21 22 23 PART NO. 629_0071 710-0157 710-0409 710-0654A 710-0751 710-1003 712_0324 719_0581 726_0205 726_0470 731_2825 736_0119 736_0242 736_0337 747_04169 751_0535 751_0603 751_10023 751_0101A 756_04060 756_0475 790-00047 DESCRIPTION Extension Cord He;
MANUFACTURER'S LIMITED WARRANTY FOR: YaRD'MaNi}// The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its possessions and territories "MTD" warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of odginal purchase and will, at its option, repair or replace free of charge, any part found to be defective in materials or workmanship This limited warranty shall only a