Electric Fireplace Instruction Manual Wall Hanging Electric Fireplace Packing List 1 Electric Fireplace 1 Glass Face 1 Remote Control 2 AAA Batteries 1 Instruction Manual 1 Wall Fixing Plate 1 Fastener Package Yosemite Home Décor 1-800-305-9872 www.YosemiteHomeDecor.
INSTALLATION INSTRUCTIONS Location 1. The fireplace may be hanged on any wall surface that can support its weight and where it can be leveled. As it does not irradiate any heat from the back and no rear clearances are needed. 2. The heater, which is located at the base of the fireplace, must be a minimum of 16 inches away from any combustible material. 3. It is important that the wall on to which the fireplace is to be installed is of sound construction.
Installation Figure 1 1. Select the position of the fireplace on the wall to which it is to be mounted. Draw a level horizontal line on the wall at the required height. This line will correspond to the top of the fireplace so it is important to allow for the extra height of the glass face. 2. Mark the center line of the fireplace on to the horizontal line. 3. Place the Installation Plate along the horizontal line and line up the center “V” cut out with the center line. See Figure 1. 4.
8. Lift the fireplace and place the keyhole slots situated on the back of the fire (Figure 2) to the location pins on the mounting plate. A gentle application of downward pressure will lock it into place. Make sure all of the pins have been located into the top section of each keyhole fixing slot.
Electrical Work This fireplace must be grounded 9. A standard electrical outlet must be close to the fireplace. If the electric outlet is required to be concealed, it can be located above or on the right hand side of the fire and behind the glass face. 10. DO NOT INSTALL THE FIREPLACE WHERE THE HEATER IS DIRECTLY ABOVE AN OUTLET The fireplace’s vent is located in the center of the fireplace base. 11. If the power supply cable becomes damaged in any manner it MUST be replaced. 12.
Attaching the Face Two people may be required to carry out this installation 1. On each side of the fireplace are two locating studs (Figure 5). 2. On the back of the face there are two brackets which hook over these studs. 3. Lift the face up to the fireplace. Then lower the face into place so that the brackets on the rear of the face locate either side of the studs on the fireplace. Once in place firmly tighten the locking bolt.
OPERATING INSTRUCTIONS CAUTIONS: 1. When the fireplace is in operation certain areas of the fireplace surface will get hot. Caution must be taken to avoid being burned. Take care not to touch hot surfaces. 2. The fireplace must not be switched on if volatile vapors are present in the room 3. Children must be supervised around the fireplace. 4. Do not obstruct the air flow around the fireplace. 5.
Fireplace Control Panel The control panel is located on the right hand side of the fireplace (Figure 7).
Remote Control DIMMER A B C D E ON/OFF HIGH HIGH\LO W Infrared Window On/Off Switch Flame Effect Dimmer Heater Maximum Heat Heater Low Heat 1. Prior to use, the remote control handset requires installation of the two included AAA batteries (Figure 8). 2. Remove the cover on the rear of the remote control by sliding backwards. Install the batteries as shown and then slide the cover back into the original position. 3.
D Heater Maximum Heat (1500 W) Press this once to switch to high heat. The indicator light will come on as well as the fan. Press again to turn off. (The fan will continue to run for a few moments until sensors indicate cool condition) E Heater Low Heat (750 w) Press this once to switch to high heat. The indicator light will come on as well as the fan. Press again to turn off.
MAINTENANCE INSTRUCTIONS Changing Light Bulbs Disconnect power supply before beginning any maintenance. 1. Light bulbs need to be replaced when you notice a dark section of the flame or when clarity and detail of the coal effect disappears. 2. Unscrew the locking nut on the side of the brackets and then remove the face. This is done by lifting the face up and swinging the face clear of the fire. Care should be taken not to damage the face. Removal of the face may require two people. 3.
