RF-603 Wireless Flash Trigger / Synchronized Shutter Release Remote Control Transceiver 无线引闪 / 快门遥控同步收发器 User Manual EN 使用手册 中文
Contents General description ……………………………………………………1 Cautions …………………………………………………………………2 Include items ……………………………………………………………3 The name of each part for RF-603 ………………………………………4 Preparation before using …………………………………………………5 How to fix and install ……………………………………………………6 Wireless flash trigger & testing Wireless flash /studio flash trigger ……………………………………7 …………………………………8 Wired/wireless remote shutter release ……………………………………9 Function extend ……………………………………………………10-11 Specification ……………………………………………………………12
General description Thank you for purchasing YongNuo products in advance. Please read this user manual carefully and learn how to use camera and flash before. ●● RF-603 using a global free FSK 2.4GHz wireless channel which can be suitable in many country. RF-603 with FSK, can guarantee speed, distance and stability. Within capacious areas, the remote control distance may reach to 100m.
Cautions 1. 2. 3. 4. 5. 6. 7. 8. As this is an electronic product accessory, some of the environment causes may affect the working. However this is hardly ever to get this situation, don't worry. Do not pull the wires and turn off the camera when connecting. For a long time non-use, please turn the transceiver off and remove the batteries. Do not put it in high temperature, such as a closed car under direct sunlight, the control panel and other high temperature areas.
Include items EN RF-603N RF-603C (For Nikon only) (For Canon only) PC sync cable/Shutter connecting cable Two transceivers RF-603N or RF-603C attached in the package, work to receive and transmit, which can work under different condition by different connection of cameras and flash lights. Connecting cable and valuable attachments will be different according to different regions.
The name of each part for RF-603 ② ⑦ ① ③ OF F ④ ⑧ ON R FS F-6 K 0 AD 2.4 3N E IN G CH Hz IN ⑨ M A ⑤ ⑥ ⑩ EN RF-603N for Nikon RF-603C for Canon ① Awakening indicator light (green) /Flash trigger indicator light (red) ② Hot shoe / Hot shoe contacts ③ Power indicator light (green) /Shutter release indicator light(red) ④ Power switch ⑤ 2.
Preparation before using Channel Setting Opened the protective film, use the channel setting switch to set two or more transceivers as the same code. Battery installation Slide to open the battery room, install two AAA batteries for each transceiver according to the "+/-" marks shown. Power on/off Slide the power switch to "ON", the power indicator light will turn on(green), slide the power switch to "OFF" to turn off.
How to fix and install Fixing the flash on transceiver: Install the flash on the hot shoe of the transceiver, lock the flash and ensure all are fixed well. Fixing the transceiver on light stand: Mount the transceiver on the rack with fixing clip such as light stand bracket (B Type) by hot shoe mounting foot, and tight the locking screw. EN Fixing the transceiver on camera: Mount the transceiver on the hot shoe of the camera by hot shoe mounting foot. RF-603C for Canon camera ,RF-603N for Nikon camera .
Wireless flash trigger & testing Transceiver must be fixed on the camera for testing and triggering. Make sure all the transceivers are fixed well, the flash must be set to Manual mode. 1. Press the shutter release button halfway of the camera to focus, the flash will be awaken if the flash is on the status of sleep, awakening indicator light of transceivers will turn on(green) in same channel. 2.
Wireless flash/studio flash trigger sync Camera controls one or more flashes and studio flash lights. Purchase YongNuo studio flash PC sync cable according to different studio flash . 1. Insert the PC connecting cable plug with nut into the PC socket of transceiver. 2. Screw down the nut. 3. Fix the transceiver near the studio flash lights, and insert the cable plug with jack into the control socket of studio flash lights. 4.
Wired/wireless remote shutter release This product may achieve wired remote shutter release/ wireless remote shutter release, in support of single frame, continuous photograph, delay and bulb shooting modes. And the modes shall be set on the camera before using. Additional YongNuo 2.5mm shutter connecting cable needs Connected the shutter to be purchased. connecting cable as 1. Single transceiver can be used as a wired remote shown in the figure. shutter release.
Function extend Handhold the flash for remote flash trigger sync Take the RF-603 on flash light as shutter release remote control,additional YongNuo 2.5mm shutter connecting cable needs to be purchased. 1. Install the handhold flash on the hot shoe of the transceiver as transmitter. 2. Fixed the camera such as a tripod, installed the other transceiver on the hot shoe of the camera as receiver,and connected with specially shutter cable to the external shutter socket of the camera. 3.
Function extend EN 11 Remote shooting with flash trigger sync Several RF-603 combination using, additional YongNuo 2.5mm shutter connecting cable and more RF-603 transceivers needs to be purchased. 1. Install one of transceiver on the hot shoe of the camera, and connected the shutter connecting cable to the camera. 2. Install the flash on the hot shoe of the other transceivers, or connected with PC sync cable to studio flash lights. 3.
Specification Type: FSK 2.4GHz wireless remote control system Transmission distance: 100m Channels: 16 Shutter release: half-press, full-press Shutter interface: 2.5mm socket Studio flash light interface: standard PC socket Battery: AAA×2 Stand-by time: over 45 hours Size (W x H x D): 37mm×30mm×81.5mm EN HongKong YongNuo Photographic Equiment Co., Ltd. Address:G/F,4 Bulkeley Street, Hung Hom,Kowloon,HongKong After-sales:service@hkyongnuo.com Tel:(86) 755-837-62448 Web:www.hkyongnuo.
目录 产品功能简介······················1 注意事项························2 随附物品························3 RF-603 各部位名称····················4 使用前准备·······················5 固定及安装·······················6 无线引闪及测试························7 无线引闪闪光灯、影室灯················8 有线快门线、无线快门线功能···················9 功能延伸·······················10-11 规格·························12 中文
产品功能简介 首先感谢您购买永诺产品,在使用前,请您务必通读并理解本使用说明书和 相机及闪光灯的使用方法。 ●● RF-603 产品使用 2.
注意事项 1. 2. 3. 4. 5. 6. 7. 8.
随附物品 RF-603N RF-603C 尼康相机专用 佳能相机专用 中文 PC 同步线 / 快门连接线 包装内附 RF-603N 或 RF-603C 收发器两只,兼备收发 功能,在与相机和闪光灯的不同连接方式工作在不同的收 发状态下。连接线及增值附件根据不同区域将会有所不同。 3
RF-603 各部位名称 ② ⑦ ① ③ OF F ④ ⑧ ON R FS F-6 K 0 AD 2.4 3N E IN G CH Hz IN M A ⑤ ⑥ ⑨ ⑩ RF-603N 尼康相机专用 RF-603C 佳能相机专用 中文 ①唤醒指示灯(绿色)/ 触发指示灯(红色)②热靴座 / 热靴触点 ③电源指示灯(绿色)/ 快门指示灯(红色)④电源开关 ⑤ 2.
使用前准备 频道设置 揭开保护膜,使用频道设置开关把收发器设置在 相同的编码位置。 电池安装 打开电池仓,依照电池仓上的 “+/-”指示分别 为两只收发器安装两只 AAA 电池。 中文 开 / 关电源 将电源开关推到“ON”的位置开启电源 , 绿色 电源指示灯亮,推到“OFF”位置关闭。 ● 5 以下功能说明均为设置在相同频道时的两只或 多只收发器电源开启的状态下。
固定及安装 闪光灯固定于收发器上: 安装机载闪光灯在收发器的热靴坐上,锁紧闪光 灯,确保各环节连接牢固。 收发器固定于灯架上 : 收发器可利用热靴脚固定在 B 型灯架等带有固定 夹的支架上,并锁紧旋钮。 收发器固定于相机热靴座: 收发器利用热靴脚安装在相机机顶热靴即可,请 使用专用收发器(佳能单反相机使用 RF-603C、尼康 单反相机使用 RF-603N)。 中文 6
无线引闪及测试 收发器需固定于相机上进行闪光测试和闪光触 发 , 确认所有收发器已固定牢固,闪光灯需设置在 手动 "M" 模式。 1. 半按相机快门释放按钮,相机进行对焦动作 , 如果此时闪光灯处于休眠状态,将会被唤醒 , 相同频道的收发器绿色唤醒指示灯亮。 2. 在唤醒指示灯亮的状态下全按一下安装于机 顶热靴上的收发器的快门释放按钮,进行引 闪测试 , 离机闪光灯将被触发闪光一次。 3.
无线引闪闪光灯、影室灯 相机无线同步引闪一台或多台闪光灯、影室灯。实现此功能需要另购永 诺影室灯连接线,根据不同影室灯的控制接口使用不同的连接线。 1. 使用 PC 连接线带螺母插头插入收发器 PC 插座。 2. 旋紧螺母。 3. 将收发器固定在影室灯附近,使用 PC 连接线插头一端插入影室灯触发 插座。 4.
有线快门线 / 无线快门线功能 本产品可实现有线快门线 / 无线快门线功能,支 持单张、连拍、延时、B 门等模式拍摄,拍摄模式需 先行在相机上设定。实现此功能需要另购永诺 2.5mm 相机连接线,根据不同相机型号选择不同的连接线。 中文 9 1. 如图所示,单只收发器可作为有线快门线使用。 半按手中收发器的快门释放按钮进行对焦 , 全 按进行拍摄,同时红色快门指示灯亮。 2.
功能延伸 手持闪光灯遥控拍摄并同步引闪 使用装上闪光灯的 RF-603 作为快门遥控并同步引闪 , 本功能需另购永 诺 2.5mm 快门连接线。 1. 手持闪光灯安装在收发器的热靴座上作为发射器并锁紧闪光灯。 2. 固定好相机 ( 如三脚架上 ), 使用另一只收发器装于相机机顶热靴座作 接收器 , 并通过专 用快门连接线与相机的外接快门插座连接。 3.
功能延伸 无线遥控拍摄并同步触发闪光灯 多个 RF-603 组合使用的例子,实现此功能需另购永诺 2.5mm 相机快门 线及多只 RF-603 收发器。 1. 将一只收发器安装在相机机顶热靴座上,并使用快门连接线与相机快 门插座连接。 2. 将闪光灯安装在收发器的热靴座上,或与影室灯使用 PC 连接线连接。 3.
规格 类型:FSK 2.4GHz 无线遥控系统 传送距离:100 米 频道:16 个频道 快门释放:半按,全按 快门接口:2.5MM 接口 影室灯接口:标准 PC 接口 电池:AAA×2 待机时间:45 小时以上 体积(宽 × 高 × 深):37mm×30mm×81.5mm 深圳市永诺摄影器材股份有限公司 地址 : 深圳市华强北路赛格科技园二栋西 A511 室 电话:(86) 755-837-62448 售后服务:400-001-3888 网址:www.yongnuo.com.
V2.