Permanent Installation Examples Note: It is critically important you start with square, solid and level footings, concrete pad or deck to attach your Pergola Room. We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure to a per-existing or new wood or concrete surface. = The hardware to attach the Post Mount to the structure is included.
Permanent Installation Examples cont. Concrete Patio [min. 11° x 15’ (3.616 m x 4.836 m)] with 6” (15.24 cm) clearance on all sides Wood Deck [min. 11° x 15’ (3.616 m x 4.836 m)] with 6” {15.24 cm)clearance on all sides Post Mount Anchoring Hardware {not included) Post Mounts have a 1/2" (12.7 mm) diameter hole for anchoring hardware.
7 1 Dimensions are approximate and are shown to assist in the identification of parts for Part Identification ( assembly. Actual dimensions may be smaller or larger. Spe. (480) Plinth Long FSC 8pc. (459) Plinth FSC 23.6 x 133.4 x 276.2mm (15116 x 5% x 23.8 x 135.4 x 200mm (15/16 x 5% x : vs0229-460 TO | Y50229-459 4pc. (786) Straight Gusset Right FSC 38.1 x 130.7 x 1096.2mm 43-3116") & Y50220-786 Apc. (787) Straight Gusset Left FSC 38.1 x 139.7 x 1096.2mm / Y50229-787 2pc. (660) Left Beam Short FSC 38.
Part Identification on Dimensions are approximate and are shown to assist in the identification of parts for ) dimensions may be smaller or larger. 4pc. (624) Rafter Comer Left FSC 54 x 8839 x 2597.8mm 102%") = Romantic 4pc. (623) Rafter Corner Right FsC254 x 88.9 x 2587.8mm 10247) TL sozzled 2pc. (627) Fascia Left Short FSC 38.1 x 82.6 x 1855.5mm 73-1116") [.I” Yso220-827 ; : : 2pc. (628) Fascia Right Short FSC 38.1 x 82.6 x 1855.5mm 73-116") Ys0229-628 4pc. (629) Rafter Short RT FSC 31.8 x 76.2 x 805.
i 1 Dimensions are approximate and are shown to assist in the identification of parts for Part Identify cation assembly. actual Dimensions may be smaller or larger. ) 2pc. (639) Fascia Block FSC 38.1 x 50.8 x 368mm 1457) Co [vessels 2pc. (626) Fascia RT Long FSC 38.1 x 82.6 x 2465.5mm Y50229-626 2pc. (625) Fascia LT Long FSC 38.1 x 82.6 x 2465.5mm ¥s0229-625 2pe. (640) Strap Top Lg FSC 31.8 x 76.2 x 2179mm N\ Y50229-640 2pc. (642) Strap Mid RT FSC 31.8 x 76.2 x 2175.8mm (641) Strap Mid LT FSC 31.8 x 76.
T 7 Dimensions are approximate and are shown to assist in the identification of Hardware Dent cation ( parts for assembly. Actual dimensions may be smaller or larger. 4pc. Short Panel Left . Long Panel Right (Y01030-200) Ape (Y01030-197) a V 4pc. Middle Panel (Y01030-196) Ape. Roof Panel Set 4pc. Long Panel Left 4pc. Short Panel Right pe (Y01030-198) (Y70830-195) (Y01030-199) r 2pe. Roof Edge Left 72.2 (Y01030-134) r L 2pc. Roof Edge Right 72.2 (Y01030-135) t 7 8pe. Ridge Clip 102.5 (Y01030-133) 2pc.
Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of parts for assembly. Actual dimensions may be smaller or larger. 4pc. Roof Peak Bracket (Y00429-125) 3pe. 1/4" Nut ® Sprig Ci prong Clip (Y09490-001) (Y08490-200) 1pc. Roof Peak Set (Y70829-215) 3pc. Contour Washer {Y05918-211) 3pc. Peak Post (Y01000-094) 3pe. Carriage Bolt (Y07428-260) o 1pc. Peak Cap Assembly (Y70830-249) 1pe. Post Mount Set {ea (Y70828-122) > 1pe.
Step 1: Inventory Parts Read This Before Starting Assembly This is the time for you to inventory all your hardware, wood and accessories, referencing the parts identification sheets. This will assist you with your assembly. » Each step indicates which bolts and/or screws you will need for assembly, as well as any flat washers, lock washers, t-nuts or lock nuts. B. If there are any missing or damaged pieces or you need assistance with assembly please contact the consumer relations department directly.
Step 2: Post Assemblies A: At the bottom of one (621) 6 x 9 Post insert two 5/16” T-Nuts on the outside of each long side. (fig. 2.2) B: At the bottom of the same (621) 6 x 8 Post place two Post Mounts tight to the bottom and inside faces on the long sides as shown in fig. 2.1 and 2.2. Loosely attach with two 5/16 x Hex Bolt (with 5/16” lock washer and large washer) per mount so they connect to the T-Nuts. From the bottom attach with two #8 x Wood Screws and two #10 x Pan Screws per mount. Tighten bolts.
Step 3: Short Beam Assembly Part 1 A: Connect one (660) Left Beam Short and one (661) Right Beam Short using three 5/16 x Hex Bolts (with 5/16” lock washer, large washer and 5/16” t-nut) as shown in fig. 3.1 and 3.2. Notice orientation of bolt heads. B: Connect one (665) End Short Beam to each end of one (664) Center Beam Short using three 5/16 x Hex Bolts {with 5/16” lock washer, large washer and 5/16” t-nut) per end as shown in fig. 3.1 and 3.3. Notice orientation of bolt heads.
Step 3: Short Beam Assembly Part 2 D: Place one Short Beam L-R Assembly and one End Short Beam Assembly together so the beam assembly ends are flush and the angled ends match. Bolt heads must be on the outside of both beam assemblies. Match the bolt holes in each assembly then loosely attach with four 5/16 x 3" Hex Bolts (with 5/16” lock washer, 1/45/16" large washer and 5/16” t-nut) in the top holes. (fig. 3.4 and 3.5) E: Secure assemblies with 18 #8 x Wood Screws then tighten bolts. (fig. 3.
Step 4: Long Beam Assembly Part 1 A: Connect one (649) Outer End Right and one (650) Outer End Left using two 5/16 x Hex Bolts (with 5/16" lock washer, large washer and 5/16” t-nut) as shown in fig. 4.1 and 4.2. Notice orientation of bolt heads. B: Connect one (656) Inside Beam to each end of one (653) Inside Long Beam using two 5/16 x Hex Bolts {with 5/16" lock washer, large washer and 5/16" t-nut), in the middle holes, as shown in fig. 4.1 and 4.3. Notice orientation of bolt heads.
Step 4: Long Beam Assembly Part 2 D: Place one Long Beam Insert centered on the inside of one Inside Beam Assembly (t-nut side). Match the bolt holes in the Inside Beam Assembly and Long Beam Insert then attach with ten #7 x 3/4” Wood Screws. (fig. 4.4, 4.5 and 4.6) E: Repeat Step D for the second Inside Beam Assembly. Notice orientation ‘of angled ends Fig. 4.4 Inside Beam Assembly Long Beam Insert Fig. 4.
Step 4: Long Beam Assembly Part 3 F: Place one Outer Beam Assembly and one Inside Beam Assembly together so the beam assembly ends are flush and the angled ends match. Bolt heads must be on the outside of both beam assemblies. Match the bolt holes in each assembly then loosely attach with eleven 5/16 x 3” Hex Bolts (with 5/16" lock washer, large washer and 5/16” t-nut). The bolts at each end must go in the top holes. (fig. 4.7, 4.8, 4.9 and 4.
Step 5: Frame Assembly and Anchoring Q Part hard, flat surface place one Short Beam Assembly against the outside of two Post Assemblies, on the short side, flush to the tops and outside comers. Attach Beam to Post, through the middle hole, with one 3/8 x 121/2" Hex Bolt (with two 3/8” large washers and one 3/8” lock nut) per Post. (fig. 5.1 and 5.2) The distance from the outside of one Post Assembly to the outside of the second Post Assembly should be 10’ 103/8". See fig. 5.
Step 5: Frame Assembly and Anchoring Part 2 Note: The beveled ends on each gusset should always face away from the wood it Is attaching fo.
Step 5: Frame Assembly and Anchoring Part 3 F: Move your Short Side Assemblies to the final location. Make sure the ground is flat and level before continuing assembly. G: With helpers stand up Short Side Assemblies then place one Long Beam Assembly against the outside of two Post Assemblies, flush to the tops and outside corners and tight to Short Beam Assembly.
Step 5: Frame Assembly and Anchoring Part 4 Note: The beveled ends on each gusset should always face away from the wood it Is attaching to. H: Make sure the Frame Assembly is square and level then facing one Long Beam Assembly from the outside place one (786) Straight Gusset Right on the right hand side Post Assembly so the top fits tight to the Long Beam Assembly and the bottom fits tight to the Post Assembly.
Step 5: Frame Assembly and Anchoring Tu Part 5 L: Pr-drill with a 1/8” drill bit then attach Long Beam Assemblies to Post Assemblies with one 5/16 x Lag Screw (with large washer) per corner in the middle holes and Short Beam Assemblies fo Post Assemblies with two 5/16 x Lag Screws (with large washer) per comer in the top and bottom holes. (fig. 5.11) M: Depending on what you are placing the Gazebo on will determine how you anchor it to that surface. Please refer to pages 6 and 7 for installation examples.
Step 6: Fascia Beam Assembly Small Roof Assembly A: Tightly connect one (627) Fascia Left Short and one (628) Fascia Right Short using one 5/16 x Hex Bolt (with 5/16" lock washer, large washer and 5/16” t-nut) as shown in fig. 6.1 and 6.2. Repeat to make a second Fascia Beam Assembly. 516° Tone Tut 114-5018" Large Washer Fig. 6.
Step 7: Small Roof Assembly Part 1 A: On each side of one (634) Rafter place one (624) Rafter Comer Left and one (623) Rafter Comer Right so the tops and edges are flush then attach with two #8 x Wood Screws per side. (Fig. 7.1 and 7.2) B: Place Fascia Beam Assembly from Step 6 on the bottom of (634) Rafter Comer Left, (623) Rafter Comer Right and (634) Rafter so the sides are flush then attach with one #8 x Wood Screw at each end and one #8 x Wood Screw in the middle. (fig. 7.1, 7.3, 7.4 and 7.
Step 7: Small Roof Assembly Part 2 D: Place one (629) Rafter Short RT, one (632) Rafter Center RT, one (631) Rafter Center LT and one (630) Rafter Short LT over the pilot holes in the Fascia Beam Assembly so they are flush to the top of the assembly and tight to both (623) Rafter Comer Right and (634) Rafter Comer Left, as shown in fig. 7.6. Attach Fascia Beam Assembly to rafters with one #8 x Wood Screw per rafter. Repeat for second Small Roof Assembly. (fig. and 7.8) (624) Rafter Fig. 7.
Step 7: Small Roof Assembly Part 3 E: Place one (636) Top Strap, one (637) Mid Strap, one (687) Bottom Strap LT and one (688) Bottom Strap RT in the notches of each rafter so the ends do not overhang the outside edges of the outside boards. (687) Bottom Strap LT and (688) Bottom Strap RT sit tight together. Attach with four #8 x Wood Screws per strap. Complete for each Small Roof Assembly. (fig. 7.9, 7.10 and 7.11) (637) Mid Fig. 7.9 (serrate &n Coma Cad? PRS #8 x Wood Screws. Flg. 7.
Step 7: Small Roof Assembly Part 4 F: Attach (629) Rafter Short RT and (632) Rafter Center RT to (623) Rafter Comer Right and (631) Rafter Center LT and (630) Rafter Short LT to (624) Rafter Corner Left with two #8 x Wood Screw per rafter. (fig. 7.12 and 7.13) G: Attach (636) Top Strap, (637) Mid Strap and (687) Bottom Strap LT to rafters with 16 #8 x Wood Screws. (fig. 7.14) H: Complete Steps F and G for both Small Roof Assemblies. (623) Rafter ‘Comer Right (624) Rafter Fig. 7.
Step 8: Attach Officiants Small Roof Assembly A: Tum over each Small Roof Assembly then place two (648) Officiants tight together at center of (634) Rafter and tight to the top of Fascia Beam Assembly. Attach (648) Officiants to (634) Rafter, (623) Rafter Comer Right, (624) Rafter Corner Left, (629) Rafter Short RT, (630) Rafter Short LT, (632) Rafter Center RT and (631) Rafter Center LT with four #8 x 1” Pan Screws per offsite. (fig. 8.1 and 8.2} Fig. 8.
INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! HANDLE WITH CARE! Place roofing material on a non-abrasive surface before assembly as it can bend, dent and scratch easily. WARNING —DO NOT OVER TIGHTEN ROOFING SCREWS! Over tightening screws will cause roofing material to crush. Over tightened and Crushed Snug and Tight The roofing screws can easily crush the Roof Panels and Roof Edges when using a power drill.
INSTALLING ROOFING MATERIAL CAUTION! Roofing material may have sharp edges! Wear gloves! BE SURE TO REMOVE ALL PLASTIC COVERING, ON BOTH SIDES OF THE ALUMINUM PANELS AND TRIM, DIRECTLY BEFORE INSTALLING EACH PIECE. (One side is clear and the other is blue, both must be removed.
Step & Attach Roof Panels Small Roof Assembly al A: Place one Long Panel Left on the front of one Small Roof Assembly so it is flush to the side of (624) Rafter Comer Left and a slight overhang at the bottom of the Fascia Beam Assembly. Center holes should line up with (634) Rafter. (fig. 9.1 and 9.2) B: Place one Long Panel Right on Small Roof Assembly so it overlaps the Long Panel Left and it is flush to the side of (623) Rafter Comer Right and a slight overhang at the bottom of the Fascia Beam Assembly.
Attach Roof Panels Small Roof Assembly Step 9 Part 2 E: Place one Short Panel Left on Small Roof Assembly so it overlaps the Long Panel Left and it is flush to the sides of (624) Rafter Comer Left and a slight overhang at the bottom of the Fascia Beam Assembly. There (fig. 9.3 and 9.4) should be no overhang at the corners. the side of (623) Rafter Comer Right and a slight overhang at the bottom of the Fascia Beam Assembly.
Step 10: Attach Ridge Clips and Roof Edges Q Small Roof Assembly A: Place one Roof Edge Left 72.2 and ons Roof Edge Right 72.2 on the bottom of each Small Roof Assembly so the ends are flush with the outside ends of the Fascia Beam Assembly and meet tight in the center. Attach both Roof Edges with Roofing Screws per Small Roof Assembly. (fig. 10.1 and 10.2) B: Place one Weather Seal on the inside of four Ridge Clip 102.5 then place one Ridge Clip 102.
Step 11: Fascia Beam Assembly Large Roof Assembly A: Tightly connect one (625) Fascia LT Long and one (626) Fascia RT Long using one 5/16 x Hex Bolt {with 5/16” lock washer, large washer and 5/16” t-nut) as shown in fig. 11.1 and 11.2. Repeat to make a second Large Fascia Beam Assembly. Ei Tight Fig. 11.2 Fig. 11.
Step 12: Large Roof Assembly ] Part 1 A: Place one (635) Long Roof Top in between both (634) Rafters. (635) Long Roof Top to be flush to the tops to the ends of each (634) Rafter. Attach each (634) Rafter to (635) Long Roof Top with two #8 x Wood Screws per Rafter. (fig. 12.1) B: Measure (1.764 m) from the inside ends of the Large Fascia Beam Assembly then place one (634) Rafter aver each pilots hole, flush to the top of the Large Fascia Beam Assembly and attach with one #8 x Wood Screw per rafter. (fig.
Step 12: Large Roof Assembly Part 2 F: Place one (629) Rafter Short E: On the sides of Large Fascia Beam Assembly place one (624) Rafter Corner Left and one (623) Rafter Comer Right so the tops and edges are flush then attach to (634) Rafters with two #8 x Wood Screws per board and to Large Fascia Beam Assembly with one #8 x Wood Screw per board. (Fig. 12.3, 12.4 and 12.5) RT, one (632) Rafter Center Fig. 12.
Step 12: Large Roof Assembly Part 3 I: On only one Large Roof Assembly, place two (645) Spacers on (635) Long Roof Top. To find the correct placement of each spacer insert one 1/4 x Hex Bolt through (635) Long Roof Top into each (645) Spacer. The bolts are for placement only, they are to be removed at the end of this step. Attach each spacer to (635) Long Roof Top with two #8 x Wood Screws per spacer. Remove bolts, to be used in Step 18. (fig. 12.6) (645) Spacer Fig. 12.
Step 12: Large Roof Assembly Part 4 E: Place one (640) Strap Top LG, one (641) Strap Mid LT, one (642) Strap Mid RT, one (643) Strap Bot LT and one (644) Strap Bot RT in the notches of each rafter so the ends do not overhang the outside edges of the outside boards. (641) Strap Mid LT and (642) Strap Mid RT sit tight together and (643) Strap Bot LT and (644) Strap Bot RT sit tight together.
Step 12: Large Roof Assembly Part 5 F: Attach (629) Rafter Short RT and (632) Rafter Center RT to (623) Rafter Corner Right and (631) Rafter Center LT and (630) Rafter Short LT to (624) Rafter Comer Left with two #8 x Wood Screw per rafter. Complete for each Large Roof Assembly. (fig. 12.9 and 12.10) Fig.12.9 (820)Rater Cope Right Comer Left (631) Rafter 632) Rafter (630) Rafter Center LT (632) (629) Rater Short LT Center RT Short RT #8 x Wood Screws Fig. 12.
Step 12: Large Roof Assembly Part 6 G: Attach (640) Strap Top LG, (641) Strap Mid LT, (642) Strap Mid RT, (643) Strap Bot LT and (644) Strap Bot RT to (629) Rafter Short RT, (632) Rafter Center RT, (630) Rafter Short LT, (631) Rafter Center LT and both (633) Center Rafters with 24 #8 x Wood Screws. Complete for each Large Roof Assembly. (fig. 12.11 and 12.12) (640) Strap Top LG (842) Strap Mid Flg. 12.
Step 12: Large Roof Assembly Part 7 H: Turn over each Large Roof Assembly then place one (639) Fascia Block in between both (633) Center Rafters, flush to the front of the Large Fascia Beam Assembly. Attach (639) Fascia Block to Large Fascia Assembly with two #8 x Wood Screws. (fig. 12.13 and 12.14) I: Place two (647) Offsite Longs tight to the top Large Fascia Assembly so they meet tight together in the center and are flush with the outside edges of (623) Rafter Corner Right and (624) Rafter Comer Left.
Step 13: Attach Roof to Beam Brackets Large Roof Assembly Fig. 13.2 Back View Roof to Beam Bracket 1/4” Lock Fig. 13.1 MN Large Washer Hex Bolt Bracket | 1/4” Lack Nut A: On the back of each Large Roof Assembly, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to each (633) Center Rafter with one 1/4 x 2” Hex Bolt (with two large washers and one 1/4” lock nut) per bracket. (fig. 13.1 and 13.
Step 14: Attach Roof Panels Large Roof Assemblies Q Part 1 IMPORTANT!: Before starting this step, be sure to refer back to pages 32 & 33 regarding correct Installation and handling of the roofing. A: Tum over Large Roof Assemblies. Place two Middle Panels flush to the top of (635) Long Roof Top. On each side of the Middle Panels place one Long Panel Left and one Long Panel Right. There will be an overhang at the bottom over Large Fascia Assembly but no overhang at the Comer Rafters.
Step 14: Attach Roof Panels Large Roof Assemblies Part 2 C: Place one Short Panel Left so it overlaps Long Panel Left and is flush to the side of (624) Rafter Corner Left. Place one Short Panel Right so it overlaps Long Panel Right and is flush to the side of (623) Rafter Corner Right. There will be a slight overhang a the bottom of the Large Fascia Beam Assembly. There should not be any overhang at the comers. (fig. 14.4 and 14.
Step 15: Attach Roof Edges Large Roof Assemblies A: Place one Roof Edge Left 96.2 and one Roof Edge Right 96.2 on the bottom of sate Large Roof Assembly so the ends are flush with the outside ends of the Large Fascia Beam Assembly and meet tight in the center. Attach both Roof Edges with Roofing Screws per Large Roof Assembly. (fig. 15.1 and 15.2) Fig. 15.1 Top Tight at central #8x 1" Roofing Screws (x 23) Flg. 15.2 fa Roof Edge Right 96.
Step 16: Attach Ridge Clips Large Roof Assemblies Q@ A: Place one Weather Seal on the inside of four Ridge Clip 102.5 then place one Ridge Clip 102.5 on each side of each Large Roof Assembly so they cover the panels and are flush to the tops of (623) Rafter Corner Right and (624) Rafter Corner Left. The bottom edge of each Ridge Clip 102.5 should be (63.5 mm) up from the bottom edge of (623) Rafter Corner Right and (624) Rafter Comer Left. Attach with five #7 x 3/4” Wood Screws per Ridge Clip 102.5. (fig.
Step 17: Peak Cap Assembly 1 A: Insert three Carriage Bolts with Contoured Washers through the top of Peak Cap Assembly. Place one Peak Post over each Carriage Bolt and secure with Spring Clips. The Spring Clip holds the assembly together. (fig. 17.1 and 17.2) Ca raga Bolt Fig. 171 Clip Peak Cap Assembly Components; Hardware 1 x Peak Cap Assembly 3 x Carriage Bolt 3 x Contoured Washer 3 x Peak Post 3 x Spring Clip 50 supportgRyardistrystiuciurss.
Step 18: Attach Large Roof Assemblies to Frame art A: With all five assemblers lift Large Roof Assembly with (645) Spacers centered on the Long Beam Assembly. With an assembler holding the first Large Roof Assembly in place lift the second Large Roof Assembly on the opposite Long Beam Assembly. Loosely attach Large Roof Assemblies at the top with two 1/4 x Hex Bolts (with two large washers and one 1/4” lock nut). The bottom of the Rafter Corners should be aligned with the miter of the Beam Assemblies (fig.
Step 18: Attach Large Roof Assemblies to Frame (AEH) Part 2 B: From the outside of the assembly have one person push one Large Roof Assembly in so (648) Offsite fits tight to the Long Beam Assembly and two people pushing up at the peak. One person fastens each Roof to Beam Bracket to (633) Center Rafters then to the Long Beam Assemblies with three #12 x Pan Screws. Install top screw into (633) Center Rafter first then other two into the beam. Tighten bracket bolts.
Step 18: Attach Large Roof Assemblies to Frame (AEH) Part 3 C: Attach one Roof to Beam Bracket to each (634) Rafter on both Large Roof Assemblies with one 1/4 x 2” Hex Bolt (with two large washers and one 1/4” lock nut) and three #12 x Pan Screws, per bracket. (fig. 18.5 and 18.6) D: Tighten both bolts which join Large Roof Assemblies. (fig. 18.
Step 18: Attach Large Roof Assemblies to Frame Part 4 E: With one person on each end of the roof place Peak Cap Assembly on top of Large Roof Assemblies so Carriage bolts with Peak Post fit through gaps between the roof assemblies. (fig. 18.8) F: Insert one 1/4” Nut into one Peak Loop. Be careful nut is loose and will fall out until attached to Carriage Bolt. (fig. 18.9) G: Place one Peak Bracket over the middle Carriage Bolt then attach Peak Loop to Carriage Bolt and twist to tighten. (fig. 18.10) Fig. 18.
Step 19: Attach Small Roof Assemblies to Frame (8) A: With all four assemblers lift one Small Roof Assembly up and over the Short Beam Assembly. You will need to lift the Roof Peak Assembly to get the top under it. Loosely attach each (623) Rafter Comer Right to each (624) Rafter Comer Left with three 1/4 x Hex Bolts (with two large washers and one 1/4” lock nut) per side. To align bolt holes helper in the center may have to push up the center of the panels and others make sure comers are aligned.
Step 20: Secure Roof Corners 1 A: From outside the assembly attach Small Roof Assemblies and Large Roof Assemblies together at the Fascia Beam Assembly and Large Fascia Beam Assembly with two #8 x Wood Screws per corner. A helper may need to lift the center of the roof to bring the comers tight together. (fig. 20.
Step 21: Attach Roof to Beam Brackets Small Roof Assembly A: On each Small Roof Assembly, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to each rafter with one 1/4 x 2” Hex Bolt (with two large washers and oneness” lock nut) per bracket. (fig. 21.1 and 21.2) B: Push panels up from the outside and inside top to make sure each (648) Offsite is tight to the Short Beam Assemblies then fasten each Roof to Beam Bracket with three #12 x Pan Screws per bracket.
Step 22: Attach Roof to Beam Brackets Large Roof Assembly A: On both Large Roof Assemblies, through the bolt hole at the bottom of the board, loosely attach one Roof to Beam Bracket to each (629) Rafter Short RT, (630) Rafter Short LT, (631) Rafter Center LT and (632) Rafter Center RT with one 1/4 x 2° Hex Bolt (with two large washers and one 1/4" lock nut) and three #12 x Pan Screws per bracket. Install top screw into the rafter first then install the other two into the beam. (fig. 22.1 and 22.
Step 23: Attach Ridge Caps to Roof Panels each comer, slide one Ridge Cap Long 81.5 over the Ridge Clips, from the bottom up with cut end leading. (fig. 23.1 and 23.2) B: Slide Ridge Cap Short 25.2 over the Ridge Clips leading with the insert end to push the Ridge Cap Long 81.5 to the top, lifting Peak Cap Assembly so Ridge Cap Long 81.5 fit under. Attach with two #8 x 3/4” Sheet Metal Screws per Ridge Cap set. (fig. 23.1, 23.3, 23.4 and 23.5) Ridge Clip, 1025 Ridge Cap Long 81.
Step 24: Secure Roof Peak Detail (A) A: Insert one 1/4” Nut into two Peak Loops. Be careful nut is loose and will fall out until attached to Carriage Bolt. (fig. 24.1) B: Insert two Roof Peak Brackets through each end Carriage Bolt, so they fit over the Rafter Corners, and attach Peak Loops to Carriage Bolts then twist to tighten. (fig. 24.2, 24.3 and 24.
Step 25: Attach Tie Wrap Brackets and Ties =A) A: Attach one Tie Wrap Bracket tight (645) Tie to each end of four (646) Ties with one Fig. 25.1 #10 x Pan Screw per bracket using the inside holes. (fig. 25.2 and 25.3) B: With a helper place one (646) Tie with brackets against each (633) Center Rafter and each (634) Rafter on Large Roof Assemblies so (646) Tie is tight to the rafters and are level. Attach Tie Wrap Bracket to Rafters with two #10 x Pan Screws on both sides of each bracket. (fig. 25.1, 25.
Step 26: Attach Twist Brackets Q A: Measure 4” down from the inside of each Post Assembly, place bottom of either 45° Twist Bracket LT or 45° Twist Bracket RT at measured location then attach to Post Assembly and Comer Rafter (Left or Right) with four #12 x Pan Screws per bracket. (fig. 26.1 and 26.2) Fig. 26.2 —~ #M2x 1112 He Pan Screw Rafter Comer (Left or Right) 45° Twist Bracket : ATR) Pan Screw Components: Hardware 2 x 45° Twist Bracket Pan Craw 2 x 45° Twist Bracket RT 82 supportgRyardistrystiuciurss.
Step 27: Metal Hooks and Plaque % J A: Two 50 mm Hooks are included with this unit for attaching wiring. They can be placed anywhere along the Rafters as needed. Pr-drill with a 1/8" drill bit before installing. (fig. 27.1 and 27.2) B: Attach Gazebo ID Plaque to a prominent location on your gazebo with two #10 x Pan Screws. This provides warnings concerning safety and important contact information.
