3” (33 CM) CORDLESS GRASS TRIMMER model number 060-1983-0 | contact us: 1.866.523.5218 3026035 IMPORTANT: Read and follow all safety rules and operating instructions before using this product.
model no. 060-1983-0 | contact us: 1.866.523.
Introduction 4 Safety Instructions and Symbols 5 Product Specifications 9 Product Diagram 10 Assembly 11 Operation 12 Maintenance 18 Storage 18 Troubleshooting 19 Exploded View 20 Parts List 21 Warranty 22 Table of Contents model no. 060-1983-0 | contact us: 1.866.523.
model no. 060-1983-0 | contact us: 1.866.523.5218 Please do not operate garden equipment near children. This could lead to severe injury or death. Introduction INTRODUCTION Congratulations on your purchase of your new Yardworks® tool. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact our Yardworks® customer service line at 1.866.523.5218.
FOR ALL APPLIANCES • • • • • • • • • • • • Avoid dangerous environments — do not use appliances in damp or wet locations. Don’t use in rain. Keep children away — all people and pets should be kept at a distance from the work area. Dress properly — do not wear loose clothing or jewellery. They can be caught in moving parts. Wear protective clothing; use of work gloves, long pants, a long-sleeved shirt and safety footwear is recommended when working outdoors.
Safety Instructions model no. 060-1983-0 | contact us: 1.866.523.5218 7. 8. 9. 10. 11. additional medical help. Liquid ejected from the battery may cause irritation or burns. Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable Canadian spelling resulting in fire, explosion or risk of injury. Do not expose a battery pack or appliance to fire or excessive temperature.
q) The battery pack gives its best performance when it is operated at normal room temperature (20°C ± 5°C/68°F ± 9°F). r) When disposing of battery packs, keep battery packs of different electrochemical systems separate from each other. s) Recharge only with the charger specified by Yardworks® . Do not use any charger other than that specifically provided for use with the equipment. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
model no. 060-1983-0 | contact us: 1.866.523.5218 Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product effectively and safely.
Product Specifications model no. 060-1983-0 | contact us: 1.866.523.5218 PRODUCT SPECIFICATIONS Voltage No Load Speed Cutting Diameter Line Diameter Line Length Battery Capacity (060-1987-2) Charger Input (060-1990-2) 48 V 7000/min 13” (33 cm) 0.080” (2.0 mm) 2x8ft (4.9 m) 2.0 Ah 120 V~, 60 Hz, 110 W Charger Output (060-1990-2) Charging Time Machine Weight ,2A 48 V 1 hr 11 lb (5 kg) SUITABLE BATTERY PACKS Item Number Battery Capacity 060-1987-2 ABP4830SH 060-1988-0 ABP4850SH 060-1989-8 2.
model no. 060-1983-0 | contact us: 1.866.523.5218 Product Diagram 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Battery pack (060-1987-2) Battery pack release button On/Off switch Lock-off button Auxiliary handle Connector Safety guard Line cutter Trimmer head Spool Bump knob Charger (060-1990-2) Wrench (Fig. A1) Screws (Fig. B) 1 2 Tool storage 3 4 5 6 7 8 9 11 10 12 We recommend that you purchase your accessories listed in the above list from the same store that sold you the tool.
model no. 060-1983-0 | contact us: 1.866.523.5218 To reduce the risk of injury, user must read instruction manual 1. ASSEMBLING THE UPPER SHAFT AND LOWER SHAFT 1) Loosen the bolt on the connector. (see Fig. A1.) 2) Align and insert the lower shaft directly into the upper shaft. (see Fig. A2.) 3) Position the locking/release button into the guide recess. (see Fig. A2.) 13 Locking/ Guide recess Release knob Locking/ Guide recess Release knob A1 A2 A2 14 14 B B 2.
Locking/ Guide recess Release knob A1 A2 14 model no. 060-1983-0 | contact us: 1.866.523.5218 3. Assembling the safety guard Attach the safety guard to the trimmer head. Align the guard so it slides into the slots located on the trimmer head. (see Fig. C1.) Secure the safety guard onto the trimmer head with the screw provided. (see Fig. C2.) Operation B C1 C2 BEFORE OPERATION 1.
model no. 060-1983-0 | contact us: 1.866.523.5218 A1 D A2 15 CHARGING INDICATOR This charger is designed to detect some problems that can arise with battery packs. Indicator lights indicate problems (see table below). Light ON/ Flash Status Defective battery. Red on B Battery Temperature Protection. The temperature of battery pack is less than 0oC (32oF) or more than 40oC (104oF). Red flash Fully charged. Green on Charging. Green flash 2.
Release knob 14 A2 C1 B C2 14 2 model no. 060-1983-0 | contact us: 1.866.523.5218 1 1. SWITCH ON/OFF To switch on, press the lock-off button first, then the On/Off Switch. (See Fig. F.) B off, release the On/Off Switch. To switch C1 E E 2 2 1 1 Operation C2 300 F C2 G1 E E 2. TRIMMING 2 1) Keep the trimmer head at an angle of about 30° to the ground when2trimming. (See Fig. G1.
E model no. 060-1983-0 | contact us: 1.866.523.5218 300 G1 G2 G3 G4 H 300 G3 Operation G1 3. ADJUSTING CUTTING LINE LENGTH—AUTOMATIC BUMP LINE FEED The trimmer head allows the operator to release more 2 cutting line without stopping the motor. As line becomes frayed or worn, additional line can be released by lightly tapping the bump knob on the ground while operating the trimmer. (see Fig. H.) 1 becomes too dull.
F F G1 G1 Operation model no. 060-1983-0 | contact us: 1.866.523.5218 4. TO REPLACE THE SPOOL AND LINE G3 G2 1) For G2 your convenience, it is recommendedG3 you buy a replacement spool with line. 2) Press and hold in the two cap release latches. Loosen the cap by rotating it counterclockwise. Pull cap away from the spool holder. (see Fig. I1.) 3) Remove old spool. (see Fig. I2.) 4) Place new spool into cutting head. Release one line from cleat and feed line through eyelet. (see Fig. I3.
1 I1 1 17 I2 model no. 060-1983-0 | contact us: 1.866.523.5218 1 I3 I4 J1 J2 WARNING! Your trimmer is designed to only use line with a maximum diameter of 0.08” (2 mm). Always remove the battery pack from your trimmer after use. Operation 2 5. TO REPLACE THE LINE ON THE SPOOL 1) Cut a piece of line approximately 16’ (4.9 m) long. 2) Insert the centre point of line into the notch in the middle section of the spool and wind the line in a clockwise direction as shown. (see. Fig. J1.
model no. 060-1983-0 | contact us: 1.866.523.5218 Maintenance MAINTENANCE Always check the product prior to use for any damage. After use, disconnect the battery from the tool and check for damage. Your power tool requires no additional lubrication or maintenance. There are no userserviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry, roomtemperature location.
model no. 060-1983-0 | contact us: 1.866.523.5218 Problems Trimmer fails to operate. Possible Causes Corrective Action Battery discharged. Recharge battery; also see the content in charger manual. Allow to cool/warm. Contact Yardworks® at 1.866.523.5218. Contact Yardworks® at 1.866.523.5218. Battery too hot/cold. Motor is broken. Internal wiring of machine damaged. Motor is broken. Battery not fully charged. On/Off switch defective. Machine defective. Line spool is not wound well.
46 47 48 49 50 51 54 53 52 55 56 57 58 45 44 Exploded View 20 model no. 060-1983-0 | contact us: 1.866.523.
NO.
model no. 060-1983-0 | contact us: 1.866.523.5218 FIVE-YEAR LIMITED WARRANTY Warranty For five (5) years from the date of purchase within Canada, YARDWORKS CANADA will, at its option, repair or replace for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship (excludes battery).
model no. 060-1983-0 | contact us: 1.866.523.5218 FCC Part 15 Supplier’s Declaration of Conformity Product Description: 48V 2.0A Charger Model Number: 060-1990-2 Trade Name: YARDWORKS® This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Responsible Party: Positec USA, Inc.
1 13” (33 CM) CORDLESS GRASS TRIMMER Item # 060-1983-0 | contact us: 1.866.523.5218 Quick Start Guide 1. ASSEMBLING THE UPPER SHAFT AND LOWER SHAFT a) Loosen the bolt on the connector. (See Fig. A1.) b) Align and insert the lower shaft directly into the upper shaft. (See Fig. A2.) c) Position the locking/release button into the guide recess. (See Fig. A2.) A1 A2 Locking/ Guide Locking/ Guiderecess recess Release Releaseknob knob 2.
2 13” (33 CM) CORDLESS GRASS TRIMMER Item # 060-1983-0 | contact us: 1.866.523.5218 BEFORE OPERATION 1. CHARGING PROCEDURE (SEE FIG. D.) a) Plug the charger into an appropriate outlet. b) Slide the battery pack into the charger; the light will begin flashing green to indicate the charging process has started. c) When charging is completed, the light will turn solid green. The pack is now fully charged; unplug the charger and remove the battery pack. D 2.