Specifications
Table Of Contents
- Form 150.72-NM1 (908)
- GENERAL SAFETY GUIDELINES
- CHANGEABILITY OF THIS DOCUMENT
- TABLE OF CONTENTS
- LIST OF FIGURES
- LIST OF TABLES
- SECTION 1 – GENERAL CHILLER INFORMATION & SAFETY
- SECTION 2 – PRODUCT DESCRIPTION
- INTRODUCTION
- GENERAL SYSTEM DESCRIPTION
- HIGH AMBIENT KIT
- BUILDING AUTOMATION SYSTEM INTERFACE
- MILLENIUM CONTROL CENTER
- POWER PANEL
- ACCESSORIES AND OPTIONS
- UNIT COMPONENTS
- CONTROL / POWER PANEL COMPONENTS
- PRODUCT IDENTIFICATION NUMBER (PIN)
- BASIC UNIT NOMENCLATURE
- REFRIGERANT FLOW DIAGRAM
- PROCESS AND INSTRUMENTATION DIAGRAM
- SECTION 3 – HANDLING AND STORAGE
- SECTION 4 – INSTALLATION
- INSTALLATION CHECKLIST
- HANDLING
- INSPECTION
- LOCATION AND CLEARANCES
- SPRING ISOLATORS (OPTIONAL)
- COMPRESSOR MOUNTING
- REMOTE COOLER OPTION
- CHILLED LIQUID PIPING
- PIPEWORK ARRANGEMENT
- DUCT WORK CONNECTION
- WIRING
- COMPRESSOR HEATERS
- RELIEF VALVES
- HIGH PRESSURE CUTOUT
- SINGLE-POINT SUPPLY CONNECTION – TERMINAL BLOCK, NON-FUSED DISCONNECT SWITCH OR CIRCUIT BREAKER
- USER CONTROL WIRING INPUTS
- USER CONTROL WIRING OUTPUTS
- SECTION 5 – TECHNICAL DATA
- OPERATIONAL LIMITATIONS (ENGLISH)
- HEAT EXCHANGER FLOW, GPM
- PHYSICAL DATA (ENGLISH)
- ELECTRICAL DATA
- ELECTRICAL NOTES
- ELECTRICAL DATA W/O PUMPS
- ELECTRICAL DATA W/ PUMPS
- ELECTRICAL NOTES AND LEGEND
- WIRING DIAGRAMS
- DIMENSIONS (ENGLISH)
- TECHNICAL DATA – CLEARANCES
- WEIGHT DISTRIBUTION AND ISOLATOR MOUNTING POSITIONS
- ISOLATOR INFORMATION FOR UNITS SHIPPED ON OR AFTER JUNE 15, 2008
- ISOLATOR INFORMATION FOR UNITS SHIPPED BEFORE JUNE 15, 2008
- SLRS Seismic Isolator Specifications
- SLRS Seismic Isolator Installation and Adjustment
- One Inch Deflection Spring Isolator Cross-reference
- Installation of 1” Deflection Mounts
- Neoprene Isolator Cross-reference
- Two Inch Deflection, Seismic Spring IsolatorCross-reference - SLRS
- SLRS Seismic Isolator Installation and Adjustment
- SECTION 6 – COMMISSIONING
- SECTION 7 – UNIT CONTROLS
- SECTION 8 – UNIT OPERATION
- CAPACITY CONTROL
- SUCTION PRESSURE LIMIT CONTROLS
- DISCHARGE PRESSURE LIMIT CONTROLS
- LEAVING CHILLED LIQUID CONTROL
- LEAVING CHILLED LIQUID CONTROLOVERRIDE TO REDUCE CYCLING
- LEAVING CHILLED LIQUID SYSTEM LEAD/LAG AND COMPRESSOR SEQUENCING
- RETURN CHILLED LIQUID CONTROL
- RETURN CHILLLED LIQUID SYSTEM LEAD/LAG AND COMPRESSOR SEQUENCING
- ANTI-RECYCLE TIMER
- ANTI-COINCIDENCE TIMER
- EVAPORATOR PUMP CONTROL & YORK HYDRO KIT PUMP CONTROL
- EVAPORATOR HEATER CONTROL
- PUMPDOWN CONTROL
- STANDARD CONDENSER FAN CONTROL
- LOAD LIMITING
- COMPRESSOR RUN STATUS
- ALARM STATUS
- REMOTE BAS/EMS TEMPERATURE RESET USINGA VOLTAGE OR CURRENT SIGNAL
- SECTION 9 – SERVICE AND TROUBLESHOOTING
- SECTION 10 – MAINTENANCE
JOHNSON CONTROLS
94
FORM 150.72-NM1 (908)
Technical Data
ONE INCH DEFLECTION SPRING ISOLATORS INSTALLATION INSTRUCTIONS
Units shipped on or after June 15, 2008
1. READ INSTRUCTIONS IN THEIR ENTIRETY BEFORE BEGIN-
NING INSTALLATION.
2. ISOLATORS ARE SHIPPED FULLY ASSEMBLED AND ARE TO
BE POSITIONED IN ACCORDANCE WITH THE SUBMITTAL
DRAWINGS OR AS OTHERWISE RECCOMENDED.
3. SET ISOLATORS ON FLOOR, HOUSEKEEPING PAD OR SUB-
BASE, ENSURING THAT ALL ISOLATORS CENTERLINES
MATCH THE EQUIPMENT MOUNTING HOLES. THE VMC
GROUP RECCOMENDS THAT THE ISOLATOR BASE (“B”)
BE INSTALLED ON A LEVEL SURFACE. SHIM OR GROUT
AS REQUIRED, LEVELING ALL ISOLATORBASES TO THE
SAME ELEVATION (1/4-INCH MAXIMUM DIFFERENCE CAN
BE TOLERATED).
4. BOLT OR ANCHOR ALL ISOLATORS TO SUPPRTING STRUC-
TURE UTILIZING BASE SLOTTED HOLES (“C”).
5. PLACE EQUIPMENT ON TOP OF ISOLATORS MAKING SURE
THAT MOUNTING HOLES OF THE EQUIPMENT LINE UP
WITH ISOLATOR POSITIONING PIN (“H”).
6. THE ADJUSTMENT PROCESS CAN ONLY BEGIN AFTER
THE EQUIPMENT OR MACHINE IS AT ITS FULL OPERATING
WEIGHT.
7. ADJUST EACH ISOLATOR IN SEQUENCE BY TURNING
SPRING ADJUSTING BOLT (“D”) ONE FULL COUNTER-
CLOCKWISE TURN AT A TIME. REPEAT THIS PROCEDURE
ON ALL ISOLATORS, ONE AT A TIME.
8. CONTINUE ADJUSTING EACH ISOLATOR UNTIL A MINI-
MUM OF 1/4” CLEARANCE IS ACHIEVED BETWEEN THE
LOWER HOUSING AND UPPER HOUSING. (SEE DRAWING
BELOW).
9. FINE ADJUST ISOLATORS TO LEVEL EQUIPMENT.
10. INSTALLATION IS COMPLETE.
LD13790