Save This Manual for Future Reference YARDMAN = Chipper Shredder Operator's Manual MODEL NUMBER YW7565 SERIAL NUMBER LL PURCHASE DATE Both made! number and serial number may be found on the main label, You should record both of them In a safe place for future use.
Your new YARDMAX® chipper shredder offers quality construction, and is easy and safe to operate. With proper use and care, it is designed to give you many years of dependable service. Prepare to experience the durability to take on any job with the ease, portability, and convenience of your new chipper shredder! Discover the YARDMAN Advantage AL YARDMAN, we understand that land ownership definitely has its privileges, but it also comes with a great deal of responsibility.
A Carefully read through this entire operator's martial before using your new unit. Pay attention to aff cautions and warnings. This unit is a gasoline engine driven chipper shredder. It is designed to cut wood into chips. It offers quality solid steel construction and is easy and safe to operate. With proper use and care, if should give you many years of dependable service.
Mabel Number Engine Displacement: Torque fit-Ibs, gross) ERADICABLE Approval Chipping Capacity. Chipper Blades Reduction Rate Hopper Opening Discharge Chute Tires oll Fuel Capacity Product Weight YWPSE5RMOS 1807.
SAFETY GENERAL SAFETY RULES UNDERSTAND YOUR MACHINE Read this manual and labels affixed fo the machine to understand its imitations and potential hazards, Be thoroughly familiar with the controls and their proper aeration. Know how to stop the machine and disengage the controls quickly, Make sure to read and understand all the instructions and safety precautions as outlined in the Engine Manufacturer's manual packed separately with your unit.
ENGINE SAFETY This machine is equipped with an internet combustion engine. Da not use on or near any unimproved, forest covered, or brush covered land unless the exhaust system is equipped with a spark arrested meeting applicable focal, state, or federal laws. in the state of California, a spark arrested is required by law. Other states have similar laws, A spark arrested, if used, must he maintained in effective working order by the operator.
Heep your face and: ody back from the chipper hopper ang. discharge chute to avoid injury from accidental bounce back of ministerial Never therewith our hands inside the feed hopper pastiche. rubber flap while operating the'machine! Keen combustible substances away from the engine when iris hot: not tit the machine while the gaming i convincing.
Avail contact with hot fuel, ofl exhaust fumes and hat surfaces. Dio not touch the engine or muffler. These parts get extremely hot Sam person They remain Motion a short time fare ved tum aff the unit.
CONTENTS SUPPLIED Your YARDMAN chipper shredder comes partially assembled and contains the following: . Main Machine Lower Feed Hopper . Upper Feed Hopper Discharge Chute . Engine Ol wae Ne 9 | Contents Supplied Fuel Cap . Operator's Manual & Engine Manual . Tools for Spark plug Assembly .
Chipper Shredder » Generator s Anus] ASSEMBLY This chipper shredder was partially assembled at the factory: following the below assembly instructions to do assembling DEFLECTOR loosen the deflector lever in counter-clockwise direction to adjust discharge age. Tighten lt in the do devise direction {See Fins 3 DISCHARGE CHUTE 1: Loosen elocution which holds the discharge chute on he machine. 2: Remove the MBX2S bolts, fiat washers, and nuts from the Housing. Set aside for later use.
Chipper Shredder » Operator's Manual KNOW YOUR MACHINE FEATURES AND CONTROLS Feed Hopper FE Discharge Chute A hats IMPROVISES 1BU7 Know Your Machine | 12
FEED HOPPER The feed hopper is where you insert your materials fo » be chipped. DISCHARGE CHUTE Chipped materials are discharged through this » opening The deflector can be attached to the chute. GRIP HANDLES The handles are used to move the unit. TRANSPORT WHEELS “fo move the chipper shredder, grip the handles located Fy on the top of the opening of the hipper and tilt the machine back until it is fully resting on the tires.
Chipper Shredder » Operator's Manual 2. Remove the fuel filler cap and fill the tank, (Ses engine manual for fuel capacity, fuel recommendation, and location of fuel cap} IMPORTANT. DO NOT OVERFILL! 3. Open the fuel shut-off valve, This equipment and/or its engine may include evaporation emissions control system components, required to meet EPA candor CARP regulations, that will any function properly when the fuel tank has been filled to the recommended revel.
feed limbs or branches through cut-end first, leaving the bushy head on. This helps guide the limb down the feed hopper and reduces spinning and bouncing of small pieces back up the feed hopper. Some side branches may require per-cutting so that the branch will self-feed more efficiently. it is always advisable to process freshly cut materials, as wooden branches get very hard, they become springy when dried out and can make the knives dull more quickly.
Chipper Shredder » Generator s Anus] TRANSPORTING Our AROMA chipper shredder is equipped with twa large prismatic wheels for easy movement by hand To move the unit grip the handles and. Hil the dipper atraddearsliphily after wiki sing the ofl Len covers liverwort MAINTENANCE Maintaining your YARDMAN chipper shredder will ensure long: Hie tis the aching snd HS components.
There are two bearings, ore outside and the vibe inside Fhe housing The beading ans greased when thespians new but it commendation to grease them after 2 couple Hooking cif lies One or ved Burr i Sufficient, Be childcare 0k to over: grease. Over: lubrication: tan damaged the bearings. tense the outside bearing 1: Open the plastic tine: {Sex Figure 11) 2 Crease the outside bearing through the Al ling Hole.
KNIFE REMOVAL AND REPLACEMENT Tie chipper gadder ie equipped ety twa crisper waives mounted on the Nutting disk, When the knives get dull or show! visible nicks, the machine will Jose its self feeding action and the material has fo be pushed Ino Often it comes out in long strips. Helices the knifes by following steps.
A Be careful and wear gloves when working aerator the. knives. 7. Remove the dull or damaged rives and visually inspect the: cutting disk slot and knives mounting rage. Make sure they're Guam and that thees placental vies with te ble 16 mongol flush against the cutting disk. Remount new or sharpened knives with the knife edges facing up.
Top View: Inside blade § anvil setup Cutting Disk sere fo position of Rotor Shaft Saar Plate Onsite Blade op View: outside blade Bani set un ~ Cutting Disk i hl Rotor Shalt @ 8 Wear Plate Outside Blade Figure 20 Prepare two pieces of cardboard, ans Imm thick, other is Sims thick They are Usually good ap ligates Tor resetting the wear plate. 1. Remove the feed hopper. (See Fare 13) Fi nee dive Bolts Bat fits wiser plies 3.
di Remove the top Belt guard hitherto Front halting by taking oft Remove the too belt guard from tha Front haloing by taking oft the fixing bolts: the fixing Holst. (See Figure 22) = Wiesenthal hwo MIZ adjustment nuts By turning them counters incise and moving them downward to reduce any slack in the Vi: baits.
i Remove the upper belt guard from the front housing dnd the: lower belt guard from the engine base by taking off the fishing Hits respectively. Gee Figure 26) Belt Cover Figure 26 4. Remove the four engine mounting bolts that secure the engine fo the engine base and slide the engine downward until the engine pulleys disengaged from the helot Remove engine from engine plate and place on the Side of unit.
STORAGE {four chipper shredder will not be sed for move than 30 days, follow the steps below (0 prepare your uniformity storage: 1 Drain the fuel tank completely Stale fuel hag high stm content and can clog Bie bicarbonate and restrict foe flow, stark the engine and allow it to run until 5 stops. This ensures noc fuse is left in the carburetor and holes prevent deposits from: forming inside which can damage the engine. 3 Drain the ofl farm the engine while IU is ati wars.
Chipper Shredder » Generator s Anus] Engine runs erratically Engines overheats Chipping action seems toa slow, cutting disk stalls.
