User Manual

17
All AGM battery electrolyte
containers are not the same.
Each contains the proper
amount of electrolyte
for its specifi c battery.
Before fi lling, read the electrolyte handling instructions and
precautions on the label. Do not smoke when activating a
battery or handling battery acid. Always wear plastic gloves
and protective eyewear and be sure to read the Battery Safety
section in this manual. The following seven steps should be
used to activate an AGM battery:
1. The battery must be out of the vehicle and placed on a level
surface.
2. Remove electrolyte
container from
the plastic storage
bag. Remove the
strip of caps. Put
the strip aside
as you will use it
later to seal the
battery cells. For
battery fi lling use
only the dedicated
acid container
that comes with
the battery as
it contains the
proper amount of
electrolyte for that
specifi c battery. This is important to service life and battery
performance. Do not pierce, or otherwise open the foil
seals on the electrolyte container. Do not attempt to
separate the individual electrolyte containers.
3. Place the electrolyte container with the foil seals facing
down into the cell fi ller ports on the battery. Hold the
container level and push down to break the foil seals.
Electrolyte will start to fl ow into the battery and air
bubbles will be seen inside the container. Do not tilt the
electrolyte container.
4. Check the electrolyte fl ow. Keep the container in place
for
20 minutes or longer until it empties completely.
If no air bubbles are coming up from the fi ller ports, or if
container cells haven’t emptied completely after
20 minutes,
tap the container and/or battery case a few times to cause
the electrolyte to fl ow into the battery. Do not remove the
acid container from
the battery until
it is completely
empty. The battery
requires all of the
electrolyte from
the container for
proper operation.
5. Remove the empty electrolyte container from the battery.
Fully insert the strip of sealing caps (previously removed
from the electrolyte container) into the battery fi lling ports.
Make sure the strip of caps is fully inserted and fl ush with
the top of the battery. Insert the caps by hand, do not use
Keep this strip
The electrolyte container that
is shipped with a dry AGM
battery contains the correct
amount of battery acid and
is more concentrated that
the electrolyte used in a
conventional battery.
Do not puncture the foil seal or remove it prior to fi lling a dry AGM battery.
Gently tap
electrolyte
container
MADE IN USA
YUAS
A
B
ATTER
Y
, INC.
READING, PA
19605
ISO 9000
PPPPSAE
12V 18Ah 10HR
VRLA
YTX20HL-BS
M620BH
CHARGING METHOD: 1.8 Amps x 5~10 hrs
www.yuasabatteries.com
HIGH PERFORMANCE
(
)
()
18.9 Ah 20HR / 310A CCA
( )
( )
Bubbles will appear as the
electrolyte container fi lls
the battery indicating the
fl ow of battery acid. Tap
the container periodically
to keep the electrolyte
fl owing until the container
is completely empty.
Never puncture the top
of the acid container
to speed up the fi lling
process.
After fi lling, the sealing caps should be installed using hand
pressure only. The sealing cap should never be removed once the
battery is activated.
R
MADE IN USA
YUASA BATTERY, INC.
READING, PA 19605
ISO 9000
CHARGING METHOD: 1.8 Amps x 5~10 hrs
www.yuasabatteries.com
HIGH PERFORMANCE
)
18 9 Ah 20HR / 310A CCA
( )
( )
SAE
12V 18Ah 10HR
VRLA
YTX20HL-BS
M620BH
YUE-094 REV_A
()
MADE IN USA
YUASA BATTERY, INC.
READING, PA 19605
ISO 9000
PP
PP
CHARGING METHOD: 1.8 Amps x 5~10 hrs
www.yuasabatteries.com
HIGH PERFORMANCE
(
)
18.9 Ah 20HR / 310A CC
( )
(