2’ x 20° MERIDIAN WOOD GAZEBO with ALUMINUM ROOF Installation and Operating Instructions — YM11775 HEIGHT: 3.099 m/ 102" IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY 04-07-2021 Artistry — North America Toll Free Customer Support: 1.888.509.4382 www.yardistrystructures.com \.
A\Important Safety Notice! Artistry components are intended for privacy, decorative and ornamental use only. Product is NOT INTENDED for the following: « A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds. « As load bearing support for a building, structure, heavy objects or swings. « Used in structures that trap wind, rain or snow that would create extra load on the product. Accumulated snow must be removed from roof. DO NOT climb or walk on roof for any reason.
Limited Warren This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states/provinces do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.
Instructions for Proper Maintenance Your Artistry structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you, the owner, properly maintain it. HARDWARE: + Check metal parts for rust. If found, sand and repaint using a non-lead paint complying with 16 CFR 1303. + Inspect and tighten all hardware after completion of assembly; after first month of use; and then annually.
Assembly Tips Following are some helpful tips to make the assembly process smooth and efficient. PER-ASSEMBLIES: (i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc) « Work on a raised, solid and flat surface such as, a table or saw horse. « Keep all connections flush where shown in the instructions. + When assembling the beams keep parts flat, straight and snug when connecting. METAL PARTS: + Roofing material may have sharp edges, wear safety gloves.
Permanent Installation Examples Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Pergola Room. We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure to a per-existing or new wood or concrete surface. = The hardware to attach the Post Mount to the structure is included.
Permanent Installation Examples cont. Concrete Patio [min. 3.616 (11° x 20’ with 15.24 cm (6") clearance on all sides Cm Wood Deck [min. 3.616 (11° x 20’ 7/8”] with 15.24 cm (6") clearance on all sides Post Mount Anchoring Hardware {not included) Post Mounts have a 12.7 mm diameter hole for anchoring hardware.
Fi 1 Dimensions are approximate and are shown to assist in the identification of parts for Part Identification assembly. ACh dimensions may be smaller or larger. ) mmm, 6pc. (705) Gusset RT 1015mm Y70131-706 : | Y50131422 6pc. (706) Gusset LT 1015mm 24pc. (422) Plinth Ey 1727) 2pc. (1003) Baal Short Right 1763.3mm 50131-1003 2pc. (1002) Beam Short Left 1763.3mm ( ° | Ys0131-1002 ! 4pc. (1004) Beam Short End 555.4mm T T {| : 2pc. (1005) Beam Short Center 2422. 1mm Y50131-1005 hair 2pc.
Hardware Identification ( Dimensions are approximate and are shown fo assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 4pe. Short Panel Left {Y01033-200) 4pe. Long Panel Right (Y01033-187) 8pc. Middle Panel (Y01033-196) bh. 1pc. Roof Panel Set 4pe. Long Panel Left 4pc. Short Panel Right P (Y01033-198) {Y70833-203) (Y01033-199) t 1 4pc. Roof Edge Left 72.2 (Y01033-134) E 4pc. Roof Edge Right 72.2 (Y01033-135) T 7 8pe. Ridge Clip 102.5 (Y01033-133) T 7 8pc.
Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. dpe. pe. Roof Peak Sef Roof Peak Bracket (Y70829-202) (Y00429-125) 14 F Nut Spc. Peak Post robes 200 pity EE 9? spring Ci Post Lip ° ring Cli eal C: Bolt iid ARTS) Saneness 1pe. Peak Cap Center 3pc. Peak Bracket (Y00429-190) [200 oak Cap Delta | (Y01033-347) = ape. oof of Edge (Monotone I) 1pe. 45° Twist Bracket LT .
Step 1: Inventory Parts Read This Before Starting Assembly This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. » Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. B. If there are any missing or damaged pieces or you need assistance with assembly please contact the consumer relations department directly.
Step 2: Post Assemblies A: At the bottom of one (696) 6 x 6 Post insert one 5/16” T-Nut on the outside of two sides, as shown in F2.3. B: At the bottom of the same (696) 6 x 6 Post place two Post Mounts tight to the bottom and inside faces on the sides as shown in F2.1 and F2.2. Loosely attach with one 5/16 x Hex Bolt (with 5/16” lock washer and 1/45/16" large washer) per mount so they connect to the T-Nuts. From the bottom attach with two #8 x Wood Screws and two #10 x Pan Screws per mount. Tighten bolts.
Step 3: Short Beam Assembly Part 1 A: Connect one (1002) Beam Short Left and one (1003) Beam Short Right using two 5/16 x Hex Bolts {with 5/16" lock washer, large washer and 5/16” t-nut) as shown in F3.1 and F3.2. B: Connect one (1004) Beam Short End to each end of one (1005) Beam Short Center using two 5/16 x Hex Bolts (with 5/16” lock washer, large washer and 5/16" t-nut) per end as shown in F3.1 and F3.2.
Step 3: Short Beam Assembly Part 2 D: Place one Short Beam L-R Assembly tight to one Short Beam End Assembly so the ends are flush. Match the bolt holes in each (1004) Beam Short End with the bolt holes in (1002) Beam Short Left and (1003) Beam Short Right. Attach with 18 #8 x Wood Screws. (F3.3 and F3.4) E: Repeat Step D one more time to make two Short Beam Assemblies. n—_ > } (1003) Beam F3.
Step 4: Long Beam Assembly Part 1 A: Connect one (694) Outer End to each end of one (693) Outer Beam Center using four 5/16 x Hex Bolts (with 5/16" lock washer, large washer and 5/16" t-nut) as shown in F4.1 and F4.2. Notice orientation of angled ends. B: Connect one (692) Beam Long End to each end of one (691) Beam Long Inside using four 5/16 x Hex Bolts (with 5/16" lock washer, large washer and 5/16" t-nut) as shown in F4.3 and F4.4. Notice orientation of angled ends. (693) Outer Beam Irenic F4.
Step 4: Long Beam Assembly Part 2 D: Place one Outer Beam Assembly and one Inside Beam Assembly together so the beam assembly ends are flush and the angled ends match. Bolt heads must be on the outside of both beam assemblies. Match the bolt holes in (691) Beam Long Inside and each (692) Beam Long End with the bolt holes in each (694) Outer End then attach with 24 #8 x Wood Screws. (F4.5 and F4.6) E: Repeat Step D to make a second Long Beam Assembly. F4.5 Inside Beam Assembly Notice orientation.
Step 5: Frame Assembly and Anchoring Q Part hard, flat surface place one Short Beam Assembly against the outside of two Post Assemblies, flush to the tops and outside comers. Attach Beam to Post, through the bottom hole, with one 3/8 x Hex Bolt (with two 3/8” large washers and one 3/8” lock nut) per Post. (F5.1 and F5.2) The distance from the outside of one Post Assembly to the outside of the second Post Assembly should be 10’ 103/8". See F5.3 for accurate positioning of Posts.
Step 5: Frame Assembly and Anchoring 3) Part 2 = Note: The beveled ends on each gusset should always face away from the wood it Is attaching to. C: Make sure each Short Side assembly is square with the Post Assembly then facing one Short Beam Assembly from the outside place one (705) Gusset RT on the right hand side so the top fits tight to the Beam Assembly and the bottom fits tight to the Post Assembly.
Step 5: Frame Assembly and Anchoring (BK) ¥ Part 3 v F: Move your Post Assemblies to the final location. Make sure the ground is flat and level before continuing assembly. G: With helpers stand up Short Beam Assemblies then place one Long Beam Assembly against the outside of two Post Assemblies, flush to the tops and outside corners and tight to Short Beam Assembly.
Step 5: Frame Assembly and Anchoring Part 4 H: From inside the assembly, center one Post Assembly over middle bolt holes in each Long Beam Assembly then place Steel Cable with Bracket against both Post Assemblies so the angle of the bracket faces up and is over the top bolt hole. Attach Long Beam Assembly to Post Assembly and Steel Cable with Bracket through the top hole with one 3/8 x Hex Bolt (with two 3/8" large washers and one 3/8" lock nut). (F5.9 and F5.10) Steel Cable Long Beam Assembly 3/8 x F5.
Step 5: Frame Assembly and Anchoring Part 5 Note: The beveled ends on each gusset should always face away from the wood it Is attaching to. I: Make sure the Frame Assembly is square and level then facing one Long Beam Assembly from the outside place one (705) Gusset RT on the right hand side Post Assembly and one on the left side of the middle Post Assembly so the tops fit tight to the Beam Assembly and the bottom fits tight to the posts.
Step 5: Frame Assembly and Anchoring AFR Part 6 L: Attach Long and Short Beam Assemblies to outside Post Assemblies with two 5/16 x Lag Screws (with large washer) per corner in the remaining holes. (F5.13) M: Attach Long Beam Assembly to both Post Assemblies through the bottom holes with one 5/16 x Lag Screw (with large washer) per post. (F5.14) N: Depending on what you are placing the Gazebo on will determine how you anchor it to that surface. Please refer to pages 6 and 7 for installation examples.
Step 6: Attach Brackets A A: On each middle Post Assembly place one Center Roof fo Beam Bracket, centered fo each Long Beam Assembly so they are flush and tight to the inside face of each beam then attach to Post Assemblies with two #12 x Pan Screws per bracket. (F6.1 and F6.2) Long Beam Assembly 4x #12 x Pan Screw 2x Center Roof to Beam Bracket 26 supportgRyardistrystiuciurss.
Step 7: Fascia Beam Assembly Small Roof Rafter A: Tightly connect one (627) Fascia Left Short and one (628) Fascia Right Short using one 5/16 x Hex Bolt (with 5/16" lock washer, large washer and 5/16” t-nut) as shown in F7.1 and F7.2. Repeat to make a second Fascia Beam Assembly. 51¢° T-nut Large Wash: hay F7.
Step 8: Small Roof Assembly Part 1 A: On each side of one (634) Rafter place one (624) Rafter Comer Left and one (623) Rafter Comer Right so the tops and edges are flush then attach with two #8 x Wood Screws per side. (F8.1 and F8.2) B: Place Fascia Beam Assembly from Step 7 on the bottom of (624) Rafter Comer Left, (623) Rafter Comer Right and (634) Rafter so the sides are flush then attach with one #8 x Wood Screw at each end and one in the middle. (F8.1, F8.3, F8.4 and F8.
Step 8: Small Roof Assembly Part 2 D: Place one (629) Rafter Short RT, one (632) Rafter Center RT, one (631) Rafter Center LT and one (630) Rafter Short LT over the pilot holes in the Fascia Beam Assembly so they are flush to the top of the assembly and tight to both (623) Rafter Comer Right and (624) Rafter Comer Left, as shown in F8.6. Attach Fascia Beam Assembly to rafters with one #8 x Wood Screw per rafter. Repeat for second Small Roof Assembly. (F8.6, F8.7 and F8.8) (624) Rafter F8.
Step 8: Small Roof Assembly Part 3 E: Place one (636) Top Strap, one (637) Mid Strap, one (687) Bottom Strap LT and one (688) Bottom Strap RT in the notches of each rafter so the ends do not overhang the outside edges of the outside boards. (687) Bottom Strap LT and (688) Bottom Strap RT sit tight together. Attach with four #8 x Wood Screws per strap. Complete for each Small Roof Assembly. (F8.9, F8.10 and F8.
Step 8: Small Roof Assembly Part 4 F: Attach (629) Rafter Short RT and (632) Rafter Center RT to (623) Rafter Comer Right and (631) Rafter Center LT and (630) Rafter Short LT to (624) Rafter Comer Left with two #8 x Wood Screw per rafter. (F8.11 and F8.12) G: Attach (636) Top Strap, (637) Mid Strap and (687) Bottom Strap LT to rafters with 16 #8 x Wood Screws. (F8.13) (623) Rafter H: Complete Steps F and G for both Small Roof Assemblies.
Step 9: Attach Officiants Small Roof Assembly A: Tum over each Small Roof Assembly then place two (648) Officiants tight together at center of (634) Rafter and tight to the top of Fascia Beam Assembly. Attach (648) Officiants to (634) Rafter, (623) Rafter Comer Right, (624) Rafter Corner Left, (629) Rafter Short RT, (630) Rafter Short LT, (632) Rafter Center RT and (631) Rafter Center LT with four #8 x 1” Pan Screws per offsite. (F9.1 and F9.2) F9.
INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! HANDLE WITH CARE! Place roofing material on a non-abrasive surface before assembly as it can bend, dent and scratch easily. WARNING —DO NOT OVER TIGHTEN ROOFING SCREWS! Over tightening screws will cause roofing material to crush. Over lightened and Crushed Snug and Tight The roofing screws can easily crush the Roof Panels and Roof Edges when using a power drill.
INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! BE SURE TO REMOVE ALL PLASTIC COVERING, ON BOTH SIDES OF THE ALUMINUM PANELS AND TRIM, DIRECTLY BEFORE INSTALLING EACH PIECE. (One side is clear and the other is blue, both must be removed.
Step 10: Attach Roof Panels Small Roof Assembly art 1 ne Small Roof Assembly so it is flush to the side of (624) Rafter ia Beam Assembly. old line ith A: Pi Com Cel les sh up wi (634) Left and sh to th side at th m Ashe 10.1, F10 ding Screws in locate Screws. D: Flush = A Slight overhang L Flush on (624) Raft Come Lt \ Flush:
Step Jo: Attach Roof Panels Small Roof Assembly al E: Place one Short Panel Left on Small Roof Assembly so it overlaps the Long Panel Left and it is flush to the sides of (624) Rafter Comer Left and a slight overhang at the bottom of the Fascia Beam Assembly. There should be no overhang at the corners. (F10.4 and F10.
Step 11: Attach Ridge Clips and Roof Edges Small Roof Q A: Place one Roof Edge Left 72.2 and one Roof Edge Right 72.2 on the bottom of each Small Roof Rafter Assembly so the ends are flush with the outside ends of the Fascia Beam Assembly and meet tight in the center. Attach both Roof Edges with Roofing Screws per Small Roof Rafter assembly. (F11.1 and F11.2) B: Place one Weather Seal on the inside of four Ridge Clip 102.5 then place one Ridge Clip 102.
Step 12: Corner Roof Assemblies Part 1 A: On the left side of one (675) Middle Rafter place one (624) Rafter Comer Left so the tops and edges are flush, notice on the (675) Middle Rafter the angled end at the bottom slopes down then attach with two #8 x Wood Screws. Repeat this step by attaching one (623) Rafter Comer Right on the right side of one (675) Middle Rafter. (F12.1, F12.2 and F12.
Step 12: Corner Roof Assemblies Part 2 D: For each Right Comer Roof Assembly and each Left Comer Roof Assembly, place one (629) Rafter Short RT, one (632) Rafter Center RT, one (631) Rafter Center LT and one (630) Rafter Short LT over the pilot holes in the (677) Right End Fascia and (676) Left End Fascia so they are flush to the top of the assembly and tight to both (623) Rafter Corner Right and (624) Rafter Corner Left, as shown in F12.6 and F12.7.
Step 12: Corner Roof Assemblies Part 3 E: For each Left Corner Roof Panel place one (681) Left Top Strap, one (683) Left Mid Strap and one (685) Left Bot Strap in the notches of each rafter so the ends do not overhang the outside edges of the outside boards then attach with four #8 x Wood Screws per strap. (F12.10 and F12.
Step 12: Corner Roof Assemblies Part 4 G: Attach (629) Rafter Short RT and (632) Rafter Center RT to (623) Rafter Comer Right and (631) Rafter Center LT and (630) Rafter Short LT to (624) Rafter Corner Left with two #8 x Wood Screw per rafter. (F12.13, F12.14 and F12.15) H: Attach (684) Right Mid Strap and (686) Right Bot Strap to (629) Rafter Short RT and (632) Rafter Center RT; and (683) Left Mid Strap and (685) Left Bot Strap to (630) Rafter Short LT and (631) Rafter Center LT with 12 #8 x Wood Screws.
Step 13: Attach Officiants Corner Roof Assemblies A: Tum over each Comer Roof Assembly then place one (690) Offsite End tight to the top of each (676) Left End Fascia and each (677) Right End Fascia. Each (690) Offsite End must be flush with the outside edge of (675) Middle Rafter.
Step 14: Attach Roof to Beam Brackets Corner Roof Assemblies A: Turn the assemblies back over then on the back of each Comer Roof Assembly, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to (629) Rafter Short RT, (632) Rafter Center RT, (630) Rafter Short LT and (631) Rafter Center LT with one 1/4 x 2" Hex Bolt (with two large washers and one 1/4” lock nut) per bracket. (F14.1, F14.2, F14.3 and F14.4) F14.
Step 15: Attach Roof Panels Corner Roof Assemblies IMPORTANT: Before starting this step, be sure fo refer back to pages 33 & 34 regarding correct installation and handling of the roofing. A: On the front of each Left Comer Roof Assembly place one Long Panel Left and one Short Panel Left so they are flush to the side of (624) Rafter Corner Left and the rib of Long Panel Left is center on (675) Middle Rafter. There will be a slight overhang at the bottom of the (676) End Fascia Left.
Step 16: Attach Roof Edges Corner Roof Assemblies A: On the bottom of each Left Corner Roof Assembly place one Roof Edge Left 72.2 so the holes in the Roof Edge Left line up with the holes in the panels then attach Roof Edges with nine #8 x 17 Roofing Screws per Left Comer Roof Assembly. (F16.1 and F16.3) B: On the bottom of each Right Comer Roof Assembly place one Roof Edge Right 72.
Step 17: Attach Ridge Clips Corner Roof Assemblies Q A: Place one Weather Seal on the inside of four Ridge Clip 102.5 then place one Ridge Clip 102.5 on each (623) Rafter Comer Right and each (624) Rafter Corner Left so they cover the panels and are flush to the top, then attach with five #7 x 3/4" Wood Screws per Ridge Clip 102.5. Bottom edge of Ridge Clip 102.5 should be up from the bottom edge of Rafter Corners Left and Right. (F17.1, F17.2, F17.3 and F17.
Step 18: Large Roof Assembly Part 1 A: On each side of one (680) Rafter Top place one (675) Middle Rafter so the tops and edges are flush then attach with two #8 x Wood Screws per side. (F18.1 and F18.2) B: Place one (678) Mid Fascia on the bottom of each (675) Middle Rafter so the sides and top are flush then attach with one #8 x Wood Screw at each end. (F18.1, F18.3 and F18.4) C: Repeat Steps A and B to make a second Large Roof Assembly.
Part 2 D: Place five (633) Center Rafters over the pilot holes in (678) Mid Fascia and (680) Rafter Top so they are flush to the top of each board, as shown in F18.5. Make sure (633) Center Rafters are square to (678) Mid Fascia and {680) Rafter Top then attach (680) Rafter Top to rafters with two #8 x Wood Screws per rafter and (678) Mid Fascia to rafters with one #8 x Wood Screw per rafter. Repeat for second Large Roof Assembly. (F18.5, F18.6, F18.7 and F18.8) Step 18: Large Roof Assembly L ] F18.
Step 18: Large Roof Assembly Part 3 Q E: Place three (679) Center Straps in the notches of each (675) Middle Rafter and each (633) Center Rafter so the ends are flush to the outside edges of (675) Middle Rafters. Make sure assembly is square then attach with 14 #8 x Wood Screws per strap. Repeat for second Large Roof Assembly. (F18.9, F18.10 and F18.11) F18.9 (880) Rafter Top NTR ATTN ATTN ND Ni NL FINN Middle (633) Center (678) Mid Rafter Rafter Fascia #8 x Wood Screws x 14 per strap Nose ea Nom SG F18.
Step 18: Large Roof Assembly Part 4 F: Tum over each Large Roof Assembly then place one (689) Offsite tight to the top of (678) Mid Fascia (689) Offsite must be flush with the outside edge of (675) Middle Rafter. Attach (689) Offsite to each (675) Middle Rafter and each (633) Center Rafter with seven #8 x 1” Pan Screws. Install (689) Offsite on both Large Roof Assemblies. (F18.11 and F18.
Step 19: Attach Roof to Beam Brackets Large Roof Assemblies A: On the back of each Large Roof Assembly, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to the two outside (633) Center Rafters with one 1/4 x 2" Hex Bolt (with two large washers and oneness” lock nut) per bracket. (F19.1 and F18.2) Roof to Beam F19.2 1/4" Lock Bracket Back View Nut 3 ~~ (633) Center Rafter “.
Step 20: Attach Roof Panels Large Roof Assemblies Part 1 = Q IMPORTANT!: Before starting this step, be sure to refer back to pages 33 & 34 regarding correct Installation and handling of the roofing. A: Tum over Large Roof Assemblies, make sure they are still square. Place four Middle Panels flush to the top and sides of (680) Rafter Top and (675) Middle Rafter. There will be an overhang at the bottom over (678) Mid Fascia. The panels overlap and screw holes line up as shown in F20.4.
Step 21: Attach Roof Edges Large Roof Assemblies A: On the bottom of each Large Roof Assembly place one Ridge Edge Middle so the holes line up with the holes in the Middle Panels then attach with Roofing Screws per Large Roof Assembly. (F21.1 and F21.
Step 22: Attach Ridge Clips Large Roof Assemblies Q@ A: Place one Weather Seal 75-1/2 on the inside of four Ridge Clip 73.5 then place one Ridge Clip 73.5 on each {675) Middle Rafter on both Large Roof Assemblies so they cover the panels and are flush to the tops. The bottom edge of each Ridge Clip 73.5 should be up from the bottom edge of (675) Middle Rafter. Attach with four #7 x 3/4” Wood Screws per Ridge Clip 73.5. (F22.1, F22.2 and F22.3) Top F222 Weather Seal 75-172 Components: 4 x Ridge Clip 73.
Step 23: Attach Large Roof Assemblies to Frame (AT§) Part 1 A: With all four assemblers lift Large Roof Assembly with Spacers centered on the Long Beam Assembly so the middle (633) Center Rafter fits in Center Roof to Beam Bracket on middle Post Assembly. Loosely attach Center Roof to Beam Bracket to (633) Center Rafter with one 1/4 x 2” Hex Bolt (with two large washers and one 1/4” lock nut). (F23.1 and F23.
Step 23: Attach Large Roof Assemblies to Frame (R$ 88) Part 2 D: From the outside of the assembly have one person push one Large Roof Assembly in so (689) Offsite fits tight to the Long Beam Assembly and two people pushing up at the peak. One person fastens each Roof to Beam Bracket to beam and then rafters with three #12 x Pan Screws. Install top screw into (633) Center Rafter first then other two into the beam. Repeat this process for the second Large Roof Assembly. (F23.5 and F23.
Step 24: Place Peak Cap Assembly on Roof Panels Part 1 A: Slide one Peak Cap Detail in each end of Peak Cap Center and attach with three 1/4 x 1/2” Pan Bolts {with 1/4" lock nut) per side. (F24.1 and F24.2) Peak Cap Center F241 Peak Gap Detail 14x12 Pan Bolt Peak Cap Detail Peak Cap Center 1/4" Lock Nut Components: Hardware 2 x Peak Cap Detail 1/2” Pan Bolt {1/4” lock nut) 1 x Peak Cap Contra 58 supportgRyardistrystiuciurss.
Step 24: Place Peak Cap Assembly on Roof Panels 1 Part 2 B: Insert five Carriage Bolts with Contoured Washers through the top of Peak Cap Assembly. Place one Peak Post over each Carriage Bolt and secure with Spring Clips. The Spring Clip holds the assembly together. (F24.3, F24.4 and F24.5) C: With one person on each end of the roof place Peak Cap Assembly on top of Large Roof Assemblies so Carriage bolts with Peak Post fit through gaps between the roof assemblies. (F24.
Step 2: Attach Corner Roof Assemblies to Frame (AT§) 1 art A: Place Left Corner Roof Assemblies on the left side of each Large Roof Assembly and the Right Comer Roof Assemblies on the right sides. You will need to lift Peak Cap Assembly to get the top under it. Make sure fascia on each panel are flush then attach (675) Middle Rafters from each connecting assembly with four 1/4 x 3° Hex Bolts {with two large washers and one 1/4” lock nut) per Comer Roof Assembly. (F25.1 and F25.
Step 25: Attach Corner Roof Assemblies to Frame (AT§) Part 2 C: On each connecting (675) Middle Rafter on the Large Roof Assembly attach one Beam to Rafter Bracket per rafter using four #12 x Pan Screws per bracket. (F25.4, F25.5 and F25.6) D: Tighten all Bracket bolts in the Corner Roof Assemblies. Large Roof (675) Middle Assembly ar Long Beam Assembly Safer Bracket r Bran! (675) Middle Comer Roof F25.5 Rafter Assembly Large Roof EAN VY #12x 1-112 \ Pan Screw Ny [0] Beam to ° Rafter Bracket Long Beam Long
Step 26: Attach Small Roof Assemblies to Frame (8) A: With all four assemblers lift one Small Roof Assembly up and over the Short Beam Assembly. You will need to lift the Peak Cap Assembly to get the top under it. Loosely attach each (623) Rafter Comer Right to each (624) Rafter Corner Left with three 1/4 x Hex Bolts (with two large washers and one 1/4” lock nut) per side. To align bolt holes helper in the center may have to push up the center of the panels and others make sure corners are aligned.
Step 27: Secure Roof Corners A 1 A: From outside the assembly attach Small Roof Assemblies and Corner Roof Assemblies together at the Fascia Beam Assembly and Left and Right End Fascias with two #8 x Wood Screws per corner. A helper may need to lift the center of the roof to bring the comers tight together. (F27.1 and F27.2) Fascia Be (677) Right ho or End Fascia (676) Left End Fascia (676) Left ¥) End Fascia Fascia Beam (677) Right End Fascia Fascia Beam ly F27.
Step 28: Attach Corner Caps each corner place one Comer Cap tight to Fascia Assemblies and End Fascias, push up so the bottom is tight to the bottom of the fascia then attach with four #8 x 3/4" Sheet Metal Screws per Corner Cap. (F28.1 and F28.
Step 29: Attach Roof to Beam Brackets Small Roof Assembly A: On each Small Roof Assembly, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to each rafter with one 1/4 x 2” Hex Bolt (with two large washers and oneness” lock nut) per bracket. (F29.1 and F29.2) B: Push panels up from the outside and inside top to make sure each (648) Offsite is tight to the Short Beam Assemblies then fasten each Roof to Beam Bracket with three #12 x Pan Screws per bracket.
Step 30: Attach Ridge Caps to Roof Panels (A) Lu Part 1 A: At each comer, slide one Ridge Cap Long 81.5 over the Ridge Clips, from the bottom up with cut end leading. (F30.1 and F30.2) B: Slide Ridge Cap Short 25.2 over the Ridge Clips leading with the insert end to push the Ridge Cap Long 81.5 to the top, lifting Peak Cap Assembly so Ridge Cap Long 81.5s fit under. Attach with two #8 x 3/4” Sheet Metal Screws per Ridge Cap set. (F30.1, F30.3, F30.4 and F30.5) Ridge Clip Peak Cap Assembly Ridge Cap Long 81.
Part 2 C: Remove the #8 x 1” Roofing Screws from each Ridge Edge Left, Ridge Edge Middle and Ridge Edge Right where each Corner Roof Assembly and each Large Roof Assembly connect. Two screws per location. (F30.6 and F30.7) Step 30: Attach Ridge Caps to Roof Panels (A) D: Place one Roof Edge Center over each connecting seam, tight to Ridge Edges and attach with previously removed screws. (F30.6 and F30.
Step 30: Attach Ridge Caps to Roof Panels (A) Part 3 E: At each Comer Roof Assembly and Large Roof Assembly connection, slide one Ridge Cap Middle over the Ridge Clips, from the bottom up to the top, with cut end leading. Slide under Peak Cap Assembly. Attach with two #8 x 3/4” Sheet Metal Screws per Ridge Cap Middle. (F30.9, F30.10 and F30.11) Ridge Cap Middle | arr Roof Assembly Large Roof Assembly Ridge Cap Middle Note: To help Ridge Caps slide on easier use a lubricant such as liquid soap.
Part 1 A: Insert one 1/4” Nut into each Peak Loop. Be careful nut is loose and will fall out until attached to Carriage Bolt. Only 2 are used in Part 1, the remaining 3 will be used in Part 2. (F31.1) Step 31: Secure Roof Peak Detail (A) B: Insert two Roof Peak Brackets through each end Carriage Bolt, so they fit over the Rafter Corners, and attach Peak Loop to Carriage Bolts then twist to tighten. (F31.2, F31.3 and F31.
Step 31: Secure Roof Peak Detail Part 2 D: Place one Peak Bracket over each of the remaining Carriage Bolts then attach Peak Loop to Carriage Bolts and twist to tighten. (F31.5 and F31.6) Components: 3 x Oak Bracket 70 supportgRyardistrystiuciurss.
Step 32: Attach Tie Wrap Brackets and Ties Part 1 =A) A: Attach one Tie Wrap Bracket tight F321 to each end of five (646) Ties with one #10 x Pan Screw per bracket using the inside holes. (F32.2 and F32.3) B: With a helper place one (646) Tie with brackets against each (633) Center Rafter on Large Roof Assemblies so (646) Tie is tight fo the rafters and are level. Attach Tie Wrap Bracket to (633) Center Rafters with two #10 x Pan Screws on both sides of each bracket. (F32.1, F32.2 and F32.
Step 32: Attach Tie Wrap Brackets and Ties =) (A) Part Attach one Double Tie Wrap Bracket RT and one Double Tie Wrap Bracket LT tight to each end of two (646) Ties with one #10 x Pan Screw per bracket using the inside holes. Make sure flat side of each bracket is on the same side of the (646) Ties. (F32.5, F32.6 and F32.7) E: With a helper place one (646) Tie against each (675) Middle Rafter on Comer Roof Assemblies so (646) Tie is tight to the rafters and are level.
Step 33: Attach Twist Brackets Q A: Measure (11.11 cm) down from the inside of each Post Assembly on the long side of the unit, place bottom of either 45° Twist Bracket LT or 45° Twist Bracket RT at measured location then attach to Post Assembly and Corner Rafter (Left or Right) with four #12 x Pan Screws per bracket. (F33.1 and F33.2) Rafter Comer (Left or Right) F33.2 45° Twist (LRT) #12x Pan Crow (11.
Step 34: Metal Hooks and Plaque % J A: Two 50 mm Hooks are included with this unit for attaching wiring. They can be placed anywhere along the Rafters as needed. Pr-drill with a 1/8" drill bit before installing. (F34.1 and F34.2) B: Attach Gazebo ID Plaque to a prominent location on your gazebo with two #8 x 1” Pan Screws. This provides warnings concerning safety and important contact information.
