About This Guide VP-2009(P) Elite is an H.264 based broadband videophone supporting Video and Voice applications. Its major functions include IP Telephony, IP Camera Viewer (SIP based) and Photo frame. It can satisfy the demanding requirements of the next generation of IP broadband communication applications and open the door to the world of multimedia. VP-2009(P) Elite is an innovative IP media phone equipped with the most advanced video compression technology.
1 Safety Precautions General Requirements Before you install and use the device, read these safety precautions carefully and observe them during operation. During storage, transportation, and operation, keep the device dry. During storage, transportation, and operation, avoid collision and crash for the device. Never attempt to dismantle the device by yourself. In case of any fault, contact the appointed maintenance center for repair.
During lightning whether, stop using the device and disconnect it from the power supply. Unplug the power plug and the Asymmetric Digital Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid lightning strike. If the device is not used for a long time, disconnect it from the power supply and unplug the power plug.
Contents 1 Safety Precautions .................................................................................................................................... 1 2 Getting Started ...................................................................................................................................... - 1 Packing List .........................................................................................................................................................
TV Output ................................................................................................................................................ - 33 Setting the Send Key ................................................................................................................................ - 33 Anonymous Call ....................................................................................................................................... - 34 Directory ...............................
Using Speed Dial to Make a Call ............................................................................................................. - 70 Answering a Call ............................................................................................................................................... - 71 Answering a Single Call ........................................................................................................................... - 71 Answering Multiple Calls......................
IP Video Phone 2 Getting Started Getting Started Packing List The following components are included in your package: IP Video Phone VP-2009(P) Elite Power Adapter Handset & Handset Cable -1-
IP Video Phone Ethernet Cable Quick Installation Guide & Quick Reference CD Content Getting Started Please unpack the product package with caution; inspect the items closely. If you find any damaged item, please contact your IP Video phone reseller immediately. Also, please keep the box and packing material for future use in the event of future shipments. Assembling the Phone This section introduces how to assemble the phone.
IP Video Phone Getting Started Headset is not included in the packing list. Should be purchased separately. Connect Network and Power There are two ways for network and power source connections. You can connect the phone to the AC Power directly using the power adapter or to a PoE compliant switch or hub. Your system administrator will advise you on which one to use. If inline power is provided, do not install AC adapter. Make sure the Ethernet cable and switch/hub is PoE compliant.
IP Video Phone Getting Started Configuration and Registration Configuring via Web Page Press button on the keypad of the phone to enter the status page and find out the IP address of the IP video phone. Enter it (for example http://10.1.3.204) into the address bar of web browser. The default login name and password are admin/admin. Please locate your PC in the same network segment of IP phone (10.1.3.X) to access the web configuration page. Please consult your system administrator for help.
IP Video Phone 3 Overview Overview Keypad Instruction Figure 3-1 Keypad instruction You can check the following list which introduces the IP phone’s keypad in detail: Table 3-1 Key on the keypad Key Description Event Status Indication LED It will show the event status of the video phone. For more details you can refer to “LED Instruction”. Power Indication LED Indicates the power supply status. When VP-2009(P) Elite is powered on, the indicator is on.
IP Video Phone Overview Key Description Speaker Answers an incoming call. On the dialing page or conversation page, press this key to change the conversation mode. Enable or disable DND function. DND Enter the contact page. Contact Navigation Key Includes four arrow keys (up, down, left, and right), and one key. Arrow keys： Move the cursor on difference pages. In the standby state: press left or right key to switch the standby state.
IP Video Phone Overview Table 3-4 ICON instruction Icon Description Network Status: Available Network Status: Unavailable Network Status: Limited Flashes when the internet is disconnected. Account register successful or the DSS key set as line, and the line is registered. Account register failed or the DSS key set as line, and the line is unregistered.
IP Video Phone Overview User and Administrator Mode Your phone can be used in user or administrator mode. Administrator mode is the default setting with full configuration rights. The default administrator password is admin. The default user password is user.
IP Video Phone 4 Configuring VP-2009(P) Elite Customizing Your Phone Powering Up the Video phone Step 1 Plug a Network cable into the network port. Step 2 Plug in power. Step 3 It takes about 2 minutes to boot up the video phone. During this period, please do not touch any keys or turn off the video phone. The Idle Interface The phone has 4 idle interfaces (Standby state, Main menu, Picture Dial and DSS Key).
IP Video Phone Configuring VP-2009(P) Elite Area Description 4 Use the clock to display the current time，user can use fingers drag this clock, placed it at any position of this interface. 5 Display the Quick function keys. The default is “History”, “Directory”, “Message” and “Setting”. 6 This area is showing the background picture. User also can change it. For more information you can refer to “Display”.
IP Video Phone Configuring VP-2009(P) Elite Menu Interface Second level submenu Message ---- Photo Media Video Contact Picture Application Door Phone Call Feature DSS Key ---- Picture Dial ---- Voice Mail ---- Hotline ---- Forward ---- Call Waiting ---- Auto Answer ---- Video ---- Tv Output ---- Key as Send ---- Anonymous Call ---- Account ---- Network ---- Call Feature Setting Display ---- Date & Time ---- Sound ---- Security ---- Personali
IP Video Phone Configuring VP-2009(P) Elite Picture Dial This function key allows you to set the most frequently dialed numbers easily. The phone supports six contacts and allows user to choose the contacts picture. Switch the idle interface to Picture dial page, and then click the corresponding picture, if the picture is set with a number, the phone will dial the number directly. If not, the phone will turn to the configure page.
IP Video Phone Configuring VP-2009(P) Elite Figure 4-4 DSS key - 13 -
IP Video Phone 5 Configuring VP-2009(P) Elite Configuring VP-2009(P) Elite Setting Interface User can configure many functions, such as: Account, Network, Call Feature, Display, Date & Time, Sound, Security, Personalize, Reset, Reboot and Calibration, To access the Setting page, proceed as follows: Step 1 Press the Left/Right navigation key in the standby state to switch to the Main Menu. Step 2 Click [Setting].
IP Video Phone Configuring VP-2009(P) Elite Parameter Description --User Name Account name that is specified by the VoIP service provider. The value is similar to a phone number or is a phone number. --Password Password corresponding to Register Name. The value is provided by the service provider. --Server IP address or domain name of the SIP server that is specified by the VoIP service provider. --Port Port number of the SIP server. The default value of VP-2009(P) Elite is 5060.
IP Video Phone Configuring VP-2009(P) Elite Table 5-2 Parameters about the Network Parameter Description DHCP If you select the DHCP check box, VP-2009(P) Elite automatically attempts to connect to the DHCP server for obtaining resources such as the IP address, subnet mask, gateway, and DNS server information. PPPoE If the xDSL modem is used, you can connect VP-2009(P) Elite to the network in PPPoE mode. For details about the user name and password, contact the network service provider.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-3 Desktop setting Wallpaper Manager User can manage the wall paper, such as: Preview, Delete and import. To manage the wall paper on the LCD, proceed as follows: Step 1 Access the Settings page. Step 2 Click [Display]. Step 3 Click the . Step 4 Click the , , or . Only within the limits of authority can users delete the uploading pictures.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-4 Date and time Table 5-3 Parameters about the Date and Time Parameter Description Time Zone Local time zone. Time Format To set the displayed time format of your phone, 12-hour and 24-hour respectively. NTP Mode Whether to activate the NTP mode. If choose enable, VP-2009(P) Elite automatically obtains the Universal Time Coordinated (UTC) time from a dedicated NTP server. --Time Server IP address of the NTP server that provides the UTC time.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-5 Tones and volume Manager the Ringtone Users can make operations including the audition, deletion and import of the ringtone documents, proceed as follows: Step 1 Access the Settings page. Step 2 Click [Sound]. Step 3 Click the . Step 4 Ringtones can be auditioned or deleted. Ringtone operation can also be conducted by importing through USB Step 5 Click the to return to the previous menu.
IP Video Phone Configuring VP-2009(P) Elite The phone will ring when the cursor moves to whichever a ringtone document for your convenience. Only within the limits of authority can users delete the uploading ringtones. You can consult your system administrator for more details regarding the allocation of the limits of authority. Figure 5-6 Ringtone manager Setting the password Users can change the default password of the administrator, proceed as follows: Step 1 Access the Settings page.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-7 Admin password Set the Language To configure the Language on the LCD, proceed as follows: Step 1 Access the Settings page. Step 2 Click [Personalize] Step 3 Select a required language and click the . Step 4 The phone will pop up a warning frame. Step 5 Click the icon to confirm the operation and the phone will reboot.
IP Video Phone Configuring VP-2009(P) Elite Reset to the factory When there is something wrong or irrational with certain functional configuration of the phone, you can choose the factory reset to resume the initial configuration. To reset to the factory, proceed as follows: Step 1 Access the Settings page. Step 2 Click the . Step 3 Click [Reset]. Step 4 Input the administrator password, and then click the icon Step 5 A dialog will be popped up to check whether to reset the phone.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-10 Reboot Screen Calibration To Screen Calibration, proceed as follows: Step 1 Access the Settings page. Step 2 Click [Calibration]. Step 3 A dialog will be popped up to check whether to begin the calibration.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-11 Screen calibration Call Feature Users can configure the call function through the option interface. The functions can be configured are as followed: DSS key, Picture Dial, Voice Mail, Hotline, Forward, Call Waiting, Auto Answer, Video, TV output, Key As Send and Anonymous Call. To access the Call Feature page, proceed as follows: Step 1 Press the Left/Right navigation key in the standby state to switch to the Main Menu. Step 2 Click [Call Feature].
IP Video Phone Configuring VP-2009(P) Elite DSS Key VP-2009(P) Elite provides Direct Station Selection (DSS) keys. You can assign various functions to DSS keys for using these functions quickly. Each DSS key can support 4 functions: line, speed dial, BLF, BLF list. When you set DSS Key as Speed dial, BLF and BLF List function, the DSS Key will turn green or other color. For example: When you set the DSS Key as Speed Dial, the DSS Key will turn green.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-14 DSS key setting Table 5-4 The parameter specification chart of each option Parameter Description DSS Key 0X To display the serial number of the DSS Key. Type To choose what function the required DSS key to be set. The default type is “N/A”, namely no function set. Line To choose which line the function applies to. Label User-defined name displayed in the DSS Key interface. Value To input the corresponding configuration value, e.g.
IP Video Phone Configuring VP-2009(P) Elite BLF To set the DSS Key as BLF, proceed as follows: Step 1 Click the “Type” option, and then choose “BLF” option in the pull-down menu; Step 2 Choose the line to be configured in the pull-down menu of the “Line” option. If you choose “Auto”, the default account at present is adopted; Step 3 Input the “Label”. Step 4 Input the monitor number to be configured in the “Value” field. Step 5 Input the feature code in the “Extension” field.
IP Video Phone Configuring VP-2009(P) Elite Table 5-5 The parameter specification chart of each option Parameter Description Display Name User-defined name displayed below the picture. Account To set the applicative account. If you choose “Auto”, the default account at present is adopted. Phone Number To set the automatically calling-out phone number Contact Picture Box To choose the applicative picture. Users also can upload pictures through auto provision.
IP Video Phone Configuring VP-2009(P) Elite Step 2 Click [Hotline]. Step 3 Enter the hot line number and set hot line delay. Step 4 Click the . Figure 5-17 Hotline Forward VP-2009(P) Elite supports three call forward modes: Always Forward, Busy Forward, and No Answer Forward. If auto-forwarding is under no requirement, you can forward your call to a third party through manual operation. To configure the call forward function, proceed as follows: Step 1 Access the Call Feature page.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-18 Forward setting If you enable the automatic forwarding function, the VP-2009(P) Elite automatically forwards incoming calls based on the preset forward type. If you enable the manual forwarding function, you can forward an incoming call by clicking and entering the forward-to number. Call Waiting When you are in a conversation and a new call comes, you can make the new call wait.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-19 Call waiting Auto Answer Users can answer calls automatically through the set type of Auto Answer. It supports 4 types: Directly, After 5 seconds, after 15 seconds, and After 30 seconds. The phone supports the individual configuration of each distinct account. To configure the auto answer function, proceed as follows: Step 1 Access the Call Feature page. Step 2 Click [Auto Answer].
IP Video Phone Configuring VP-2009(P) Elite Figure 5-20 Auto answer Video Users can set the call type through this option, e.g. the default call type is video call or voice call, and whether the Local Video is enabled. The settings include the Bandwidth and Frame Rate. The phone supports the individual configuration of each distinct account. To configure video, proceed as follows: Step 1 Access the Call Feature page. Step 2 Click [Video].
IP Video Phone Configuring VP-2009(P) Elite TV Output The phone supports the TV output of videos. Users can set the formats of this option through auto or manual operation. To configure the TV output function, proceed as follows: Step 1 Access the Call Feature page. Step 2 Click [TV Output]. Step 3 Choose Auto or Manual in the pull-down menu of TV Output; Step 4 Choose the formats in the pull-down menu of TV Format; Step 5 Click the .
IP Video Phone Configuring VP-2009(P) Elite Figure 5-22 Key as send Anonymous Call If Anonymous Call is enabled, the phone of the opposite side cannot display your name when you make a phone call. You can also enable the Anonymous Call Rejection. When an anonymous call is coming, the phone will automatically reject it. The function can also be set through the server, which only requires the on/off feature code.
IP Video Phone Configuring VP-2009(P) Elite Figure 5-23 Anonymous call Directory Address books on VP-2009(P) Elite stores contact information. You can add, edit, delete, call, or search for contacts. You can also add, edit or delete the contacts group. To access the Directory page, proceed as follows: Step 1 Press the Left/Right navigation key in the standby state to switch to the Main Menu. Step 2 Click [Directory].
IP Video Phone Configuring VP-2009(P) Elite Black List and Anonymous defaulted by the system can only be operated the ringtone change without being conducted the operation of deleting and renaming. Adding a Contact To add a contact, proceed as follows: Step 1 Access the Directory page. Step 2 Click [Options]. Step 3 Click [Add] in the extensional menu to enter the New Contact page.
IP Video Phone Configuring VP-2009(P) Elite The “Clear” operation is defaulted to clear all the contacts in the chosen group. If “All” is chosen to clear the group, then all the contacts on the phone (including Black List) will be cleared. Adding/Deleting/Clearing a Blacklist When the black list is recorded, the call from the contact is not accessible to your phone. Adding/Deleting/Clearing the Black List is primarily the same with Adding/Deleting/Clearing the Directory.
IP Video Phone Step 2 Configuring VP-2009(P) Elite Click [Call History]. To choose the Call History Type page, proceed as follows: Step 1 Enter into the Call History page, Press the Left/Right navigation key to switch the type. To choose the Call History Record page, proceed as follows: Step 1 Enter into the Call History Type page, Press the Up/Down navigation key to select the record. Deleting the history record To Deleting a history record, proceed as follows: Step 1 Access the Call History page.
IP Video Phone Configuring VP-2009(P) Elite Step 3 Click [Play], the phone will Automatic play the video, you can press any key to exit. Step 4 Click [Manager] enter into the manager page. You can preview, delete and enter into the USB device to import the video. To do the delete operation must have enough permission. Please consult your system administrator for more information about permission. Contact Picture To access the Contact Picture page, proceed as follows: Step 1 Access the Media page.
IP Video Phone Configuring VP-2009(P) Elite Table 5-6 Parameters about the IP Camera Parameter Description Basic The basic parameters Settings. --Device Model To select the device model --Display Name To set the display name which you want to display. --Phone Number To input the phone number of IP Camera. For more information you can consult your system administrator. --Account To set the applicative account. Advance The advanced parameters Settings.
IP Video Phone Configuring VP-2009(P) Elite Parameter Description Phone Number To input the phone number of Door Phone. For more information you can consult your system administrator. Unlock Pin To set the password corresponding to the Door Phone. If the door phone has been set a password, when you want to open the door, you must input the password at first. For more information you can consult your system administrator.
IP Video Phone 6 Configuration Using the Web Browser Configuration Using the Web Browser Establishing a Configuration Environment Before accessing the Web configuration page, proceed as follows to establish a configuration environment and obtain VP-2009(P) Elite 's IP address. Prepare a PC that meets the following requirements: Installs Ethernet adapters and supports TCP/IP. Runs the Window 98 or later operating system. Installs a Web browser such as Microsoft Internet Explorer 6.
IP Video Phone Configuration Using the Web Browser Account: configures account registration or deregistration, voice, video parameters and some advanced features.Network: includes Internet Port (WAN) and advanced settings. Phone: includes basic settings (such as date and time) and feature settings. Contacts: configures information about local phonebook, remote phonebooks and LDAP.
IP Video Phone Configuration Using the Web Browser Account Tab Page Account On the Account tab page, you can configure information for a VP-2009(P) Elite's account such as registration and deregistration, as shown in Figure 6-3: Figure 6-3 Account tab page Table 6-2 Parameters on the Account tab page Parameter Description Register Status Status of the account that you select. The options are Registered, Disabled, Unknown, and Register Fail. Account Active Whether to activate the account.
IP Video Phone Configuration Using the Web Browser Parameter Description Password Password corresponding to Register Name. The value is provided by the service provider. SIP Server SIP server's IP address or domain name, which is provided by the VoIP service provider. Port Port number of the SIP server. The default value of VP-2009(P) Elite is 5060. Enable Outbound Proxy Server Whether to enable the outbound proxy server.
IP Video Phone Configuration Using the Web Browser Voice Figure 6-4 Voice codecs page Table 6-3 Parameters on the Voice tab page Parameter Description Disable codecs Disabled voice coding types. VP-2009(P) Elite supports the following coding types: PCMU, PCMA, G.723, G.729, G.722, GSM, AACLC and iLBC. Enable codecs Enabled voice coding types. The types are listed in descending order of priority.
IP Video Phone Configuration Using the Web Browser Video Figure 6-5 Video codecs page Table 6-4 Parameters on the Video tab page Parameter Description Disable codecs Disabled video coding types. VP-2009(P) Elite supports the following coding types: H264, H263 and mp4v-es. Enable codecs Enabled video coding types. The types are listed in descending order of priority. Bandwidth Select the bandwidth. Frame Rate Select the bandwidth. Frame Rate。 I-Frame Refresh (s) Set the refresh time.
IP Video Phone Configuration Using the Web Browser Advanced Figure 6-6 Account advanced page Table 6-5 Parameters on the Advanced tab page Parameter Description UDP Keep-alive Message Whether to send a UDP message at an interval to keep a port always available. UDP Keep-alive Interval Interval for sending UDP messages. For example, 30 seconds. RPort Port through which the server sends a response to VP-2009(P) Elite. Details about this parameter are specified in RFC 3581.
IP Video Phone Configuration Using the Web Browser Parameter Description SIP Session Timer T1 Round trip time (RTT) between the server and the client. If the network latency is long, set it to a greater value. Details about RTT are specified in RFC 3261. Default value: 0.5 SIP Session Timer T2 Interval between the INVITE response receiving and the non-INVITE request sending, in seconds. Details about this parameter are specified in RFC 3261.
IP Video Phone Configuration Using the Web Browser Parameter Description SRTP Whether to enable or disable Secure Real-time Transport Protocol BLF List URL To input the BLF list server’s URL BLF List Code To input the BLF list feature code. BLF Subscribe Period(seconds) Validity period for the BLF subscription time. SIP Server Type Select the SIP server type. Caller ID Header The options are FROM, PAI, PAI-FROM, RPID-PAI-FROM, PAI-RPID-FROM and RPID-FROM.
IP Video Phone Configuration Using the Web Browser Table 6-6 Parameters on the Internet Port (WAN) tab page Parameter Description DHCP If you select the DHCP check box, VP-2009(P) Elite automatically attempts to connect to the DHCP server for obtaining resources such as the IP address, subnet mask, gateway, and DNS server information.
IP Video Phone Configuration Using the Web Browser --VLAN The value Enabled indicates that the VLAN function is enabled for the Internet port. --VID ID of the VLAN where the IP phone belongs to. The network administrator divides the network where the switch resides into multiple VLANs. Each VLAN has a unique ID. --USRPRIORITY VLAN priority for the Internet port. The value ranges from 0 to 7. -- Voice QoS Voice QoS. Value range: 0 to 63 -- SIP QoS Signaling QoS.
IP Video Phone Configuration Using the Web Browser Secondary NTP Server IP address of the secondary NTP server that provides the UTC time. Update Interval Interval at which VP-2009(P) Elite obtains the UTC time from the NTP server. Main Desktop Option Choose the idle status If you did not press any digit key on the dial-up status, the phone will turn to which one. (Include DSS Key Desktop、Wallpaper Desktop、 Menu Desktop and Picture Dial Desktop). If you choose Auto, the default is Wallpaper Desktop.
IP Video Phone Configuration Using the Web Browser Forward Configures the call forward function. Call forward types include Always, Busy, and No Answer. Always Forward Whether to always enable the call forwarding function. If you select On, VP-2009(P) Elite forwards all incoming calls to a preset number. Target Number that incoming calls are forwarded to. Busy Forward Whether to enable the busy forwarding function.
IP Video Phone Configuration Using the Web Browser Figure 6-11 DSS key Table 6-10 Parameters on the DSS Key tab page Parameter Description Key Choose which DSS key to assign the function. Type Function that you assign to a memory key. There are 4 kinds. For more information about the function, please refer to Table 6-11. Line Account that you configure a function for. Label Self-defined function name, which is displayed next to the corresponding DSS key on VP-2009(P) Elite.
IP Video Phone Configuration Using the Web Browser Speed Dial Functions as the speed dial key. Select Auto or Line 1 to Line 4. Self-defined function name Enter the speed dial number. This parameter is dimmed. BLF Listens on a number. When the BLF function is enabled, you can know the real-time status of the listened on number, such as idle, ringing, or talking. Select Auto or Line 1 to Line 4. Self-defined function name Enter the number to be listened on. Enter a function code.
IP Video Phone Configuration Using the Web Browser Figure 6-12 Replace rule Dial-now rule: After you enable this rule, VP-2009(P) Elite makes a call as soon as you enter the preset number. For example, if you set Dial-now Rule to 0147, VP-2009(P) Elite makes a call to 0147 for the setting time after you enter 0147. The setting time is the value which you input in the “Dialnow Delay time (0~2000ms)” field. The phone supports this rule of each distinct account.
IP Video Phone Configuration Using the Web Browser Figure 6-13 Dial-now rule Door Phone Figure 6-14 Door phone - 58 -
IP Video Phone Configuration Using the Web Browser Table 6-12 Parameters on the Door Phone tab page Parameter Description Door Phone List Select a Door Phone which you want to configure in this list. Device Model Select the device model Display Name Set the display name which you want to display. Phone Number To input the phone number of Door Phone. For more information you can consult your system administrator. Unlock PIN Set the password depends on Door Phone.
IP Video Phone Configuration Using the Web Browser Access PIN To input the PIN depends on IP Camera. For more information you can consult your system administrator. If the IP Camera hasn’t been set a PIN, user can see the video directly. If the phone has been set a PIN, user must input the PIN at first. Full Screen Choose whether to play full screen. Not Send Video Choose whether to send the audio during the IP Camera conversation.
IP Video Phone Configuration Using the Web Browser Remote PhoneBook Each VP-2009(P) Elite is configured with a local address book. A public address book is required for all phones in an enterprise. After a remote address book is enabled, users can access the remote address book. Set the URL and name for each remote address book, as shown in Figure 6-17 Figure 6-17 Remote PhoneBook LDAP The LDAP address book provides the following functions: Searches for contacts.
IP Video Phone Configuration Using the Web Browser Figure 6-18 LDAP page Table 6-14 Parameters on the LDAP tab page Parameter Description LDAP Whether to enable or disable LDAP. LDAP Name To input the LDAP name. LDAP Name Filter Name filter. After you enter a name, the IP phone uses the name filter to search the LDAP server for the contact. The settings for the name filter must be based on RFC 2254. The entered names will replace % in the name filter.
IP Video Phone Configuration Using the Web Browser Server Address IP address or domain name of the LDAP server. Examples are as follows: 192.168.1.100 lday.company.com Port Port number of the LDAP server. Default value: 389 Base Root directory that the IP phone searches. For example, if the value is dc=Redmond, dc=wa, the root directory is wa\Redmond. User Name User name for logging in to the LDAP server. The user name is set by the LDAP server administrator.
IP Video Phone Configuration Using the Web Browser Protocol Version Protocol version. The options are Version2 and Version3. The protocol version selected on the IP phone must be the same as the parameter setting. LDAP Lookup For Incoming Call The value Enabled indicates that the IP phone searches the LDAP server for the calling number and displays the calling party's name on the LCD. The value Disabled indicates that the IP phone does not search the LDAP server for the calling number.
IP Video Phone Configuration Using the Web Browser Figure 6-20 Upgrade advanced page Table 6-15 Parameters on the Advanced tab page Parameter Description PNP Active Whether to enable or disable PNP. PNP(Plug and Play) provides a proprietary method to enable "Auto Provisioning". DHCP Active Whether to enable or disable DHCP. Custom Option(128~254) A valid Custom Option is from 128 to 254. The Custom Option Type must be in accordance with the one defined in the DHCP server.
IP Video Phone Configuration Using the Web Browser Power On Whether to enable or disable auto provision once the phone is power on. Repeatedly Whether to enable or disable auto provision with the interval configured. Interval(Minutes) Set the interval time. Weekly Whether to enable or disable auto provision in the configured period. Time Configure the period. Day of week Select the day in the week. Autoprovision Now Whether to upgrade at once.
IP Video Phone Configuration Using the Web Browser Trusted Certificates To upload a trusted certificate, proceed as follows: Step 1 Click Browse in the Trusted Certificates area and select a trusted certificate in the dialog box that is displayed. Step 2 Click Upload. Step 3 Choose enable or disable this function in the “Only Accept Trusted Certificates”. If Enabled is selected, the imported root certification is used to authenticate the signature in the server certificate.
IP Video Phone Configuration Using the Web Browser Figure 6-23 Server certificates Saving Settings Click the Submit button on the lower-part of a page after setting is completed.
IP Video Phone 7 Using VP-2009(P) Elite Using VP-2009(P) Elite Overview Call Type VP-2009(P) Elite supports audio and video calls. Audio calls: during the conversation, you can only hear the sound of the other party. Video calls: during the conversation, you can not only hear the sound of the other party, but you other. User can press can also see each to enable or disable the local video. Answer Mode VP-2009(P) Elite supports the following answer modes: handset, hands-free, and headset.
IP Video Phone Using VP-2009(P) Elite Redialing If you redial a number, VP-2009(P) Elite uses the account that is used to dial the same number the previous time. Step 1 Press key to enter into the Call History page. Step 2 Select a record and then press key again to send. Using the Call History to Make a Call VP-2009(P) Elite provides a key for users to obtain the call record list. To using the call record list to make a call, proceed as follows: Step 1 Enter into the Call History page.
IP Video Phone Using VP-2009(P) Elite Answering a Call Answering a Single Call In the standby mode, VP-2009(P) Elite receives an incoming call and starts ringing. To answer the call, pick up the handset, press the key or click . Answering Multiple Calls Step 1 In the standby mode, VP-2009(P) Elite receives an incoming call and starts ringing. Step 2 You pick up the handset, press the key, or click Step 3 VP-2009(P) Elite receives another incoming call and pop up a box.
IP Video Phone Using VP-2009(P) Elite indicating transfer failure is displayed on the user A's phone screen. After pressing the key, user A resumes the call with user B. Semi-attend transfer Click the key. User A hears the RBT. When user C's phone rings, user A presses the key. After user C picks up the phone, user A hangs up the phone to complete the transfer. Attend transfer Press the key. User A hears the RBT and user C's phone is ringing.
IP Video Phone Using VP-2009(P) Elite Table 7-2 Status on DSS Key menu Status Description The listened-on account is in the idle. The listened-on account is in the talking state or in the dial status or in the ringing state BLF List BLF List is a function which uses a group of programmable keys to subscribe to server for the state of each account in some group.
IP Video Phone 8 Maintaining VP-2009(P) Elite Maintaining VP-2009(P) Elite Restarting VP-2009(P) Elite Users can restart the phone via phone or web interface. Restart the phone via phone interface, please refer to “Reboot”. Restart the phone via web interface, please refer to “Basic setting” on the Upgrade page. Resetting VP-2009(P) Elite Users can reset the phone to factory setting via phone or web interface. Reset the phone via phone interface, please refer to “Reset to the factory”.
IP Video Phone Maintaining VP-2009(P) Elite The manual is only for reference, please take the object as the standard. We reserve the right to improve or change the product and the user guide without notice.
