User`s manual

D /ENS!ONS it\ [] ARE IN INCHES _EV_ORa_CO!L
706
[2 78]
{
[16OR]406 4
CONDENSER
REQUHREDCLEARANCE TO COMBUSTHBLEMATL.
TOP ViEW
IIR39
402 O
[15 83]
17 7
4 63)
88 ;/
[3 48]
_249 6_550 5 2496
[9 83] [21 67] [9 83]
REAR VIEW
\
2263
[48 28]
FRONT VHEW
b
i.. ._ so
1222
0 20)
[4 8!
RHOHT SHDE VmEW
INCHES [mm]
TOP OF UNIT .................................................. 1400 [355 6]
DUCT SIDE OF UNIT ............................................ .200 [50.8]
SIDE OPPOSITE DUCTS .............................................................. 1400 [355 6]
BOTTOM OF UNIT ................................................ .050 [12.7]
ELECTRIC HEAT PANEL ....................................... 3600 [914 4]
NEC. REQUIRED CLEARANCES.
INCHES [mm]
BETWEEN UNITS, POWER ENTRY SIDE ................................... 4200 [1066 8]
UNIT AND UNGROUNDED SURFACES, POWER ENTRY SIDE 3600 [914 0]
UNIT AND BLOCK OR CONCRETE WALLS AND OTHER
GROUNDED SURFACES, POWER ENTRY SIDE ........................ 4200 [1066 8]
REQUHREDCLEARANCE FOR OPERATION AND SERVHCBNG
INCHES [mm]
EVAR COIL ACCESS SIDE. ........................................ 3&00 [914.0]
POWER ENTRY SIDE. ................................................ 4200 [106&6]
(EXCEPT FOR NEC REQUIREMENTS)
UNIT TOP ................................................................... 4&00 [!21&2]
SIDE OPPOSITE DUCTS ........................................... 3&00 [914_0]
DUCT PANEL ....................................................................... 1200 [304_8] *
_MINIMUM DISTANCES: IF UNF IS PLACED LESS THAN 3048 [12.00] FROM
WALL SYSTEM, THEN SYSTEM PERFORMANCE MAYBE COMPROMISE
C99007
UNIT
80GS0t8
80GS024
80GS030
SOGS03G
80GS042
80GX024
80GX030
50GX035
EL_=CTRICAL CHARACTERBSTICS
208/230-1-60
208/230-1-60
208/230-1-60, 208/230-3-60
208/230-1-60, 208/230-3-60, 460-3-60
208/230-1-60, 208/230-3-60, 460-3-60
208/230-1-60
208/230-1-60, 208/230-3-60
208/230-1-60, 208/230-3-60, 460-3-60
UNIT WEIGHT
lb. kg
254 115.2
260 117.9
258 117.0
268 121.6
294 133.3
270 122.5
291 132.0
299 135.6
UNIT HEIGHT
IN. (MM)
_A_
35.02 (889.5)
35.02 (889.5)
35.02 (889.5)
37.02 (940.3)
35.02 (889.5)
37.02 (940.3)
39.02 (991.1)
35.02 (889.5)
CENTER OF GRAWTY
iN. (NM)
X
20.0 (508.0)
19.0 (482.6)
19.0 (482.6)
2010 (508.0)
19.0 (482.8)
18.5 (469.9)
19.5 (495.3)
19.5 (495.3)
Y Z
13.0 (330.2) 15.0 (381.0)
13.0 (330.2) 15.o(381.o)
14.o (355.6) laO (381.o)
14.o (355.6) 13.o (330.2)
14.o (355.6) 13.o (330.2)
14.5 (368.3) 16.o (40614)
15.5 (393.7) 17.6 (447.0)
15.25 (387.4) 16.5 (419.1)
Fig. 2-- 50GS018o042 and 50GX024o036 Unit Dimensions
Accessory lifting kit is only to bc usd with Small Packaged
units wNch have a composite base pan with molded rigging
holds.
INSPECTION
Prior to initial use, and at mommy intervals, all rigging brackets
and straps should bc visually inspected _br any damage, evidence
of wear, structural deformation, or cracks Particular attention
should be paid to excessive wear at hoist hooking points and toad
support areas Brackets or straps showiug any kind of wear in (hose
areas must not be used and should be discarded
INSTALLATION
1 Position the lifting bracket assembly around the base of the
m-dr. Leave the top shipping skid on the unit to act as a
spreader bar Be sure the strap does not twist.