instructions MP PT Solar charge controller, which has the Max Power Post Target Function, Is suitable to be used in the battery or batteries pack solar energy charging and load charging control. Its suitable for off-grid solar energy system with wide vantage. MP PT Solar Charge Controller, combine the most advance charging technology with high-efficiency and professionalization maintenance technology, has numerous programming options, perfect protection function and Intuitive LCD display.
*24V system: Only suitable far series of ternary lithium batteries, nominal voltage of the battery 22.2v; Only suitable for 8 series of lithium Iron phosphate batteries, Le. nominal voltage of the battery 25.6v *48V system:Only suitable for 12 series of ternary lithium batteries, nominal voltage of the battery 44.4v; Only suitable for 16 series of lithium Iran phosphate batteries, Le. nominal voltage of the battery 51.
core of the conductor Into the terminal, and use a screwdriver to screw down the connecting screw clockwise. 4) Pull out the lead wire to confirm that the screw presses the copper wire. Verify again that the load output ls off. 5) Connect the either end of the wire to the load {red ine "+ back line"). After the load connection s completed, and the check ks correct, press tha down kay on the controller totem on the load and the load is powered on.
LCD Display 1)DaytimeMode 2}Solar Panel 3)Battery Power Display load Unities &|Digital Display Symbolization 8)Battery System Voltage 1)Daytime mode 2)Night Mode 3)Solar Panel 4)Battery powerlessness ~~ somersetting 6)Load T)Unit prestidigitation ~~ 9)Battery Symbol 10)Battery System Voltage 2 1) Battery 2) Solar panel 3) Load 4) Undercurrent 5) Voltage 6 Light contra 7) Operation made selection 8) Light control delay 9) Universal control 10) Operation mode selection 11) Illegal operation 12) Timeserving 13
Controller Interface Indicate 10A-20A Setting Menu Interface 10A-20A Interface/ Parameter Setting 1. Home page 2. Environment temperature 3. Charging current 4. Discharge current 5. Floating charge voltage 6. Recovery voltage phototypesetting) 7. Load switch(adjustment) 9. Battery type Light control delay Parameter setting method MENU DOWN 1. Floating charge voltage: ring est menu key to select the mode, and the screen will display the Interface shown In Figure (5).
30A-40A Setting Menu Interface Parameter setting method MENU up DOWN 1. Floating charge voltage setting: press the many key to select the mode, and the screen will display the Interface shown in Figure (2). Long press for 5 seconds, the screen will lash, and press the up and down buttons to set the floating charge voltage. Press the menu key 30A-40A Interface/ Parameter Setting 1, Home page 2. Floating charge voltage setting(adjustment} 3. Recovery voltage phototypesetting) 4. Load switch(adjustment} 5.
50A-60A Setting Menu Interface Parameter setting method . 25” MENU up DOWN 1. Floating charge voltage setting: press the many key to select the mode, and the screen wil display the Interface shown In Figure( 2). 3 Long press for 5 seconds, the screen will flash, and press the up and TT down buttons to set the floating charge voltage. Press the menu key to Fy confirm. 2. Recovery voltage setting: refers to charging according tithe voltage 2 the customer wants to charge, Press the menu key to select the mode.
80A Setting Menu Interface Parameter setting method |m|= 0.0. 1230. 1230. MENU up DOWN = 2 24.5" 1,Battery type setting: long press the menu key for about 3 seconds, 0: |e |x 0.0.77 and the screen flickers to the figure (3) interface. Press the up key to 30. 1230. select the battery type (B: lead clad battery, L1: lithium ternary 5) @ Battery, L2: lithium Iron phosphate battery), and the battery type will = 13.0" stay for about 3 seconds to automatically determine and return to the 0.0. main Interface.