Installation Manual Privacy Screen with Planters YM11615 Yardistry Mount Forest, ON Canada N0G 2L0 Toll Free Customer Support: 1.888.509.4382 info@yardistrystructures.com www.yardistrystructures.
Important Safety Notice! • Yardistry components are intended for privacy, decorative and ornamental use only. Product is NOT INTENDED for the following: - A safety barrier to prevent unsupervised access to pools, hot tubs, spas, or ponds. - Safety railings for elevated platforms or decks. - As load bearing support for a building, structure, heavy objects or swings. - Used in structures that trap wind, rain or snow that would create extra load on the product. Wood is NOT flame retardant and will burn.
Instructions for Proper Maintenance Your Yardistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it. HARDWARE: • • • Check metal parts for rust. If found, sand and repaint using a non-lead paint complying with 16 CFR 1303.
are approximate and are shown to assist in the identification of parts for assembly. Part Identification ( Dimensions ) Actual dimensions may be smaller or larger. 018 020 019 1pc. - Planter Screen B - Y70119-020 38.1 x 520.7 x 1676.4mm 1pc. - Planter Screen AL - Y70119-018 38.1 x 520.7 x 1676.4mm 1pc. - Planter Screen AR - Y70119-019 38.1 x 520.7 x 1676.4mm 016 017 4pc. - Inside Wall - Planter Box - Y70119-017 38.1 x 250.8 x 419.1mm 4pc. - Outside Wall - Planter Box - Y70119-016 38.1 x 250.
Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 56pc. - Wood Screw #6 x 1-1/8" - (Y06420-914) 32pc. - Pan Screw #6 x 5/8" - (Y06420-908) 48pc. - Wood Screw #8 x 1-1/2" - (Y06420-512) 12pc. - Wood Screw #10 x 1" - (Y06420-710) 16pc. - Wood Screw #8 x 2-1/2" - (Y06420-522) 12pc. - Wood Screw #8 x 3" - (Y06420-530) 8pc. - Corner Brace - Planter Box (Y70890-005) 6pc.
Step 1- Attach inside Walls A. Attach 1 (142) Base Board End to the ledge of the (017) Inside Wall Assemblies, using 4 (YS27) #6 x 1-1/8” wood screws as shown below. Be sure it is flush to the edge. (Fig. 1.1 and 1.2) B. Attach 2 (143)T&G Base Board to the ledge of the (017) Inside Wall Assemblies, using 4 (YS27) #6 x 1-1/8” wood screws per board. (Fig. 1.1) C. Attach 1 (136) T Base Board to the ledge of the (017) Inside Wall Assemblies, using 4 (YS27) #6 x 1- 1/8” wood screws per board.
Step 2 - Attach outside walls A. Flush to the outside of (017) Inside Wall Assembly, attach 2 (016) Outside Wall Assembly using 4 (YS3) #8 x 2-1/2” wood screws per assembly as shown below. Repeat for 2 assemblies Flush to outside of Inside Wall Assembly 017 Notice hole location. YS3 x8 016 Flush to outside of (017) Inside Wall Assembly 4x 016 16 x Outside Wall Assembly (38.1 x 250.8 x 417.
Step 3 - Attach supports to box A. Place 2 (135) End Supports and 1 (146) Base Support as shown in Fig. 3.1 and attach using 1 (YS4) #8 x 3” wood screw through each (016) Outside Wall Assemblies. (Fig. 3.1) B. Then from the inside of the box, secure with 8 (YS27) #6 x 1-1/8” wood screws. (Fig. 3.2) Repeat for 2 assemblies Fig. 3.1 May have to loosen these screws for the supports to fit 146 YS4 Fig. 3.
Step 4 - Attach Frame stiles to box A. Attach 4 (133) Frame Stiles flush to the edge of (016) Outside Wall Assembly using 2 (YS2) #8 x 1-1/2” Wood Screws per Frame Stile. B. Secure the (017) Inside Wall Assemblies to the (133) Frame Stile from the inside using 4 (YS27) #6 x 1-1/8” wood screws. Repeat for 2 assemblies 016 Flush to edge of Outside Wall Assembly 016 016 Flush to edge of Outside Wall Assembly 133 x4 YS27 x4 YS2 016 8x 133 Frame Stile (19.1 x 63.5 x 250.
Step 5 - Attach corner braces A. Attach 4 (005) Corner Braces to each (017) Inside Wall Assembly and (016) Outside Wall Assembly as shown below. Use 4 (YS13) #6 x 5/8” Pan Screws per (005) Corner Brace, ensuring that they are flush to the bottom.
Step 6 - assemble screens A. Before assembling the screens, determine what the final orientation will be. B. Place 2 of the screens side by side as shown in Fig. 6.1 and 6.2, and attach 3 Hinges to the Planter Screens using 2 (YS28) #10 x 1” Wood Screws per hinge. Ensure that the hinges are flush to the edge of the groove. Repeat on opposite side. Keep in mind that the hinge pivot is to be located on the same side that the screen opens toward. (Fig. 6.3) 018 020 019 Fig. 6.1 Fig. 6.
Step 7 - Attach Planter Box A. Determine Planter Box orientation. B. Install Planter Box Rails according to desired orientation. C. Once you decide which orientation you will be using (i.e Planter Box Centred or Planter Box Offset), attach 8 (134) Frame Rail to the (017) Inside Assemblies as shown below, using 2 (YS2) #8 x 1-1/2” wood screws per Frame Rail Adjustable. Planter Box Centred Note: Frame Rail Adjustable must be flush to both Frame Stile as shown. Leave 1-5/8” in between Frame Rail Adjustable.
Step 8 - Attach Planter Boxes to Planter Screens And Place Box Liner 1. Attach Planter Boxes to Planter Screens using 4 (YS4) #8 x 3” Wood screws per Planter Box as shown below. 2. Place 1 Box Liner into each assembled Planter Box. Be sure to note that the shoulder on the box liner fits under the Panel Rails. Note: Fill with dirt immediately to prevent wind blow over. YS4 4 per Planter Box Box Liner The shoulder on the box liner fits under the panel rails.
