6574 STOP! Call Us First! DO NOT RETURN TO STORE. For immediate help with assembly or product information call our toll free number: 1-800-844-9273 or email: customerservice@yardline.
(This page intentionally left blank.
16574 05/09/2016 A Backyard Products Company CRESTWOOD GABLE 8' x 14' (244 x 426,7 cm) ACTUAL FLOOR SIZE IS 96 x 168" (243,8 x 426,7 cm) KEEP THIS MANUAL FOR FUTURE REFERENCE OPTION 1: DOOR LOCATION LEFT SIDE OF FRONT WALL OPTION 2: DOOR LOCATION RIGHT SIDE OF FRONT WALL I M P O RTA NT! READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.
TOOLS Required ❑ Phillips Optional ❑ Tool Belt/ ❑ Utility Knife Screwdriver Nail Pouch ❑ Shingle Blades ❑ Drill / Driver ❑ 1/8" Drill Bit ❑ 1/4" Drill Bit ❑ 5/16" Drill Bit ❑ 1/2" Drill Bit ❑ #2 Philips Drive Bit ❑ Caulk Gun ❑ Tin Snips (for drip edge) ❑ Paint Tools ❑ Chalk Line ❑ Safety Glasses ❑ Hammer ❑ Nail Gun ❑ Level • gun nails ❑ Hand Saw ❑ Pencil ❑ Ladder ❑ Tape Measure ❑ Square ❑ Gloves or Safety! Always use approved safety glasses during assembly.
PARTS IDENTIFICATION AND SIZES Part identification letters are stamped on some parts. WOOD SIZE CONVERSION CHART Nominal Board Size Actual Size 2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm) RS 1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm) RS 2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm) Check these locations for part stamp. 1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm) PARTS LIST WALLS INVENTORY YOUR PARTS before you begin.
WINDOW TRIM, DOOR TRIM & SHUTTERS x3 JTA 19/32 x 6-7/16 x 2" (1,5 x 16,4 x 5,1 cm) x3 NRA 19/32 x 6-7/16 x 5-1/2" (1,5 x 16,4 x 14 cm) x4 DJA x1 AZ x4 DHA x1 DDA x1 AUA x1 DEA x3 OO 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) x2 LRA 1 x 4 x 69-3/4" (2,5 x 10,2 x 177,2 cm) x1 DGR 19/32 x 2-1/2 x 70-7/8" (1,5 x 6,3 x 180 cm) x2 DGL 19/32 x 2-1/2 x 70-7/8" (1,5 x 6,3 x 180 cm) x1 DFA 19/32 x 3-1/2 x 72" (1,5 x 8,9 x 182,9 cm) x1 ZJ 19/32 x 2-1/2 x 11" (1,5 x 6,3 x 27,9 cm) 19/
WALL PANELS & DOORS NOTE: Panel parts are not stamped.
FLOOR PARTS Floor panels are 5/8" (1,6 cm) thick. x2 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) x12 x2 NOTE: Panel parts are not stamped. Look for TREATED Stamp 2 x 4 x 93" (5,1 x 10,2 x 236,2 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) x3 x1 5/8 x 48 x 96" (1,5 x 121,9 x 243,8 cm) 5/8 x 23-7/8 x 96" (1,5 x 60,6 x 243,8 cm) ROOF PANELS Roof panels are 7/16" (1,1 cm) thick. NOTE: Panel parts are not stamped.
FASTENERS & HARDWARE FASTENER/HARDWARE BAG x130 x335 x113 x30 x27 x100 x25 x7 Boxes x4 Boxes 1-1/2" (3,8 cm) 2" (5,1 cm) 3" (7,6 cm) 2" (5,0 cm) 1-5/8" (4,1 cm) 3/4" (1,9 cm) 1" (2,5 cm) 2" (5,1 cm) 3" (7,6 cm) VENT/ DOOR HARDWARE/ WINDOWS Window 22-1/4 x 29-3/4" (56,5 x 75,6 cm) T-Handle x2 x2 x1 x2 Spring Bolt 4-1/2" Shaft x1 5-1/2" Shaft x8 x4 1-1/2" (3,8 cm) (2 screws in each package) Vent with Frame Decorative Hinges x6 x2 x18 1" (2,5 cm) 7 1" (2,5 cm) (4 screws in each package)
ADDITIONAL MATERIALS FOUNDATION OR FLOOR MATERIALS • This shed does not include any leveling materials. • See the FLOOR LEVELING section on page 9 for recommended methods and suggested materials to properly level your floor, as this will vary depending on your specific site. • If you choose to install your kit on a concrete slab refer to page 10.
OPTIONAL WOOD FRAME FLOOR LEVELING OPTIONS There are multiple ways to level your floor frame. Our recommended leveling method is shown below. Leveling materials are not included in this kit. PREFERRED METHOD - 4x4 TREATED RUNNERS (Typical for 8' x 14' Kit) Runners are generally 12" (30,5 cm) from ends of floor frame and under seams. Measurements to centers of 4x4's. • 3" Screws angled into 4x4. • (2) at each point frame and 4x4 touch.
CONCRETE FOUNDATION Your kit contains all materials to construct a wooden floor. If you choose to install your kit on a concrete slab refer to the diagram below. Treated Sill Plate Caulk between sill plate and concrete. C B 3-1/2" (8,9 cm) E GL S I NO O R D A E D O U DB LO O R 4" (10,2 cm) Building Size Actual Size 8' x 14' (243,8 x 365,8 cm) 96" x 168" (243,8 x 426,7 cm) A B 96" (243,8 cm) 161" (408,9 cm) Requires: x2 2" x 4" x 14' (5,1 x 10,2 x 365,8 cm) MUST be treated lumber.
FLOOR FRAME PARTS REQUIRED: x12 x2 x2 x44 3" (7,6 cm) Look for 2 x 4 x 93" (5,1 x 10,2 x 236,2 cm) TREATED Stamp 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) BEGIN 1 Orient parts as shown on flat surface. Measure and mark. HINT: For easier nailing stand on frame. Use two 3" nails at each mark. FINISH You have finished your floor frame. Proceed to level and square frame.
LEVEL AND SQUARE FLOOR FRAME Before attaching floor decking, it is important to level and square the floor frame. A level and square floor frame is required to correctly construct your shed. BEGIN 1 2 See page 9 for the preferred floor leveling method. Use level and check the frame is level before applying floor panels. Check for frame squareness by measuring diagonally across corners. If the measurements are the same, the frame is square.
FLOOR PANELS PARTS REQUIRED: x219 2" (5,1 cm) 5/8 x 48 x 96" (1,6 x 121,9 x 243,8 cm) x1 Ensure your floor frame is square by installing one panel and squaring frame. BEGIN 1 2 Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with the 48" edge and corner flush to the floor frame (Fig A). Secure panel with two 2" nails in the corners. (2) Nails Move to the opposite side.
FLOOR PANELS PARTS REQUIRED: 2" (5,1 cm) x1 5/8" x 23-7/8" x 96" (1,6 x 60,6 x 243,8 cm) x2 5/8" x 48" x 96" (1,6 x 121,9 x 243,8 cm) 4 Continue installing panels with rough side up (painted grid lines). Use a chalk line or use pre-painted grid lines on panel for 2" nails 6" apart on edges, and 12" apart inside panels. Flush 48" (121,9 cm) 23-7/8" (60,6 cm) 48" (121,9 cm) 6" (15,2 cm) 12" (30,5 cm) Grid lines up Flush Flush Flush Flush FINISH You have finished attaching your floor panels.
IMPORTANT! DO U DO BLE OR Check the floor frame is level after installing floor panels. Re-level if needed. SIN D O O RG L E • The floor should be used as a stable work surface for wall construction. HINT: • Organize your assembly procedure during the build process to avoid over-handling of the walls. GABLE END WALL BACK WALL BACK WALL FRONT WALL GABLE DOOR WALL (Your door location may vary.
RAFTER ASSEMBLY PARTS REQUIRED: x3 CPA x6 3" (7,6 cm) 2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm) You will build a rafter jig using the floor and three CPA parts as shown. ¸1 BEGIN 2 Secure one CPA flush to the floor deck using two 3" screws. Measure over 96-3/4" and install a second CPA flush to the floor deck. CPA will overhang the floor. Secure using two 3" screws. Measure over 48" and up 35-3/16" from the floor edges and secure CPA using two 3" screws.
RAFTER ASSEMBLY PARTS REQUIRED: x14 x16 OSB OR WOOD GRAIN x 16 x 168 1-5/8" (4,1 cm) 2" (5,1 cm) 6 x 24" (15,2 x 61 cm) ASA 2 x 4 x 63-7/8" (5,1 x 10,2 x 162,2 cm) You will build 8 rafters - Six with 2 gussets and Two with only 1 gusset. ¸1 BEGIN Place two rafters ASA into the jig as shown. Keep ASA firm against outside CPA's as shown (Fig.A) and push rafters tight to the middle CPA. Rafters should touch at tips (Fig. A). Apply glue to rafters where gusset will attach (Fig. B).
GABLE DOOR WALL PARTS REQUIRED: 2 x 4 x 10" (5,1 x 10,2 x 25,4 cm) x2 x1 x24 x2 AJ x3 PWA 3" (7,6 cm) 2 x 4 x 12-1/2" (5,1 x 10,2 x 31,8 cm) x1 TK 2 x 4 x 80" (5 x 10,2 x 203,2 cm) UX 2 x 4 x 64" (5,1 x 10,2 x 162,6 cm) SZ 2 x 4 x 89" (5 x 10,2 x 226,1 cm) BEGIN 1 Orient parts on edge on floor. Measure and mark. HINT: For easier nailing stand on frame. Use two 3" nails at each mark.
GABLE DOOR WALL PARTS REQUIRED: x1 x2 OO 3" (7,6 cm) Temporary support x52 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) 48 x 84" (121,9 x 213,4 cm) x1 LEFT + 1 RIGHT 2 2" (5,1 cm) Place left 48" x 84" panel onto wall frame flush to top of SZ with primed side up as shown. Secure panel with 2" nails 6" (15,2 cm) apart. Repeat Step 2 to attach the right 48" x 84" panel. SZ 3-1/2" (8,9 cm) For squareness maintain flush along panel edges.
STOP AS YOU FACE THE FRONT WALL, CHOOSE YOUR SINGLE DOOR LOCATION LEFT OR RIGHT IMPORTANT: The single door is a reversible door and can either be left hand swing or right hand swing, depending on your preference. FRONT WALL GABLE WALL DOUBLE DOORS If you choose to install your single door on the right hand side of the shed and with a right hand swing, note the double doors and the single door will bump and interfere with each other if opened at the same time. Please be aware of this issue.
FRONT WALL WITH DOOR LEFT PARTS REQUIRED: x4 x4 x16 AO 3" (7,6 cm) 2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm) TK 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm) You will build two window frame assemblies (Fig.A). HINT: For easier nailing stand on frame. BEGIN 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark. 22-1/2" (57,1 cm) 3" (7,6 cm) Nails Fig. A AO 80" (203,2 cm) 70" (177,8 cm) TK 40" (101,6 cm) 1-1/2" (3,8 cm) 2 Repeat Step 1 to build second window frame.
FRONT WALL WITH DOOR LEFT PARTS REQUIRED: x1 x1 x7 x2 x2 QT 2 x 4 x 35" (5,1 x 10,2 x 88,9 cm) x42 ABA 3" (7,6 cm) 2 x 4 x 20" (5,1 x 10,2 x 50,8 cm) TM x2 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) TK CPA 2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm) 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm) TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) HINT: For easier nailing stand on frame. BEGIN 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark and four 3" nails at seams.
FRONT WALL WITH DOOR LEFT PARTS REQUIRED: x2 x1 x2 x2 x60 CPA 3" (7,6 cm) 2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm) QT 2 x 4 x 35" (5,1 x 10,2 x 88,9 cm) YFA 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) TK x2 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm) Window Frame Assembly 2 Place Sub-Assembly in frame as shown. Measure and mark. Use two 3" nails at each mark and four 3" nails at seam. 3 Orient door frame parts on edge on floor as shown. Measure and mark. Install QT first.
FRONT WALL WITH DOOR LEFT PARTS REQUIRED: x63 GAA 3/8 x 48 x 84" (1 x 121,9 x 213,4 cm) x1 3/4" GAUGE BLOCK BEGIN 1 2" (5,1 cm) Place 48" x 84" window panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with 2" nails 6" apart on edges and 12" apart inside panel. BEGIN HERE For squareness maintain Flush at top of panel and 3/4" measurement along panel edge.
FRONT WALL WITH DOOR LEFT PARTS REQUIRED: x66 2" (5,1 cm) GAA x1 2 3/8 x 48 x 84" (1 x 121,9 x 213,4 cm) 3/4" GAUGE BLOCK Place 48 x 84" single door panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with 2" nails 6" apart on edges For squareness maintain flush and 3/4" measurement along panel edge.
FRONT WALL WITH DOOR LEFT PARTS REQUIRED: x2 x1 x2 ATA Temporary Support 2 x 4 x 64-1/8" (5,1 x 10,2 x 162,9 cm) 3" (7,6 cm) x127 3/8 x 11-7/8 x 84" (1 x 30,2 x 213,4 cm) 2" (5,1 cm) 3/8 x 48 x 84" (1 x 121,9 x 213,4 cm) x1 3 Place 2nd 48" x 84" window panel primed side up onto wall frame, flush to top of frame and flush to installed panel. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with 2" nails 6" apart on edges and 12" apart inside panel.
FRONT WALL WITH DOOR RIGHT PARTS REQUIRED: x4 x4 x16 AO 3" (7,6 cm) 2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm) TK 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm) You will build two window frame assemblies (Fig.A). HINT: For easier nailing stand on frame. BEGIN 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark. 22-1/2" (57,1 cm) 3" (7,6 cm) Nails Fig. A AO 80" (203,2 cm) 70" (177,8 cm) TK 40" (101,6 cm) 1-1/2" (3,8 cm) 2 Repeat Step 1 to build second window frame.
FRONT WALL WITH DOOR RIGHT PARTS REQUIRED: x1 x1 x7 x2 x2 QT 2 x 4 x 35" (5,1 x 10,2 x 88,9 cm) x42 ABA 3" (7,6 cm) 2 x 4 x 20" (5,1 x 10,2 x 50,8 cm) TM x2 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) TK CPA 2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm) 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm) TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) HINT: For easier nailing stand on frame. BEGIN 1 Orient parts on edge on floor. Measure and mark. Use two 3" nails at each mark and four 3" nails at seams.
FRONT WALL WITH DOOR RIGHT PARTS REQUIRED: x2 x1 x2 x2 x60 CPA 2 x 4 x 8-1/2" (5,1 x 10,2 x 21,6 cm) 3" (7,6 cm) QT 2 x 4 x 35" (5,1 x 10,2 x 88,9 cm) YFA 2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm) TK x2 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm) Window Frame Assembly 2 Place Sub-Assembly in frame as shown. Measure and mark. Use two 3" nails at each mark and four 3" nails at seam. 3 Orient parts on edge on floor as shown. Measure and mark. Install QT first. Use two 3" nails at each mark as shown.
FRONT WALL WITH DOOR RIGHT PARTS REQUIRED: x63 GAA 3/4" GAUGE BLOCK 3/8 x 48 x 84" (1 x 121,9 x 213,4 cm) x1 2" (5,1 cm) BEGIN 1 Place 48" x 84" window panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with 2" nails 6" apart on edges and 12" apart inside panel. BEGIN HERE Primed side up Flush 3/4" (1,9 cm) For squareness maintain Flush at top of panel and 3/4" measurement along panel edge.
FRONT WALL WITH DOOR RIGHT PARTS REQUIRED: x66 2" (5,1 cm) GAA x1 2 3/8 x 48 x 84" (1 x 121,9 x 213,4 cm) 3/4" GAUGE BLOCK Place 48 x 84" single door panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with 2" nails 6" apart on edges For squareness maintain flush and 3/4" measurement along panel edge.
EAVE SIDE WALL WITH DOOR RIGHT PARTS REQUIRED: x2 x127 2" (5,1 cm) 3/8 x 11-7/8 x 84" (1 x 30,2 x 213,4 cm) x1 ATA Temporary Support 2 x 4 x 64-1/8" (5,1 x 10,2 x 162,9 cm) 3/8 x 48 x 84" (1 x 121,9 x 213,4 cm) x1 3 Place 2nd 48" x 84" window panel primed side up onto wall frame, flush to top of frame and flush to installed panel. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with 2" nails 6" apart on edges and 12" apart inside panel.
BACK WALL PARTS REQUIRED: x2 x8 x2 x36 3" (7,6 cm) 2 x 4 x 72" (5,1 x 10,2 x 182,9 cm) TM TK TP 2 x 4 x 80" (5,1 x 10,2 x 203,2 cm) 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) HINT: For easier nailing stand on frame. BEGIN 1 Orient parts on edge on floor. Measure and mark.
BACK WALL PARTS REQUIRED: x50 2" (5,1 cm) GAA x1 3/4" GAUGE BLOCK 48 x 84" (121,9 x 213,4 cm) Ensure your wall frame is square by installing one panel and squaring frame. 2 Place 1st 48 x 84" panel onto wall frame flush to top of frame with primed side up as shown. Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with two 2" nails in the corners (Fig. A). 3 Move to the opposite end.
BACK WALL PARTS REQUIRED: x2 2" (5,1 cm) GAA x1 48 x 84" (121,9 x 213,4 cm) 4 x136 3/4" GAUGE BLOCK 23-7/8 x 84" (60,6 x 213,4 cm) Place 2nd 48" x 84" panel on frame as shown with primed side facing up. For squareness maintain flush and 3/4" measurement along panel edges. Nail using 2" nails 6" apart on edges and 12" apart inside panel. Flush Primed side up 12" (30,5 cm) Flush 6" (15,2 cm) 48" (121,9 cm) 5 Place 3rd 48" x 84" panel on frame as shown with primed side facing up.
GABLE END WALL PARTS REQUIRED: x1 x2 x4 TK 3" (7,6 cm) 2 x 4 x 80" (5 x 10,2 x 203,2 cm) SZ 2 x 4 x 89" (5 x 10,2 x 226,1 cm) x2 x2 PVA Temporary support Temporary support DHA 19/32 x 5-1/2 x 30-1/8" (1,5 x 14 x 76,5 cm) 2 x 4 x 6" (5,1 x 10,2 x 15,2 cm) BEGIN 1 Orient parts on floor. TK is on flat side (Fig.A). Support center stud TK with temporary supports DHA and PVA as shown. Measure, mark and square. Use two 3" nails at each connection.
GABLE END WALL PARTS REQUIRED: x13 x16 1-1/2" (3,8 cm) 2" (5,1 cm) x1 48 x 84" (121,9 x 213,4 cm) 2 Place 48 x 84" panel with primed side up onto frame flush at top and with a 1-3/4" gap along right side. Maintain 1-3/4" measurement along edge. Secure panel to top and bottom plate using 2" nails 6" (15,2 cm) apart along edges. Secure panel to TK with 1-1/2" nails.
GABLE END WALL PARTS REQUIRED: 1-1/2" (3,8 cm) x16 2" (5,1 cm) 48 x 84" (121,9 x 213,4 cm) x1 3 x13 Place right 48 x 84" panel flush to left panel with primed side up. 2" (5,1 cm) Nails Secure using 2" nails 6" apart on edges. Flush 3-1/2" (8,9 cm) Primed side up 1-1/2" (3,8 cm) Nails 6" (15,2 cm) Flush 3-1/2" (8,9 cm) 48" (121,9 cm) 2" (5,1 cm) Nails 4 Carefully flip the gable wall over. Remove temporary supports. FINISH You have finished building your gable end wall.
FRONT WALL PARTS REQUIRED x1 OO x18 Temporary Support 3" (7,6 cm) x2 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) x28 3" (7,6 cm) 2" (5,1 cm) BEGIN Stand front wall on floor. 1 Center wall on the 168" (426,7 cm) floor dimension. (42 168 6,7 " cm ) Use OO as a temporary brace. Secure with two 3" screws. 3" (7,6 cm) Screws OO DOOR LOCATION MAY VARY 2 First, nail lower edge of panel to floor frame using 2" nails 6" apart. Angle nail to hit floor frame (Fig. A).
GABLE END WALL PARTS REQUIRED: x18 x14 x1 1-1/2" (3,8 cm) 3" (7,6 cm) 2" (5,1 cm) x6 3" (7,6 cm) x2 2" (5,1 cm) BEGIN 2" (3,8 cm) Screw Flush Stand wall on floor. It is important to secure the gable end wall in the following order: Flush Fig. A 2" (5,1 cm) Screw Set gable end wall on floor and secure top of wall using one 2" screw into top plate (Fig A). 1 STEP 1 FIRST SCREW ENSURE TOP OF WALL FRAMES ARE FLUSH.
BACK WALL PARTS REQUIRED: x2 x1 2" (5,1 cm) x14 3" (7,6 cm) 1-1/2" (3,8 cm) BEGIN Stand back wall on floor. 1 Center back wall on the 168" (426,7 cm) floor dimension. (42 168 6,7 " cm ) Secure top of wall using one 2" screw into top plate (Fig A). BE SURE TOP OF WALL FRAMES ARE FLUSH. 3" (7,6 cm) Screw Fig. C STEP 3 FIRST SCREW 2 Move to the bottom of gable end wall and secure bottom of wall using one 2" screw into back wall bottom plate (Fig A).
BACK WALL PARTS REQUIRED: x14 x30 3 3" (7,6 cm) 2" (5,1 cm) Nail lower edge of back wall panels to floor frame using 2" nails 6" apart. Angle nail to hit floor frame (Fig. D). Secure back wall bottom plates to floor using 3" nails (Fig. D). Remove temporary supports. 3" (7,6 cm) Nails 6" (15,2 cm) Nail 2" nails first. 3" (7,6 cm) Nails 2" (5,1 cm) Nails Fig. D FINISH You have finished standing your back wall.
GABLE DOOR WALL PARTS REQUIRED: x8 x2 x4 2" (5,1 cm) x4 3" (7,6 cm) x28 3" (7,6 cm) 2" (5,1 cm) 1-1/2" (3,8 cm) BEGIN Stand gable door wall on floor. It is important to secure the front wall in the following order: 1 Set gable door wall on floor and secure using one 2" screw (Fig A). ENSURE TOP WALL FRAMES ARE FLUSH. Flush 2" (5,1 cm) Screw Flush Fig. A Flush Flush 2" (5,1 cm) Screw 2" (5,1 cm) Screw Flush Fig.
GABLE DOOR WALL PARTS REQUIRED: 3 Nail lower edge of panels to floor using 2" nails 6" apart. Angle nail to hit floor frame (Fig. C). 2" (5,1 cm) Nails 6" (15,2 cm) Angle nail to hit floor frame. 6" (15,2 cm) Fig. C 3" (7,6 cm) Screw Fig. F 4 Fig. E Nail gable wall panels to front and back wall studs using 1-1/2" nails 6" apart (Fig. E). 6" (15,2 cm) Secure gable wall to floor using 3" nails (Fig. E).
GABLE UNITS PARTS REQUIRED: x2 PVA 2 x 4 x 6" (5,1 x 10,2 x 15,2 cm) x2 PWA x2 x16 2 x 4 x 10" (5,1 x 10,2 x 25,4 cm) x2 TEMPORARY SUPPORT AO x2 2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm) BEGIN 1 Orient parts on flat as shown. You will build TWO assemblies. Place LEFT front gable panel as shown and secure using 1-1/2" nails as shown.
GABLE UNITS PARTS REQUIRED: x4 x40 3" (7,6 cm) 2" (5,1 cm) x2 Gable Units BEGIN 1 Install both gable units the same on both gable walls. Measure 2-9/16" down from top plate and mark at each side as shown (Fig A). Set gable unit on top plate SZ. BE SURE GABLE UNIT IS CENTERED ON WALL BEFORE NAILING. 2 First, hold gable unit secure with one 2" nail on each side, then secure with two 2" nails at top of gable panels into end rafter (Fig. A).
LOFT PARTS REQUIRED: x8 x1 PT 3" (7,6 cm) x2 2 x 3 x 96" (5,1 x 7,6 x 243,8 cm) 3" (7,6 cm) x1 TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) If your front wall has door to LEFT side, see Fig. A. If your front wall has door to RIGHT side, see next page. BEGIN 1 Measure and mark gable wall corner studs 1/2" down from top plates (Fig. A). Place and hold top of PT on 1/2" marks. Secure PT with (6) 3" nails. 2 Measure and mark back wall 2nd stud and over-door crippler 1/2" down from top plates (Fig. A).
LOFT PARTS REQUIRED: x8 x1 PT 3" (7,6 cm) x2 2 x 3 x 96" (5,1 x 7,6 x 243,8 cm) 3" (7,6 cm) x1 TP 2 x 4 x 96" (5,1 x 10,2 x 243,8 cm) BEGIN 1 Measure and mark gable wall corner studs 1/2" down from top plates (Fig. B). Place and hold top of PT on 1/2" marks. Secure PT with (6) 3" nails. 2 Measure and mark TP 1/2" down from top plates at back wall 2nd stud. Measure and mark TP 1/2" down from top plates at front wall 3rd stud. Place and hold top of TP on 1/2" marks. Secure TP with 3" nails.
LOFT PARTS REQUIRED: x1 3 x7 7/16 x 26-5/8 x 89" (1,1 x 67,6 x 226,1 cm) Place 7/16" x 26-5/8" x 89" loft panel centered on loft supports. Slide panel into gap at gable wall (Fig. D). Secure to loft frame using 2" nails evenly spaced. Fig. D Gap FIT LOFT PANEL INTO 1/2" GAP ly ate roxim p p A 15" cm) 8 (3 ,1 Fig. C 7/16 -5/8 x 26 " x 89 ATTENTION: 2" (5,1 cm) Nails LOAD NOT TO EXEED 250 lbs (113,4 kg) EVENLY DISTRIBUTED ACROSS LOFT FINISH You have finished installing your loft.
SHELVES PARTS REQUIRED: x2 AED 2 x 3 x 21-3/4" (5,1 x 7,6 x 55,2 cm) x10 x4 3" (7,6 cm) 3" (7,6 cm) x2 PT 2 x 3 x 96" (5,1 x 7,6 x 243,8 cm) BEGIN 1 Measure and mark location for AED (Fig. A, Fig. B). Place loft support ledger boards AED between gable wall and eave wall stud with narrow side to wall panel (Fig. A). Secure each AED using (2) 3" screws toe-screwed at an angle at gable wall stud and 3" nails into eave wall stud as shown. 3" (7,6 cm) Nails Fig. A Fig.
SHELVES PARTS REQUIRED: x2 x8 3" (7,6 cm) x36 7/16 x 10-1/2 x 89" (1,1 x 26,7 x 226,1 cm) 2" (5 cm) x2 PT 2 x 3 x 96" (5,1 x 7,6 x 243,8 cm) 3 Measure and mark both AED's at the measurements shown from gable wall studs. Mark front wall stud at the dimensions shown Secure PT's using 3" screws at locations shown.
RAFTERS PARTS REQUIRED: x6 x28 Pre-Assembled Rafter with 2 gussets ¸1 3" (7,6 cm) x2 Pre-Assembled Rafter with 1 gusset BEGIN Locate first 2 gusset rafter on top plate, aligned over studs at each side and tight to side wall (Fig. A, Fig. B). Secure rafter to top plate with two 3" screws above notch (Fig. B). 2 Place remaining 2 gusset rafters on top plate, aligned over studs as shown and secure with 3" screws (Fig. B).
ROOF PANELS PARTS REQUIRED: x174 x2 2" (5,1 cm) 3/4" GAUGE BLOCK 7/16 x 15-7/8 x 23-7/8" (1,1 x 40,3 x 60,6 cm) x2 x2 7/16 x 15-7/8 x 48" (1,1 x 40,3 x 121,9 cm) x2 7/16 x 48 x 96" (1,1 x 121,9 x 243,8 cm) 7/16 x 48 x 71-7/8" (1,1 x 121,9 x 182,6 cm) x2 7/16 x 15-7/8 x 96" (1,1 x 40,3 x 243,8 cm) Roof panels may cause serious injury until securely fastened.
ROOF PANELS PARTS REQUIRED: 3 Attach a 15-7/8" x 23-7/8" panel with the rough side up (painted-grid lines side), flush with the installed 15-7/8" x 96" panel (Fig A). The panel is flush at the gable end overhang (Fig. B), and the panel is 1/2" from outside of the end rafter (Fig. C). Secure panel with two 2" (5,1 cm) nails in the corners. Fig. C Two Nails 1/2" (1,3 cm) Flush Fig. A 15-7/8" x 23-7/8" Flush at rafter ends. 4 Fig.
ROOF PANELS PARTS REQUIRED: 5 Place a 48" x 96" upper roof panel with the rough side up and flush to lower panels. Ensure 1/2" gap at gable end rafter (Fig. B) and 3/4" measurement on the rafter (Fig. A). Secure the lower edge of roof panel using two 2" nails in corners as shown. 48 3/4" (1,9 cm) x9 6" Gauge Block Move up to the top of the panel and keep spacing between the center of the rafters (Fig. C). Flush Fig. A Two Nails NAIL FIRST Secure with one 2" nail into each rafter (Fig. C). Fig.
ROOF PANELS PARTS REQUIRED: 7 Nail the roof panels using 2" nails 6" apart on edges and 12" apart inside panel. 6" (15,2 cm) 12" (30,5 cm) 8 Repeat process to attach roof panels on the opposite side. FINISH You have finished installing your roof panels.
GABLE TRIM PARTS REQUIRED: x4 x24 ATA 2 x 4 x 64-1/8" (5,1 x 10,2 x 162,9 cm) 1-1/2" (3,8 cm) LEFT x2 3/8 x 4-3/4 x 64-1/8" (1 x 12,1 x 162,9 cm) RIGHT x2 3/8 x 4-3/4 x 64-1/8" (1 x 12,1 x 162,9 cm) You will build two LEFT and two RIGHT gable trim units. BEGIN 1 Orient parts on floor. Line up 3/8" x 4-3/4" x 64-1/8" trim primed side down on top of ATA. Trim is flush with ATA at end and along edges as shown (Fig. A). Secure with 1-1/2" nails spaced evenly (approximately 12" (30,5 cm).
GABLE TRIM PARTS REQUIRED: x2 RIGHT gable trim unit x2 LEFT gable trim unit BEGIN 1 x16 3" (7,6 cm) Line up RIGHT gable trim unit flush to gable panel center seam and flush with roof sheathing (Fig. A, Fig. B). Secure with 3" screws into end rafter and spaced evenly (approximately 24" (61 cm). Fig.
GABLE TRIM PARTS REQUIRED: x4 Keystone x2 3/8 x 4-3/4 x 54-5/8" (1 x 12,1 x 138,7 cm) x48 2" (5,1 cm) 3/8 x 10 x 17" (1 x 25,4 x 43,2 cm) BEGIN Line up (10" x 17") Keystone flush to gable unit peak and flush with roof sheathing (Fig. A). 1 Secure with 2" finish nails into gable unit in pattern shown. Place fascia 4-3/4" x 54-5/8" flush to Keystone and flush with roof sheathing (Fig. B). 2 Secure with 2" finish nails into gable unit and spaced evenly (approximately 18" (46 cm).
EAVE SIDE SOFFITS PARTS REQUIRED: x2 2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm) AO x2 x4 3/8 x 4-7/8 x 73-1/2" (1 x 12,4 x 186,7 cm) x2 x36 2" (5,1 cm) 3" (7,6 cm) 3/8 x 4-7/8 x 96" (1 x 12,4 x 243,8 cm) Ensure soffit boards are flush at rafter ends (Fig. B) and flush at seam. BEGIN 1 Place eave nailer AO between two center rafters as shown. Keep AO flush to the outside edge of rafter (Fig. A, Fig. B). Pre-drill a 1/8" hole through center rafters into AO to avoid splitting rafter.
EAVE SIDE SOFFITS PARTS REQUIRED: 2 Place 96" soffit board primed side down, flush to gable trim unit and rafter ends (Fig B). Secure using 2" finish nails, two in each rafter and two into edge of AO as shown. 3 Position 73-1/2" soffit board primed side down flush to gable trim unit and rafter ends (Fig B). Secure using 2" finish nails, two in each rafter. Flush to gable trim unit Fig.
EAVE SIDE FASCIA PARTS REQUIRED: x2 x36 2" (5,1 cm) 3/8 x 4-3/4 x 77-1/4" (1 x 12,1 x 196,2 cm) x2 3/8 x 4-3/4 x 96" (1 x 12,1 x 243,8 cm) BEGIN 1 Place 77-1/4" soffit board primed side down, flush to gable trim unit and roof sheathing (Fig A). Secure using 2" finish nails, two in each rafter and two into face of AO as shown. 2 Place 96" soffit board primed side down, flush to gable trim unit and roof sheathing (Fig A).
DOUBLE DOORS - GABLE WALL PARTS REQUIRED: IMPORTANT! USE DOORS WITH HINGE BOARD ENDS PAINTED GREEN AND RED HINT: x1 x1 Left Door Right Door 3" (7,6 cm) x2 1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) OO 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) BEGIN 1 Orient parts as shown on flat surface. (right) and green (left) on hinge board. 2 Attach temporary support OO with 3" screws in middle and at ends as shown. Tighten securely. 3 Attach temporary support GAA with two 1-5/8" screws as shown.
DOUBLE DOORS - GABLE WALL PARTS REQUIRED: x1 4 x12 OO 3" (7,6 cm) 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) Attach temporary support OO as a ledger board flush under wall panels for doors to rest on, using two 3" screws (Fig. A). Center doors on panel seam as shown (Fig. B). Fig. A OO OO Flush against wall panels. 5 Screw hinge boards into wall supports and floor using ten 3" screws as shown. Make sure screws go into framing and floor (Fig. C, D).
DOUBLE DOORS - GABLE WALL PARTS REQUIRED: x1 x2 x54 DGR 3/4" (1,9 cm) 19/32 x 2-1/2 x 70-7/8" (1,5 x 6,3 x 180 cm) DGL 19/32 x 2-1/2 x 70-7/8" (1,5 x 6,3 x 180 cm) BEGIN 1 Secure door trim from inside using 3/4" screws as shown (Fig. A). Attach DGL and DGR with 3/4" screws from inside of doors (Fig. B). 2 Reinforce the door trim using 3/4" screws through door panel into trim (Fig. A). Locate screws as shown (Fig. B). Use two screws at seams. 3/4" (1,9 cm) Screws from behind. Door Panel Fig.
DOUBLE DOOR STIFFENERS - GABLE WALL PARTS REQUIRED: x2 x12 OO 2" (5,1 cm) 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) BEGIN 1 Center OO vertically on the left door in the door opening flush with the edge of door (Fig. A). Secure using (6) 2" screws through outside trim into OO (Fig. B) 2 Repeat Step 1 to install OO on right door. OO x2 FINISH You have finished installing your door stiffeners. Fig. B IT IS IMPORTANT TO HOLD THESE DIMENSIONS Center OO in door opening. Fig.
DOUBLE DOOR HARDWARE PARTS REQUIRED: x2 x1 x1 1-1/2" (3,8 cm) 4-1/2" Shaft 1/4" (0,6 cm) 1/2" (1,3 cm) Drill Bits BEGIN 1 Measure and mark location of hole on outside of right door as shown (Fig. A). Pre-drill pilot hole with 1/4" dril. Pre-drill through hole with 1/2" drill. Fig. A Keep drilled hole square to trim to avoid breaking edge of door stiffeners.
DOUBLE DOOR HARDWARE PARTS REQUIRED: 5/16" (0,8 cm) Drill Bit x2 x8 1" (2,5 cm) BEGIN 1 Place top bolt onto OO in open position with bolt ends 3/8" (1 cm) down from frame. Bolt is open when loop is contacting base (Fig A). Mark and pre-drill holes for screws. 2 Install bolt with screws supplied and drill 5/16" (0,8 cm) hole deep enough for bolt to slide into. 3 Place bottom bolt onto OO in open position with bolt ends 1/2" (1,3 cm) up from floor. Bolt is open when loop is contacting base (Fig B).
SINGLE DOOR - FRONT WALL PARTS REQUIRED: Painted Black on Ends x5 3" (7,6 cm) UNIVERSAL DOOR Left x1 Refer to Page 20 for right hand swing single door note. BEGIN 1 Install single door with black-painted hinge board. Center door in wall panel opening. Hold door in position and keep level. 2 Measure Gap (Fig. B) between door trim and wall panel as shown. Hold door in position and keep level. Hinge-board must overhang wall panel at measurement shown (Fig. C).
SINGLE DOOR TRIM - FRONT WALL PARTS REQUIRED: x1 x27 DGL 19/32 x 2-1/2 x 70-7/8" (1,5 x 6,3 x 180 cm) BEGIN 1 Secure door trim from inside using 3/4" screws as shown (Fig. A). 2 Attach DGL with 3/4" screws from inside of door. (Fig. B). 3 Reinforce the door trim using 3/4" screws through door panel into trim (Fig. A). Locate screws as shown in Fig. B. Use two screws at seams. 3/4" (1,9 cm) Screws from behind. Door Panel Fig. A 3/4" (1,9 cm) Screws from behind. Door Trim Fig.
DOOR STIFFENER & WEATHER STRIP - FRONT WALL PARTS REQUIRED: x1 x6 OO 1-1/4 x 2-1/2 x 69" (3,2 x 6,3 x 175,3 cm) x2 LRA x20 2" (5,1 cm) 2" (5,1 cm) 1 x 4 x 69-3/4" (2,5 x 10,2 x 177,2 cm) BEGIN Center OO vertically on door in the door opening (Fig. A) 1" from edge of door (Fig. B). 1 Secure using (6) 2" screws through outside trim into OO (Fig. B) OO Fig. B Fig. A 1" (2,5 cm) IT IS IMPORTANT TO HOLD THIS DIMENSION Center OO in door opening.
DOOR HARDWARE - SINGLE DOOR PARTS REQUIRED: x2 1-1/2" (3,8 cm) x1 x1 5-1/2" Shaft 1/2" (13 mm) Drill Bit 1/4" (6 mm) Drill Bit BEGIN 1 Measure and mark location of hole on outside of door as shown (Fig.A). Pre-drill pilot hole with 1/4" dril. Pre-drill through hole with 1/2" drill. Keep drilled hole square to trim to avoid breaking edge of door stiffener. Fig.
CORNER TRIM PARTS REQUIRED: x8 x48 2" (5,1 cm) 3/8 x 1-3/4 x 81-1/2" (1 x 4,4 x 207 cm) ¸1 BEGIN 2 Attach one 81-1/2" trim board flush under soffit panel and against eave wall (Fig. A, B) using one 2" finish nail at top as shown. Position 81-1/2" trim board flush along edge of installed 81-1/2" trim board and flush under gable panel (Fig. A, B). Secure using one 2" finish nail at top as shown. Finish attaching trim flush to corners (Fig. B) using (6) 2" (5,1 cm) finish nails as shown.
COLLAR TIES PARTS REQUIRED: x2 x12 JF 2" (5,1 cm) 1 x 4 x 60" (2,5 x 10,2 x 152,4 cm) BEGIN 1 Position and level collar ties JF on 3rd and 5th rafters from double door wall. HINT: For best appearance install collar ties on rafters facing away from double door opening. 2 Attach with 2" nails as shown. JF Flush LEVEL r afte R 3rd 5t r fte a hR 2" (5,1 cm) Nails FINISH You have finished installing your collar tie.
WINDOWS PARTS REQUIRED: x2 x8 Window 22-1/4 x 29-3/4" (56,5 x 75,6 cm) 1-5/8" (4,1 cm) BEGIN 1 Seal windows with high-quality exterior-grade caulk before installing (Fig. A). 2 Center and secure windows using 1-5/8" screws as shown. Ensure window is level. Fig. A Fig. B CENTER Caulk behind frame near edge. 1-5/8" (4,1 cm) Screws CENTER FINISH You have finished installing your windows.
SHUTTERS & WINDOW TRIM PARTS REQUIRED: x4 x4 x20 DJA 1" (2,5 cm) x14 2" (5 cm) 19/32 x 2-1/2 x 11" (1,5 x 6,3 x 27,9 cm) x4 DHA 19/32 x 5-1/2 x 30-1/8" (1,5 x 14 x 76,5 cm) AZ 19/32 x 2-1/2 x 30-1/8" (1,5 x 6,3 x 76,5 cm) BEGIN 1 Position DHA on top of DJA primed side down as shown. Square and mark. Attach DHA using 1" screws. DHA 1" (2,5 cm) Screws Flush DJA 2-1/2" (6,3 cm) Parts primed side down Flush x2 2-1/2" (6,3 cm) 2 Repeat Step 1 to build 2nd shutter.
WINDOW TRIM (cont.) x17 PARTS REQUIRED: x1 NRA 19/32 x 6-7/16 x 5-1/2" (1,5 x 17,5 x 14 cm) x1 5 DEA 2 x 3-1/2 x 55" (5,1 x 8,9 x 139,7 cm) x1 AUA 2 x 2-1/2 x 53" (5,1 x 6,3 x 134,6 cm) Locate DEA and AUA centered and flush to shutters as shown. Attach using 2" finish nails. Nail into framing.
DOOR TRIM PARTS REQUIRED: x10 x2 NRA 19/32 x 6-7/16 x 5-1/2" (1,5 x 17,5 x 14 cm) x1 JTA 19/32 x 6-7/16 x 2" (1,5 x 16,4 x 5,1 cm) x1 DDA x1 DFA 19/32 x 3-1/2 x 72" (1,5 x 8,9 x 182,9 cm) x1 ZJ 19/32 x 2-1/2 x 72" (3,2 x 6,3 x 182,9 cm) 19/32 x 3-1/2 x 40" (1,5 x 8,9 x 101,6 cm) BEGIN 1 Center trim DFA over double doors flush to hinge boards. Secure using 2" finish nails into framing as shown (Fig. A). 2 3 2" (5 cm) Locate JTA centered over trim (Fig. B).
DOOR TRIM PARTS REQUIRED: x19 x1 NRA 19/32 x 6-7/16 x 5-1/2" (1,5 x 17,5 x 14 cm) x1 DDA x1 ZJ 2" (5 cm) x1 JTA 19/32 x 6-7/16 x 2" (1,5 x 16,4 x 5,1 cm) 19/32 x 3-1/2 x 40" (1,5 x 8,9 x 101,6 cm) 19/32 x 2-1/2 x 72" (3,2 x 6,3 x 182,9 cm) BEGIN 1 Flush ZJ with bottom of wall panel and single door (Fig. D). Ensure 3/8" gap between door and trim (Fig. D). CENTER CENTER Flush 2" (5,1 cm) Finish Nails into wall frame Flush Fig. D Secure using 2" finish nails into framing as shown.
DOOR - DECORATIVE HINGES PARTS REQUIRED: x18 1" (2,5 cm) x6 BEGIN 1 Level decorative hinges in position as shown. Secure with 1" (2,5 cm) screws. 1" (2,5 cm) Screws Flush 1" (2,5 cm) Screws Flush FINISH You have finished installing your decorative door hinges.
GABLE VENTS PARTS REQUIRED: x2 x2 2" (5 cm) Vent with Frame #15021 ¸1 BEGIN Place vent in gable opening. Seal vent behind vent flange edges with high-quality exterior-grade caulk before installing (Fig. A). Fig. A 2 Center vent frame over vent. Ensure frame is level. Seal vent trim from behind with high-quality exterior-grade caulk before installing (Fig. B). 2" (5 cm) Nails Fig. B 3 Secure vent frame using 2" finish nails (Fig. B).
PAINT & CAULK - NOT INCLUDED - • Use acrylic latex caulk that is paintable. Caulk at all horizontal and vertical seams, between the trim and walls, and all around the door trim. • Use a high quality exterior acrylic latex paint. When painting your building, there are a few key areas that can be easily overlooked that must be painted: • Bottom edge of all siding and trim • Inside of doors and all 4 edges Note: Prime all un-primed exterior wood before painting. (Follow directions provided by manufacturer.
SHINGLES - NOT INCLUDED • Follow directions provided by manufacturer and these instructions. Familiarize yourself with a 3-Tab Shingle. Notch SHINGLE NAIL PATTERN 1" (2,5 cm) 1/2" (1,3 cm) Notch Sealing Strip 1" (2,5 cm) Half A Rain Slot Full Rain Slot NAILS NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS. BEGIN 1 Install first starter row upside down and color up with a 1" overhang at back and bottom of roof panel. Use (4) nails per shingle.
SHINGLES continued... 2 2 Beginning at front of shed, install first row of shingles with notch at 1" past roof edge or flush with drip edge. Roof Deck FRONT OF SHED 1" (2,5 cm) Notch BACK OF SHED Flush with starter row. - or - Drip Edge Flush with starter row. Notch 3 Install second row of shingles flush at top of first row's rain slots. Ensure 1" overhang or flush to drip edge at front, stagger each row. FRONT OF SHED BACK OF SHED 1" (2,5 cm) Notch Flush with rain slots.
SHINGLES continued... 5 Continue installing rows of shingles to the peak. At the peak make sure there is a maximum of 5" or less to the rain slot, as shown below. If shingles overlap at ridge cut to peak with a utility knife. Cut Off. 5" (12,7 cm) MAX. CUT Top of rain slot. 5" (12,7 cm) or less. • If more than 5" to rain slot you must install another row of shingles. 6 Repeat steps 1 - 5 to shingle the opposite side of your roof. Trim shingles at ridge.
SHINGLES - RIDGE CAP • You will finish off the top of the roof with a ridge cap made from shingles. BEGIN 1 Cut shingles into THREE pieces. Hint: Use cut-off pieces first. 2" (5 cm) 2" (5 cm) 2" (5 cm) 2" (5 cm 2" (5 cm) 2" (5 cm) Score shingle, then snap-off angled cut. Weather Seal Top of slot. Note: • You will need about 32 - 34 cut pieces. 2 32 to 34 Pieces Install first ridge cap flush to shingles at front, as shown. (1) Nail per side through weather seal.
SHINGLES - RIDGE CAP continued... 4 Continue installing ridge cap to back of roof. 5 Make sure there is 4" between the shingle-color and edge of shingles. 4" (10 cm) 6 Trim cap off flush to shingles When you have 4" minimum of shingle color cut one piece to cap your roof. Cut at top of rain slot. Cap 7 Install flush to shingles. Flush to shingles (2) Nails per side. FINISH You have finished your ridge cap.
WARRANTY REGISTRATION Please complete your warranty registration to properly validate your warranty. Register your product online at:www.OnlineWarranty.net. LIMITED CONDITIONAL WARRANTY* Backyard Storage Solutions, LLC warrants the following: 1. Every product is warranted from defects in workmanship and manufacturing for 1 year. 2. All accessories, hardware and metal components are warranted for 2 years. 3. All Oriented Strand Board (OSB) is warranted for 2 years 4.
