User Manual

Regulation Conformity of the Wireless Module:
FCC Approval (Part 15C)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference a
t his own expense.
Co-located:
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
RF Exposure Compliance:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines.
This equipment should be installed and operated keeping the radiator at least 20cm or more
away from person’s body.
IC Approval (RSS-210, RSS-102)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
(RSS-102)
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure
rules. This equipment should be installed and operated keeping the radiator at least 20cm or
more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
Cet équipement est conforme aux limites d’exposition aux rayonnements
énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en
gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception
des extrémités : mains, poignets, pieds et chevilles).
EMC Conformity Standards:
EN61326-1 Class A, Table 2 (For use in industrial locations), EN55011 Class A,
Group 1, EN61000-6-2
CAUTION
This instrument is a Class A product, and it is designed for use in the industrial environment.
Please use this instrument in the industrial environment only.
Safety Requirements:
EN61010-1, CSA C22.2 No.61010-1
(1) Pollution Degree 2
"Pollution degree" describes the degree to which a solid, liquid, or gas which deteriorates
dielectric strength or surface resistivity is adhering. " 2 " applies to normal indoor atmosphere.
Normally, only non-conductive pollution occurs. Occasionally, however, temporary conductivity
caused by condensation must be expected.
(2) Installation Category I
"Overvoltage category (Installation category)" describes a number which defines a transient
overvoltage condition. It implies the regulation for impulse with stand voltage. " I " applies to
electrical equipment which is supplied from the circuit when appropriate transient overvoltage
control means (interfaces) are provided.
Degrees of Protection:
Waterproof and dustproof function works while in the mated state of connector.
IP66, NEMA Type 4X
Explosion-Proof Types:
TIIS, FM, ATEX, CSA, IECEx (approvals under pending)
5.3 Model and Suffix Codes
Refer to General Specification “GS 01W03B01-01EN”.
5.4 External Dimensions and Pin Assignment
Units: mm
123
45
Pin Signal
1NotConnected
2Ground
3PowerSupply
4Data+
5Data-
Revision Record
Title: FN110 Field Wireless Communication Module
Manual No.: IM 01W03B01-01EN
Edition Date Page Revised item
1st Mar.2014 ― New Publication.