owner’s manual 2013 yeti 575 YETI CYCLES 600 Corporate Circle, Unit D Golden, CO 80401 888.576.9384 www.yeticycles.
Table of Contents Brand Overview 06 Frame Features 08 Geometery 10 Maintenance Schedule 12 setup overview 14 Shock Setup 15 Quick start guide 16 Cable/Line Setup 18 technical Assembly Overview 20 chip system 24 Exploded Views 26 REBUILD KITS 28 legal 4. Warranty 30 Contact Information 31 5.
Welcome to the tribe. Congratulations on your purchase of a new Yeti. We are confident your new bicycle will exceed your expectations for value, performance, and ride quality. Each frameset and component has been custom specified and designed to enhance your riding experience. Whether you are a beginner cyclist, or a seasoned pro, your Yeti bicycle will provide endless hours of two-wheeled fun. This manual outlines basic setup and maintenance recommendations of your new Yeti.
the 575 is the original all mountain rig. 8. 1. yeti pure tubing 2. iscg 03’ tabs 3. hydroformed rear triangle 4. Tapered Inset HeadTube (44mm/56mm) 5. rear shock by fox racing shox 6. Dropouts 12mm x 142 thru axle or 135mm QR 7. Cable stops for height adjustable seatpost 8. Direct Mount front derailleur 1. Yeti pure tubing is custom butted and tapered 7005 aluminum. This makes the frame lightweight and strong without the use of gussets.
Geometry fox 32 150 mm fork B I A J D C K E G F XS SM MD LG XL A 16.0 17.5 18.5 20.5 20.5 B 21.8 22.8 23.8 24.8 25.8 C 68.0 68.0 68.0 68.0 68.0 D 72.8 72.8 72.8 72.8 72.8 E 16.9 16.9 16.9 16.9 16.9 F 42.4 43.5 44.5 45.6 46.4 G 13.3 13.3 13.3 13.3 13.3 H 28.5 29.1 29.1 29.1 29.1 I 4.1 4.9 4.9 5.1 5.1 J 20.5 20.5 20.5 20.5 20.5 K 1.5 1.5 1.5 1.5 1.5 fox 34 150 mm fork xs SM MD LG XL A 16.0 17.5 18.5 20.5 20.5 B 21.
keep your new yeti fresh and clean schedule Clean and lube chain Check tire pressure Clean bike of mud and debris ANNUALLY Yeti strongly recommends using a torque wrench when assembling your frame. Torque specifications for individual parts on the 575 are listed below, as well as in the step by step assembly instructions later in the manual. For general bicycle maintenance please consult the torque specifications of the manufacture’s component you are adjusting.
Shock Setup yeti tips tools needed Inspect your shock for any visible damage. If oil is leaking or you notice any damage to the surfaces or seals, please contact the Fox Racing Shox service center for repair at 800. FOX.SHOX. • Shock Pump • Tape Measue Shock set-up can fluctuate greatly based on the rider. The set-up guide is intended as a base line to get the rider started. Experiment with your settings to find the set-up that works best for you. 01. Air pressure 02.
shock setup 04. compression damping 05. trail adjust The compression dampening has three levels of adjustment and is controlled by the blue lever on the shock. The “climb” mode engages the firmest low-speed compression setting for maximum pedaling efficiency. The “trail” mode engages a moderate low-speed compression setting for an optimal blend of pedaling efficiency and bike control, on various riding terrain.
cable Setup yeti tips The 575 has full cable housing. By using full cable housing, we have eliminated break points in the line of your shifter housing. This allows riders to experience better overall shifting performance by reducing the entrance of unwanted elements such as sweat and sediment. Use of full cable housing helps prevent corrosion from the elements and keeps the shifting smoother for a longer period of time.
Assembly yeti tips tools needed Make sure your tools are in good condition. A worn allen key can round the hex on a bolt not allowing for proper torque. • Dead blow hammer • Two - 5mm allen keys • Two - 4mm allen keys • 3mm allen key • Guide pin tool • Grease • Blue loctite • Purple loctite Torque settings are listed throughout the instructions. It is also import to prep all bolt threads. The instructions denote whether to use a Loctite compound or grease.
assembly assembly 05. 06. 09. 10. Align the shock and dogbone. Orient the lower portion of the shock between the lower bearings on the dogbone. If necessary, loosen the pinch bolts on the dogbone to allow the bearings to move and accommodate the shock. Slide the swingarm over the main pivot bore, using the grooves in the swingarm to properly align over the bore. Prep an M6x1x12mm male Ti bolt with blue loctite and install into the 57.5mm Ti stud.
chip system 01. 02. Use a 2.5mm allen key to loosen the two M4x9mm flat head bolts holding the QR insert derailleur hanger in place. Remove the bolts and the QR insert from the frame. Repeat the process for the bolts and the non drive QR insert. Fit the 12MM insert hanger into the groove on the inside of the drive side chainstay. The hanger should be flush with the chainstay. Next, insert the 12mm drive cap through the chainstay and into the hanger from the outside of the drive side chainstay.
Exploded Views 1 10 1 7 10 4 3 4 6 6 4 7 4 11 10 4 9 4 8 9 11 9 5 7 2 5 10 9 26. part # description qty na 575 FRONT TRIANGLE 1 2 na 575 SWINGARM 1 3 300040235 575 DOGBONE 1 4 300020032 BEARING 398 2RS MAX DOUBLE ROW 6 5 300020030 BEARING 3903 2RS MAX 2 6 300030194 BOLT CAP SCKT HD M4X.7X10 2 7 300030139 BOLT FLAT HD M4X.7X16 3 8 300030191 STUD-TI-FEMALE 8X57.5MM 1 9 300030069 WASHER 8.5X12.5X0.5 MM 4 10 300030062 WASHER 6.5X12.5X0.
Rebuild Kits part # description qty HNA0575M00AA00MST0000 575 MASTER REBUILD KIT 1 300020020 GARLOCK DP BUSHING .5”X.5” 2 300020030 BEARING 3903 2RS DOUBLE ROW 2 300020032 BEARING 398 2RS MAX DBL ROW 6 300030062 WASHER 6.5x12.5x0.5 mm 4 300030069 WASHER 8.5x12.5x0.5 mm 4 300030110 BOLT-TI-MALE M6X1 12MM 2 300030139 BOLT FLAT HD M4X7X16 3 300030188 PIVOT PIN 17X7.5/10X1THRD 52.4 1 300030189 PIVOT PIN BOLT M10 X 1 X 22 1 300030191 STUD-TI-FEMALE 8X57.
Warranty Yeti Limited (1) One Year Frame Warranty (applies to 303 WC / 4X / DJ) Yeti Cycles will repair or replace, at its option, any frame it determines to be defective due to defective materials and/or workmanship. The (1) one year limited warranty is conditioned upon the bicycle being ridden under normal conditions and having been properly maintained.
