Specifications

YASKAWA Inverter Drive A1000 – Crane Software Application Manual
61
No. Parameter Name Default
Setting
Value
No. Parameter Name Default
Setting
Value
E2-04 Number of Motor Poles 4 F1-01 PG Pulses 1024
E2-05 Motor Resistance Between Lines 9.842 F1-02 Operation Selection at PG Open Circuit (PGo) 1
E2-06 Motor Leakage Inductance 18.2 F1-03 Operation Selection at Overspeed (oS) 1
E2-07 Motor Iron Core Saturation Coefficient 1 0.50 F1-04 Operation Selection at Deviation 3
E2-08 Motor Iron Core Saturation Coefficient 2 0.75 F1-05 PG 1 Rotation Selection 0
E2-09 Motor Mechanical Loss 0.0 F1-06 PG 1 Division Rate 1
E2-10 Motor Iron Loss for Torque Compensation 14 F1-07 Integral Value During Accel/Decel Selection 0
E2-11 Motor Rated Power 0.40 F1-08 Overspeed Detection Level 115
E3-01 Motor 2 Control Method 2 F1-09 Overspeed Detection Delay Time 0.0
E3-04 Motor 2 Max Output Frequency 50.0 F1-10 Excessive Speed Deviation Detection Level 10
E3-05 Motor 2 Max Voltage 200.0 F1-11 Excessive Speed Deviation Detection Delay Time 0.5
E3-06 Motor 2 Base Frequency 50.0 F1-12 Number of PG 1 Gear Teeth 1 0
E3-07 Motor 2 Mid Output Freq. 3.0 F1-13 Number of PG 1 Gear Teeth 2 0
E3-08 Motor 2 Mid Output Freq. Voltage 14.4 F1-14 PG Open-Circuit Detection Time 2.0
E3-09 Motor 2 Min. Output Freq. 0.5 F1-20 PG 1 Disconnect Detection 1
E3-10 Motor 2 Min. Output Freq. Voltage 3.0 F1-21 PG 1 Signal Selection 0
E3-11 Motor 2 Mid Output Frequency 2 0.0 F1-30 PG Card Option Port for Motor 2 Selection 1
E3-12 Motor 2 Mid Output Frequency Voltage 2 0.0 F1-31 PG 2 Pulses Per Revolution 1024
E3-13 Motor 2 Base Voltage 0.0 F1-32 PG 2 Rotation Selection 0
E4-01 Motor 2 Rated Current 1.90 F1-33 PG 2 Gear Teeth 1 0
E4-02 Motor 2 Rated Slip 2.90 F1-34 PG 2 Gear Teeth 2 0
E4-03 Motor 2 Rated No-Load Current 1.20 F1-35 PG2 Division Rate for Pulse Monitor 1
E4-04 Motor 2 Motor Poles 4 F1-36 PG2 Option Card Disconnect Detection 1
E4-05 Motor 2 Line-to-Line Resistance 9.842 F1-37 PG 2 Signal Selection 0
E4-06 Motor 2 Leakage Inductance 18.2 F2-01 Analog Command Option Card Operation Selection 0
E4-07 Motor 2 Motor Iron-Core Saturation Coefficient 1 0.50 F2-02 Analog Input Option Card Gain 100.0
E4-08 Motor 2 Motor Iron-Core Saturation Coefficient 2 0.75 F2-03 Analog Input Option Card Bias 0.0
E4-09 Motor 2 Mechanical Loss 0.0 F3-01 Digital Input Option Card Selection 0
E4-10 Motor 2 Iron Loss 14 F3-03 DI-A3 Data Bit Size 2
E4-11 Motor 2 Rated Capacity 0.40 F4-01 Terminal V1 Monitor Selection 102