YDS-R51-0408 ENGLISH OWNER’S MANUAL REMOTE CONTROLLER R51 Please read this installation manual carefully before installing your air conditioner. Please keep this manual in a safe place for future reference. This manual many be subject to change without notice for purpose of improvement.
CONTENTS Remote Controller Specifications---------------------------------------1 Performance Features----------------------------------------------------- 1 Introduction of Function Buttons on the Remote Controller---1 Names and Functions of indicators on Remote Controller---- 3 Operating the Remote Controller---------------------------------------4 Warning--------------------------------------------------------------------------7
Remote Controller Specifications Model R51, R51/BG,R51/E,R51/CE,R51/BGE,R51/CBGE Rated Voltage 3.0V Lowest Voltage of CPU Emitting Signal 2.0V 8m (when using 3.0 voltage, it Gets 11m) Reaching Distance Environment Temperature Range 。 。 -5 C 60 C Performance Features 1. Operating Mode: COOL、HEAT、DRY、FAN and AUTO . 2. Timer Setting Function in 24 hours. 。 。 3. Indoor Setting Temperature Range : 17 C~30 C. 4. LCD (Liquid Crystal Display) of all functions. 5.
1 TEMP Button : Push the TEMP button to decrease the indoor temperature setting or to adjust the TIMER in a counter-clockwise direction. 2 MODE Select Button: Each time you push the button, a mode is selected in a sequence that goes from AUTO、 COOL、 DRY、 HEAT and FAN as the following figure indicates: AUTO(COOL) COOL DRY HEAT FAN NOTE: HEAT only for Heat Pump 3 SWING Button: Push this switch button to change the louver angle .
Names and Functions of indicators on Remote Controller Display Panel 1 6 2 5 AUTO COOL DRY HEAT FAN HIGH MED LOW 3 4 Fig. 2 1 TRANSMISSION Indicator: This indicator lights when remote controller transmits signals to indoor unit. 2 MODE Display: Shows the current operation modes-- AUTO, COOL, DRY and HEAT. HEAT only available for heat pump model. 3 HEAT PUMP ONLY - LOCK display is displayed by pushing the LOCK button. Push the LOCK button again to clear display.
Operating the Remote Controller Install / Replace Batteries The Remote Controller uses two alkaline dry batteries(R03/Ir03X2). 1. To install batteries, slide back the cover of the battery compartment and install the batteries according to the directions (+and -) shown on the Remote Controller. 2. To replace the old batteries , use the same method as mentioned above. NOTE 1. When replacing batteries, do not use old batteries or a different type battery. This may cause the remote controller to malfunction.
COOL , HEAT, and FAN ONLY Operation 1. If the AUTO mode is not comfortable , you may manually override the settings by using COOL, DRY, HEAT( HEAT PUMP units only), or FAN ONLY modes. 2. Push the TEMP button to set the desired room temperature. 。 When in COOLING mode, the most comfortable settings are 21 C or above. When in HEATING mode, the most comfortable settings 。 are 28 C or below. 3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH, MED or LOW. 4. Push the ON/OFF button.
2. To set the STOPPING time. 2.1 Please press the CANCEL button to cancel any former settings. 2.2 Push the TIMER button and the remote controller will show the last set time for the START operation and the signal "h" will be shown on the display panel. You are now ready to readjust the TIMER OFF to stop the operation. 2.3 Push the TEMP button to cancel the TIMER ON setting. The digital area will show "00". 2.
Warning 1. Be sure there are no barriers between the remote controller and the receiver of indoor unit otherwise the air conditioner will not work. 2. Keep the Remote Controller away from all liquids. 3. Protect the Remote Controller from high temperatures and exposure to radiation. 4. Keep the indoor receiver out of direct sunlight or the Air Conditioner may malfunction. 5. Keep controller away from EMI (Electro-Magnetic Interference) supplied by other household appliances.
DE - COMMISSIONING DISMANTLING & DISPOSAL This product contains refrigerant under pressure, rotating parts, and electrical connections which may be a danger and cause injury! All work must only be carried out by competent persons using suitable protective clothing and safety precautions. Read the Manual Risk of electric shock Unit is remotely controlled and may start without warning 1. Isolate all sources of electrical supply to the unit including any control system supplies switched by the unit.