Electric Fireplace Instruction Manual Electric Fireplace Packing List 1 Electric Fireplace 1 Remote Control 2 AAA battery 1 Fastener Package 1 Instruction Manual Yosemite Home Décor 1-800-305-9872 www.YosemiteHomeDecor.
Quick Reference Guide I. II. III. Prior to installation, please ensure: 1. The rated voltage of your firebox fits the output voltage of your outlet; 2. The light bulbs in your firebox are in good condition. To check this, please follow the instructions for replacing the light bulbs on section MAINTENANCE. The heater on your electric fireplace may emit a slight, harmless odor when first used. This odor is a normal condition caused by the initial heating of internal heater parts and will not occur again.
IMPORTANT INSTRUCTIONS WARNING You should read and always follow the important instructions below to reduce the risk of fire, electric shock, and injury to persons. 1. Read all instructions before using this heater. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces, such as surfaces near the heater outlet or light bulbs. The grill directly in front of the heater outlet becomes hot during heater operation. If provided, use handles when moving this heater.
13. All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to flammable vapours. 14. Do not modify this heater. Use it only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. 15. Always plug heaters directly into a wall outlet/receptacle.
INSTALLATION This section provides step-by-step instructions for installation of your fireplace insert. Site Selection Review and consider all of the following conditions for installation: • • Dimensions of the unit Unit requires a minimum of two (2) wall studs in order to ensure a secure installation. The fireplace insert comes completely assembled and wired. Some tools may be required to prepare the site and assembly/install the trim.
Existing Fireplace Installation 1. Seal all drafts and vents with non-fibrous insulation materials to prevent chimney debris from falling into the fireplace insert. CAUTION Do not install into an existing fireplace that is prone to leaks or dampness. 2. Cap the top of the chimney flue to prevent rain from entering. 3. Plug the fireplace into a 15A/120V outlet. 4. The power cord can run along the front of the hearth to an outlet near the fireplace.
Wall Construction Installation 1. Select a suitable location that is not susceptible to moisture or dust. Keep away from high traffic areas. Also, keep away from things that may catch fire such as drapes and furniture etc. 2. Use studs to frame an opening, make sure to create an allowance of ¾ inches (2.0 cm) based on the inserts’ dimension to ensure that the fireplace could be inserted without any problems. 3. Plug the fireplace into a 15A/120V outlet.
GROUNDING INSTRUCTIONS This heater is for use on 120 volts. The cord has a plug as shown at A in Figure. An adapter as shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
OPERATION This section will explain the function of each convenient control. NOTE The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused by initial heating of internal heater parts and will not occur again. • Control Panel Operation A.
B. Operation On the first use of remote controller, install the batteries first: open the battery box by sliding its cover along the arrow, install two AAA batteries according to the marks in the box, and slide the cover to its original position. If no batteries installed or the batteries are not working, the remote controller will be unusable. To use the remote controller effectively, point it to the electric fireplace and keep a distance of 1-5 meters.
MAINTENANCE WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock to persons or damage. Light Bulb Replacement Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. WARNING Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid burning of skin.
Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.