Installation Instructions

FCC RF EXPOSURE INFORMATION:
WARNING!! Read this information before using your Smart Terminals
In August 1986 the Federal Communications Commission (FCC) of
the United States with its action in Report and Outer FCC 96-326
adopted an updated safety standard for human exposure to radio
frequency (RF) electromagnetic energy emitted by FCC regulated
transmitters. Those guidelines are consistent with the safety standard
previously set by both U.S. and international standards bodies. The
design of this Smart Terminals complies with the FCC guidelines and
these international standards. Use only the supplied or an approved
antenna. Unauthorized antennas modifications, or attachments could
impair call quality, damage the Smart Terminals, or result in violation of
FCC regulations. Do not use the Smart Terminals with a damaged
antenna. If a damaged antenna comes into contact with the skin, a
minor burn may result. Please contact your local dealer for
replacement antenna.
NORMAL POSITION:
Hold the phone as you would any other telephone with the antenna
pointed up and over your shoulder.
RF Exposure Information:
This product is compliance to FCC RF Exposure requirements and
refers to FCC website https://apps.fcc.gov/oetcf/eas/reports/
GenericSearch.cfm search for FCC ID: 2A2UU-L200 to gain further
information include SAR Values.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits aredesigned to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This device is acting as slave and operating in the 2.4 GHz (2412 ~
2462 MHz) band. Ad Hoc function is supported but not able to
operate on non-US frequencies.
All transmission frequencies of U-NII-1,U-NII-2A and U-NII-3 comply
with 47 CFR FCC Part15.407(g) and the manufacturer declares that
their transmission is maintained within the U-NII-1, U-NII-2A and U-NII-3
bands.
BODY-WORN OPERATION:
This device was tested for typical body-worn operations with the
back/front of the phone kept 10mm from the body. To comply with
FCC RF exposure requirements, a minimum separation distance of
10mm must be maintained between the user's body and the back/
front of the phone, including the antenna.
Third-party belt-clips, holsters and similar accessories containing
metallic components shall not be used.
Body-worn accessories that cannot maintain 10mm separation
distance between the user’s body and the back/front of the phone,
and have not been tested for typical body-worn operations may not
comply with FCC RF exposure limits and should be avoided.
For more information about RF exposure, please visit the FCC website
at www.fcc.gov
Your Smart Terminals is a low power radio transmitter and receiver.
When it is ON, it receives and also sends out radio frequency (RF)
signals. In August, 1996, the Federal Communications Commissions
(FCC) adopted RF exposure guidelines with safety levels for hand-held
wireless Smart Terminals. Those guidelines are consistent with the safety
standards previously set by both U.S. and international standards
bodies:
<ANSIC95.1> (1992) / <NCRP Report 86> (1986) / <ICNIRP> (1999)
Those standards were based on comprehensive and periodic
evaluations of the relevant scientific literature. For example, over 120
scientists, engineers, and physicians from universities, government
health agencies, and industry reviewed the available body of
research to develop the ANSI Standard (C95.1). Nevertheless, we
recommend that you use a hands-free kit with your Smart Terminals
(such as an earpiece or headset) to avoid potential exposure to RF
energy. The design of your Smart Terminals complies with the FCC
guidelines (and those standards).
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could
damage the phone and may violate FCC regulations.
-Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.