Instruction Manual

6-2
<Toc> <Ind> <6. Functions and Usage of D Registers >
IM 77J04J11-01E 1st Edition : 2006.08.25-00
6.3 D Register Map Table
*1: User area applies when a graphic panel manufactured by Digital Corp. is used.
: The number of writing actions is limited to 100,000.
D-Reg No.
D0001
D0002
D0003
D0004
D0005 to D0100
D0101
D0102
D0103
D0104
D0105
D0106
D0107
D0108
D0109
D0110
D0111
D0112
D0113
D0114
D0115
D0116
D0117 to D0200
D0201
D0202
D0203
D0204
D0205
D0206 to D0209
D0210
D0211
D0212
D0213
D0214
D0215
D0216 to D0300
D0301
D0302
D0303
D0304
D0305
D0306
D0307 to D0308
D0309
D0310
D0311
D0312
D0313 to D0400
D0401 to D0450
Ref No.
40001
40002
40003
40004
40101
40102
40103
40104
40105
40106
40107
40108
40109
40110
40111
40112
40113
40114
40115
40116
40201
40202
40203
40204
40205
40210
40211
40212
40213
40214
40215
40301
40302
40303
40304
40305
40306
40309
40310
40311
40312
40401 to 40450
H No.
0000
0001
0002
0003
0064
0065
0066
0067
0068
0069
006A
006B
006C
006D
006E
006F
0070
0071
0072
0073
00C8
00C9
00CA
00CB
00CC
00D1
00D2
00D3
00D4
00D5
00D6
012C
012D
012E
012F
0130
0131
0134
0135
0136
0137
0190 to 01C1
R/W
R
R
R
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R
R
R
R/W
Description
Status
Alarm status
Input value (display value)
Input unit
Alarm-1 setpoint (A1)
Alarm-2 setpoint (A2)
Alarm-3 setpoint (A3)
Alarm-4 setpoint (A4)
Alarm-1 action (AL1)
Alarm-2 action (AL2)
Alarm-3 action (AL3)
Alarm-4 action (AL4)
Alarm-1 hysteresis (HY1)
Alarm-2 hysteresis (HY2)
Alarm-3 hysteresis (HY3)
Alarm-4 hysteresis (HY4)
Alarm ON delay (OND)
Alarm OFF delay (OFD)
Setpoint (SP)
Keylock (LOC)
Bias (BS)
Economical mode (ECO)
Burnout action (BSL)
Wiring resistance correction (WIR)
RJC sensor (RJC)
Communication protocol (PSL)
Address number (ADR)
Baud rate (BPS)
Parity (PRI)
Stop bit (STP)
Data length (DLN)
Range code number (IN)
Maximum measured input value (RH)
Minimum measrued input value (RL)
Decimal point position of scaling value (SDP)
Maximum scaling value (SH)
Minimum scaling value (SL)
Input adjustment point LOW (BL)
Input adjustment LOW (AL)
Input adjustment point HIGH (BH)
Input adjustment HIGH (AH)
User area *1
D-Register Data Area