Instruction manual

16
 Input/Output Terminal Status - - - - - - - - - - - - - - - - - - - - - - - - - 49
 Data Reception Error Display - - - - - - - - - - - - - - - - - - - - - - - - 49
 Simple Data Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 51
6. Programming Features - - - - - - - - - - - - - - - - - - 53
 Constant Setup and Initialization - - - - - - - - - - - - - - - - - - - - - - 53
 Constant Selection/Initialization (n001) - - - - - - - - - - - - - - - - - 53
 Using V/f Control Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - 55
 Adjusting Torque According to Application - - - - - - - - - - - - - - -55
 Using Vector Control Mode- - - - - - - - - - - - - - - - - - - - - - - - - - 58
 Precautions for Voltage Vector Control Application - - - - - - - - - 58
 Motor Constant Calculation- - - - - - - - - - - - - - - - - - - - - - - - - - 59
 V/f Pattern during Vector Control - - - - - - - - - - - - - - - - - - - - - - 60
 Switching LOCAL/REMOTE Mode - - - - - - - - - - - - - - - - - - - - 61
 How to Select LOCAL/REMOTE Mode - - - - - - - - - - - - - - - - - 62
 Selecting RUN/STOP Commands - - - - - - - - - - - - - - - - - - - - - 62
 LOCAL Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 62
 REMOTE Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 63
 Operating (RUN/STOP Commands) by Communications- - - - - 63
 Selecting Frequency Reference - - - - - - - - - - - - - - - - - - - - - - 63
 LOCAL Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 64
 REMOTE Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 64
 Setting Operation Conditions - - - - - - - - - - - - - - - - - - - - - - - - 65
 Reverse Run Prohibit (n006)- - - - - - - - - - - - - - - - - - - - - - - - - 65
 Multi-step Speed Selection - - - - - - - - - - - - - - - - - - - - - - - - - - 65
 Operating at Low Speed - - - - - - - - - - - - - - - - - - - - - - - - - - - - 66
 Adjusting Speed Setting Signal - - - - - - - - - - - - - - - - - - - - - - - 67
 Adjusting Frequency Upper and Lower Limits - - - - - - - - - - - - - 68
 Using Four Acceleration/Deceleration Times - - - - - - - - - - - - - 68
 Momentary Power Loss Ridethrough Method (n081) - - - - - - - - 70
 S-curve Selection (n023) - - - - - - - - - - - - - - - - - - - - - - - - - - - 71
 Torque Detection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 72
 Frequency Detection Level (n095) - - - - - - - - - - - - - - - - - - - - - 73
 Jump Frequencies (n083 to n086) - - - - - - - - - - - - - - - - - - - - - 74
 Continuing Operation Using Automatic Retry Attempts (n082) - 75
 Operating a Coasting Motor without Tripping - - - - - - - - - - - - - 75
 Holding Acceleration/Deceleration Temporarily - - - - - - - - - - - - 76