Installation Instructions

Setting
long press
Setting
long press
Sets sedentary time and valid time period in the app.
Display effect as shown above in dynamic type.
Display description
After connecting the app, the app needs to open the
message reminder function.
The message content is shown as above
Display description
When the message arrives, touch the button to display any
interface.
2.Open the Tikfit app bond to the equip
Smart Wristband
Instructions and warranty card
>2cm
close to the skin
Display
Touch the right button
(touch to the right)
Touch the left button
(touch the left to switch to the menu)
1.Function mode conversion operation
Mobile phone system hardware platform needs
to meet the conditions
IOS8.0 above Android 4.3 above Mobile phone hardware
support Bluetooth 4.0
Wear it properly
Scan to download
the Tikfit app
Click the “+”on the
up corner, Select
device management
Click product icon to
select automatic
binding
Open the app, register
and fill in your personal
information correctly
Turn on the bluetooth
of your phone
Bluetooth
1.APP Download Complete registration
APP download and device pairing Main features of the bracelet
Bracelet icon instructions
Basic parameters of the bracelet
Product model: CW10C
Product net weight: 25.0g
Power source: polymer lithium battery
Battery capacity: 95mAh
Synchronization mode: Bluetooth 4.0
Protection level: IP67
Product size: 250*19*12mm
Display mode: IPS LCD display
Standby time: 1 month
Charging time: about one hour
Working temperature: 5 ° C ~ 40 ° C
Executive standard: Q/EOL 002-2018
Switch menu, long
press to enter menu
USB plug
1. For the first time use, please insert the body of the wristband into the
USB interface to activate the device.
2. If the bracelet is power off, please insert the body of the bracelet into
the USB port to charge.
When the hand ring screen is switched as shown above,
the bracelet is charged.
Product activation and charging
Wrist strap installation instructions
Binding is successful,
APP jumps to the
bracelet homepage
FCC warning
Important safety instructionsNormal problems
Can't find the bracelet when pairing
1.Please make sure your phone is Bluetooth enabled and the phone
is "supported".
2.When pairing, please ensure that the distance between the
bracelet and the mobile phone is within 0.5 meters, and the
Bluetooth communication range is less than 10 meters after pairing.
3.Please check if the bracelet has power. If it is still not resolved
after charging, please contact us.
Occasionally there will be a situation where Bluetooth
cannot be connected?
1.Please make sure your phone is Bluetooth enabled and the phone
is "supported".
2.The Bluetooth service of some mobile phones occasionally has an
abnormality at startup, which causes such a situation.
3.Usually re-switch the phone Bluetooth or restart the phone, you
can establish a connection.
1.This product is not a medical device and cannot be used to
diagnose, treat, cure or prevent any disease
2.Never look at the product screen while driving, distracting, or
otherwise likely to cause danger
3.This product is not a toy. Do not let children or pets play with the
product. The product contains small Components which can cause
choking hazards
4.Product function is affected by uncertain factors such as external
interference, so the product specification is only for reference
5.Use a computer, charging treasure or power supply certified by a
recognized testing laboratory
6.Do not attempt to replace or open the case to disassemble the
product, otherwise the product warranty will be invalid. And may
bring security risks
7.Do not place this product in a fire since the battery may explode
8.Never expose this product to extremely high or low temperatures.
9.Do not use this product in saunas, steam baths or under charging.
10.Long-term wear may cause skin discomfort and allergic
symptoms in some users. If you notice any redness, swelling,
itching or other allergic symptoms on your skin, please stop and
consult a doctor
The alarm mode is not displayed on the bracelet?
1.The alarm mode function needs to be displayed after the smart
alarm is turned on in the app.
The bracelet does not receive a reminder message
1.Please make sure that the bracelet is connected to the phone.
2.Set "Ignore device / unpair" in the phone Bluetooth pairing
settings.
How to restore the factory settings
1.The bracelet has been connected to the phone. In the app, go to
"My - System Settings" and select "Restart Device"
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for aClass B digital device, pursuant to Part 15 of the FCC
Rules. These limits aredesigned to provide reasonable protection
against harmful interference in aresidential installation.
This equipment generates, uses and can radiate radiofrequency
energy and, if not installed and used in accordance with theinstruc-
tions, may cause harmful interference to radio communications.
However,there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user isencouraged to try to correct the
interference by one or more of the followingmeasures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure
requirement. The device can be used in portable exposure condition
without restriction.
FCC ID:2ANDX-CW10C
Display instructions
3.Time mode
Enter the setting mode, you can view device information, adjust
backlight, switch language and Set time
2.Set
MON
MON
Time
click the
right button
click the
left button
click the
right button
click the
left button
click the right button click the left button
click the
right button
click the
left button
The left key
confirm and
right key select
click the
right button
click the
left button
click the
right button
click the
left button
click the
right button
click the
left button
Steps MotionScreen off
state
MON
Step
Step
Sport
long press
Sport
long press
Sport
long press
Setting
Setting
Heart beat
bpm
bpm
Calorie
Kcal
Kcal
Exercise mileage
Km
Long press
3 seconds
press the right
button for 3
seconds
press the right
button for 3
seconds
The left key
confirm and
right key select
The left key
confirm and
right key select
MON
4.Alarm mode
5.Step counting mode
Step mode - number of steps
Step Mode - Sport
This mode has 4 interfaces: step interface, motion status interface,
sports mileage interface, calorie interface.
00:56:07
9.Sleep mode
km
6.Step mode - sports mileage
7.Step counting mode - calories
Exercise mode entry and exit operation instruction
8.Heart rate mode
enter sport
mode
exit sport
mode
MON
10.Sedentary reminder
12.Photo mode
11.Search for phone mode
13.message notification
Updating
14.Device upgrade mode
Please send
me a book
for me.
Have dinner
together
today?
When installing the wristband of the wristband, please look for the
corresponding wristband on both sides of the main body of the hand
ring. Press in and install it.
When wearing the bracelet, touch the button toward the inner side of
the body, the bottom case photoelectric sensor needs to be attached
Wearing and it requires the wristband to keep 2cm or more from the
wrist bone.
Time function : Display month/day/time, time is displayed in 12/24
hour mode
Step data calculating: display the number of steps in the day,
calories burned, mileage
Alarm function : Alarm in vibration mode
Sleep monitoring function
Target completion reminder function: Reminder by vibration
Caller ID and QQ, WeChat reminder
Bluetooth wireless signal transmission
Display current time, month, day, and remaining
battery status.Time can choose 12H/24H.
Display instructions
When the alarm starts, any key can stop, if it not
stop, it will alaim after 10 min for three times.
The alarm is off by default. You can set 10 groups
of alarms on the app. After synchronizing the data,
you can turn on the alarm and display the current
time of the last group of alarms.
Display instructions
Display the total number of steps for the day, it will
come to zero every day at 0 o'clock.
The sports interface displays: the current exercise
duration, number of exercise steps, exercise
mileage, calorie consumption, current heart rate
If the exercise time is less than 1 minute then it will
exits the sport mode, the motion data will not be
recorded: the crying face icon will be displayed
Operating instructions
Click the left button to switch to the time interface
and right click to switch to the motion interface.
After entering the exercise mode, the heart rate calculation
is automatically turned on, and the heart rate data is
collected in the background
Show current mileage.
The data is cleared at 00:00 every day.
Display description
Click the left button to switch to the step interface and right
button to switch to the sport mileage.
Show current calories.
The data is cleared at 00:00 every day.
Display description
The display effect is as shown on the right, and
the sleep icon is displayed in the upper left
corner of the time interface.
Display description
Open search for phone function in the app
Display description
Long press the right button will turn on the
alarm on the phone
Operation instructions
Shown as left pic
Display description
Operate on bracelet firmware to upgrade by
entering upgrade mode
Display description
It is shown as left pic.
Connect the bracelet first, open the camera
settings in the app, the camera icon appears
on the bracelet, touch the right button or shake
the device to control the phone to take photos.
Operation instructions
Manually switch to the heart rate interface and
measure the heart rate in real time. The test
time is 25s then the heart rate is automatically
turned off.
In the APP settings, turn on the automatic heart
rate measurement function. At regular
intervals, the heart rate will be automatically
turned on for measurement. The measurement
time is 25s.
In sport mode, heart rate is on until you exit
sport mode.
Display description
long press
MON
Manual input
Device Management
Share
CW10C
CW10C
Bluetooth