RETRACTABLE SUNSHADE FOR 12 x 12 Pergola room Installation and Operating Instructions – Yp11689X 12 x 12 Pergola Room Sold Separately Yardistry – North America Toll Free Customer Support: 1.888.509.4382 info@yardistrystructures.com www.yardistrystructures.com Yardistry / Selwood Products – Europe Customer Support: +44 1284 852569 parts@selwoodproducts.com www.selwoodproducts.com 3.05 m (10’) 3.66 m (12’) 1 12’ (3.66 m) 10’ (3.05 m) Revised 04/7/2015 HEIGHT: 8’2” or 2.
Important Safety Notice! Yardistry components are intended for privacy, decorative and ornamental use only. Product is NOT INTENDED for the following: • A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds. • As load bearing support for a building, structure, heavy objects or swings. • Used in structures that trap wind, rain or snow that would create extra load on the product. Permanent structures may require a building permit.
Limited Warranty Yardistry warrants that this product is free from defect in materials and workmanship for a period of one year from the original date of purchase. In addition, all lumber is warranted for 5 years against rot and decay. This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure the integrity of your product and is a requirement of the warranty. This warranty does not cover any inspection cost.
Instructions for Proper Maintenance Your Yardistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it. HARDWARE: • • • Check metal parts for rust. If found, sand and repaint using a non-lead paint complying with 16 CFR 1303.
support@yardistrystructures.
Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. ) 7 pc. - Half Rib - Male (Y70819-086) 7 pc. - #5 x 20mm Sheet Metal Screw (Y06490-903) 7 pc. - Half Rib - Female (Y70819-087) 1 pc. - Rib Set (Y70800-089) 2 pc. - Roller Channel Connector (Y70819-023) 1 pc. - Pulley Assembly (2 Pk) (Y70819-024) 1 pc. - Roller Assembly (12 Pk) (Y70890-056) 1 pc. - Roller Channel (4 Pk) (Y70819-046) 1 pc.
Step 1: Inventory Parts - Read This Before Starting Assembly STOP A. STOP STOP STOP his is the time for you to inventory all your hardware, wood and accessories, T referencing the parts identification sheets. This will assist you with your assembly. • Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. B.
Step 2: Roller Channel Assembly A: Insert one Roller Channel on each side of one Roller Channel Connector and attach with two 1/4 x 3/4” Pan Bolts (with two flat washers and one lock nut). Make sure bolts are fully tightened and they are inserted as shown below. Notice smaller holes at ends of Roller Channel. (fig. 2.1, 2.2 and 2.3) B: Repeat for a second Roller Channel Assembly. (fig. 2.1, 2.2 and 2.3) Roller Channel Fig. 2.2 Notice smaller holes at ends Fig. 2.
Step 3: Attach Roller Channel Assemblies to Pergola A: From the inside of each Beam End measure 38-1/8” along both Arch Beam Fronts. (fig. 3.2) B: With a helper attach one Roller Channel Assembly to each Arch Beam Front at the marked out locations with two #12 x 1” Pan Screws (with 1/4” flat washer). (fig. 3.1, 3.2 and 3.3) Fig. 3.1 C: Attach Roller Channel Assembly to Centre Beam and each Arch Beam Offset with three #12 x 1” Pan Screws (with 1/4” flat washer). (fig. 3.2, 3.3 and 3.
Step 4: Attach Eye Bolts A: At one end of each Roller Channel Assembly attach one 3/16” x 1-1/4” Eye Bolt (with 3/16” standard nut, 2 3/16” flat washers and 3/16” lock nut) as shown in fig. 4.1 and 4.2. Make sure the eyebolt does not protrude through the lock nut and the eyebolt faces the direction shown in fig. 4.2. This will be the Back or Fixed Side of the assembly. Front Side Fig. 4.1 Back or Fixed Side Watch for protrusions Roller Channel Assembly 3/16” Lock Nut Fig. 4.
Step 5: Attach Roller Assemblies A: Insert 6 Roller Assemblies into each Roller Channel Assembly, alternating rollers as shown below, 2 roller wheels then 1 roller wheel. (fig. 5.1) Roller Channel Assembly Fig. 5.1 Notice wheel configuration Roller Assembly (x 6 per Roller Channel Assembly) Hardware 12 x Roller Assembly 11 support@yardistrystructures.
Step 6: Attach Fireman Hooks A: Clip one Fireman Hook on each 3/16 x 1-1/4” Eyebolt and each Roller Assembly. There will be 7 Fireman Hooks per Roller Channel Assembly. Notice the orientation of the hooks. (fig. 6.1, 6.2 and 6.3) Fig. 6.1 Roller Channel Assembly Fig. 6.2 Fig. 6.3 Roller Channel Assembly Fireman Hook x 7 per Assembly 3/16” x 1-1/4” Eye Bolt Firerman Hook Hardware 14 x Firerman Hook 12 support@yardistrystructures.
Step 7: Attach Pulley Assembly Part 1 A: Center one Pulley Assembly on the outside face of each Arch Beam Front and attach with two #12 x 1” Pan Screws as shown in fig. 7.1 and 7.2. Arch Beam Front Fig. 7.1 Arch Beam Front #12 x 1” Pan Screw Fig. 7.2 Arch Beam Front Pulley Assembly Hardware 4x #12 x 1” Pan Screw 2x Pulley Assembly 13 support@yardistrystructures.
Step 7: Attach Pulley Assembly Part 2 B: Start feeding the end of the Steel Cable without the loop into the Pulley Assembly on the Front Side, around the disc and out the other side and into the Pulley Assembly on the Back or Fixed Side and then out the other side of the pulley as shown in fig. 7.3. C: Unscrew the Turnbuckle then place the Cable to Rib Connector (opening facing inwards) over the end of the Steel Cable with the loop then attach the loop to the open hook on the Turnbuckle. (fig. 7.4, 7.
Step 8: Insert Ribs into Canopy Part 1 A: Insert one 1/2 Rib Male into one 1/2 Rib Female so the holes align then attach with one #5 Screw. Complete 7 times to make 7 Rib Assemblies. (fig. 8.1, 8.2 and 8.3) 1/2 Rib Female Fig. 8.1 1/2 Rib Male Align holes 1/2 Rib Female Fig. 8.3 Fig. 8.2 Rib Assembly 1/2 Rib Male #5 x 20mm Sheet Metal Screw Hardware 7 x #5 x 20mm Sheet Metal Screw 15 Other Parts 7 x 1/2 Rib Male 7 x 1/2 Rib Female support@yardistrystructures.
Step 8: Insert Ribs into Canopy Part 2 B: Place one Rib Assembly into each tunnel opening in the 12’ x 12’ Retractable Canopy and feed all the way through so the Rib Handles fit through the top openings. If the opening is tight use a screw driver to help insert the Rib Assembly. (fig. 8.4, 8.5, 8.6 and 8.7) Note: All arches to be facing up. 12’ x 12’ Retractable Canopy Fig. 8.4 Cut-out Openings Cut-out Opening 12’ x 12’ Retractable Canopy Fig. 8.5 Rib Assembly Fig. 8.6 Rib Hanger Fig. 8.
Step 9: Attach Canopy to Fireman Hooks A: Attach Crank Handle to hook on one Pulley Assembly, it can be attached to either end. (fig. 9.1) B: With a helper lift 12’ x 12’ Retractable Canopy to Pergola Room and ribs to each Fireman Hook on both Roller Channel Assemblies with the Rib Hangers. (fig. 9.2) Fig. 9.1 Pulley Assembly Crank Handle Roller Channel Assembly Fig. 9.2 Fireman Hook 12’ x 12’ Retractable Canopy Rib Hanger Hardware 1x Crank Handle 17 support@yardistrystructures.
Step 10: Attach Canopy to Catch A: Tighten the Turnbuckle so it is snug. If it is too loose the cable will spin in the Pulley Assembly, if it is too tight the pulley will not turn. (fig. 10.1) B: Fully open 12’ x 12’ Retractable Canopy, place Cable to Rib Connector over first Rib Assembly and secure with one #12 x 1” Pan Screw. (fig. 10.2) Note: Remove the Canopy prior to snow or heavy winds by removing the screws from the Cable to Rib Connector and removing the Canopy from the Fireman’s Hooks. Fig.
NOTES 19 support@yardistrystructures.
YARDISTRY Consumer Registration Card First Name Initial Last Name Street Apt. No.
