User's Manual

Health and Safety Information
Important Health Information and Safety Precautions
When using this product, the safety precautions below must be taken to avoid possible
legal liabilities and damages. Retain and follow all product safety and operating
instructions.
Observe all warnings in the product operating instructions. To reduce the risk of bodily
injury, electric shock, fire and damage to the equipment, closely observe all of the
following precautions.
Safety Precautions for Proper Grounding Installation
Caution: Connecting to improperly grounded equipment can result in an electric shock to
either you or your device. This product is equipped with a USB Cable for connecting to a
desktop or notebook computer. Be sure your computer is properly grounded before
connecting this product to the computer. The power supply cord of a desktop or
notebook computer has an equipment-grounding conductor and a grounding plug. The
grounding plug must be plugged into an appropriate outlet which is properly installed
and grounded in accordance with all local codes and ordinances.
Safety Precautions for Power Supply Unit
Use the correct external power source. A product should be operated only from the type
of power source indicated on the electrical ratings label. If you are not sure of the type of
power source required, consult your authorized service provider or local power company.
For a product that operates from battery power or other sources, refer to the operating
instructions that are included with the product.
Electrical Safety
This product is intended for use when supplied with power from the designated battery
or power supply unit. Other usage may be dangerous and will invalidate any approval
given to this product. Handle battery packs carefully. This product contains a Li-ion
battery. There is a risk of fire and burns if the battery pack is handled improperly. Do not
attempt to open or service the battery pack. Do not disassemble, crush, puncture, short
external contacts or circuits, dispose of in fire or water, or expose a battery pack to
temperatures higher than 60°C (140°F).
Note: Danger of explosion if battery is incorrectly replaced. Replace only with specified
batteries. To replace the battery, take the device to an authorized service centre. Recycle
or dispose of used batteries according to all applicable local regulations, or in accordance
with the instructions in the reference guide.
Follow these other specific precautions:
1. Keep the battery or device dry and away from water or any liquid as it may cause a
short circuit.
2. The phone should be connected only to products that bear the USB-IF logo or have
completed the USB-IF compliance program.
3. Keep metal objects away so they do not come in contact with the battery or its
connectors as it may lead to short circuit during operation.
4. Always keep the battery out of the reach of babies and small children to avoid
swallowing. Consult a doctor immediately if the battery is swallowed.
5. Do not use a battery that appears damaged, deformed, discolored, has any rust on its
casing, if it overheats, and/or if it emits a foul odor.
6. Use of an unqualified battery or charger may present a risk of fire, explosion, leakage
or other hazard.
7. Only use the battery with a charging system that has been qualified with the system
per this standard: IEEE-Std-1725-200x.
8. Use of an unqualified battery may present a risk of fire, explosion, leakage or other
hazard.
9. Replace the battery only with another battery that has been qualified with the system
per this standard: IEEE-Std-1725-200x.
10. Avoid dropping the phone or battery. If the phone or battery is dropped, especially
on a hard surface causing damage, take it to a service center for inspection.
11. If the battery leaks: Do not allow the leaking fluid to come in contact with eyes. If
contact occurs, DO NOT rub the eyes. Rinse with clean water immediately and seek
medical advice. Do not allow the leaking fluid to come in contact with skin or clothing. If
contact occurs, flush the affected area immediately with clean water and seek medical
advice. Take other precautions to keep a leaking battery away from fire as there is a
danger of ignition or explosion.
Health & Safety
Warranty Guide
5. Cleaning – Unplug this from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners to clean; use only a dry cloth.
6. Water and moisture – Do not use this product under moist environment.
7. Self-servicing – Attempting to service this product on your own, or opening or
removing device covers may result in exposure to dangerous voltage or other hazards.
8. Unplug this apparatus during lighting storms or when unused for lengthy durations.
9. This Travel Charger is not intended to be repaired by service personnel in case of
failure or component defect.
FCC Notice and Cautions
This device and its accessories comply with Part 15 of FCC Rules.
Operation is subject to the following conditions:
(1) This device and its accessories may not cause harmful interference.
(2) This device and its accessories must accept any interference received, including
interference that may cause undesired operation.
Part 15.21 Statement：
Changes or modifications that are not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
Part of Statement 15.105:
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If you experience interference with reception (e.g., television),
determine if this equipment is causing the harmful interference by turning the equipment
off and then back on to see if the interference is affected.
If necessary, try correcting the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for further assistance.
HAC
This phone meets the M4/T4 level rating.
This phone has been tested and rated for use with hearing aids for some of the wireless
technologies that it uses. However, there may be some newer wireless technologies used
in this phone that have not been tested yet for use with hearing aids. Therefore, it is
important to experiment with the various features of this phone and in different locations
using your hearing aid or cochlear implant, to determine if you hear any interfering noise.
Consult your service provider or the manufacturer of this phone for information on
hearing aid compatibility. If you have questions about return or exchange policies, consult
your service provider or phone retailer.
TIA Safety Information
The following is the complete TIA Safety Information for wireless handheld phones:
Exposure to Radio Frequency Signal
Your wireless handheld portable phone is a low-power radio transmitter and receiver.
When ON, it receives and sends out Radio Frequency (RF) signals. In August 1996, the
Federal Communications Commissions (FCC) adopted RF exposure guidelines with
safety levels for handheld wireless phones. Those guidelines are consistent with the
safety standards previously set by both U.S. and international standards ‘bodies, as
follows:
ANSI C95.1 (1992) *
NCRP Report 86 (1986)
ICNIRP (1996)
* American National Standards Institute; National Council on Radiation Protection and
Measurements; International Commission on Non-Ionizing Radiation Protection. Those
standards were based on comprehensive and periodic evaluations of the relevant
scientific literature. For example, over 120 scientists, engineers, and physicians from
universities, government health agencies, and industry reviewed the available body of
research to develop the ANSI Standard (C95.1). The design of your phone complies with
the FCC guidelines (and those standards).
the equipment and for personal safety, it is recommended that no part of the human
body should come too close to the antenna during equipment operation.
Use only the supplied integral antenna. Use of unauthorized or modified antennas may
impair call quality and damage the phone, causing loss of performance and SAR levels
exceeding the recommended limits, as well as causing non-compliance with local and
national regulatory requirements. In order to limit RF energy exposure and to ensure
optimal phone performance, operate the device only it its normal-use position. Contact
with the antenna area may impair call quality and cause your device to operate at a
higher power level than needed which can reduce antenna performance and battery life.
Battery Information and Precautions
To assure product safety, there shall be precautions below.
Danger!
- Use dedicated chargers and follow the specified conditions when charging the cell.
- Use the cell only with the specified equipment.
- Do not put or store cell together with metal articles such as necklaces, hairpins, coins, or
screws.
- Do not short circuit the (+) and (-) terminals with metal conductors.
- Do not place cell in a device with the (+) and (-) in a reverse way.
- Do not penetrate cell with a sharp articles such as a needle.
- Do not disassemble the cell.
- Do not weld the cell directly.
- Do not use a seriously damaged or deformed cell.
- Thoroughly read the user’s manual before use, Inaccurate handling of lithium ion cell
may result in heat, fire, explosion, damage or the capacity loss of the cell.
Warning!
- Do not put cell into a heating vessel, washing machine or high-pressure container.
- Do not use cell with primary batteries, or batteries of a different package, type, or
brand.
- Stop charging the cell if charging is not completed within the specified time.
- Stop using the cell if abnormal heat, odor, discoloration, deformation or abnormal
condition is detected during use, charge, or storage.
- Keep away from cell immediately when leakage or foul odor is detected.
- Wash well with clean water immediately if liquid leaks onto your skin or clothes.
- If liquid leaking from the cell gets into your eyes, do not rub your eyes. Wash them well
with clean water and call physician immediately.
Caution!
- Store batteries out of reach of children so that they are not accidentally swallowed or
handled.
- If younger children use the cell, their guardians should explain the proper handling.
- Be sure to read the user’s manual and cautions on handling thoroughly before using the
cell.
- Batteries have cycle life. Replace failed cell with a new cell that is the same brand
immediately after normal life cycle expiration, or if expiration has occurred prematurely.
Store battery in a low-humidity and low-temperature environment if the battery won’t be
used for an extended period of time.
- Keep it far away from articles or materials with static electric charges while the cell is
charged, used or stored.
- Wipe with a dry cloth before using the cell if the terminals of the cell become dirty.
Safety Instructions of Travel Charger
Please read the following information carefully.
1. The maximum ambient temperature of the travel charger shall not exceed 40°C (104
degrees F).
2. The Travel Charger shall be installed according to specification. The current of load
and output power shall not exceed the following value:
Input: AC100-240V~ 50/60Hz 0.25A
Output: DC5V 1A
3. The Travel Charger shall be used for I.T. equipment only.
4. For indoor use only.
Prevention of Hearing Loss
Caution: Permanent hearing loss may occur if earphones or headphones are used at
high-volume levels for prolonged periods of time.
Safety Precautions for Direct Sunlight
Store this product away from excessive moisture and extreme temperatures. Do not leave
the product or its battery inside a vehicle or in places where the temperature may exceed
60°C (140°F), such as on a car dashboard, window sill, or behind glass that is exposed to
direct sunlight or strong ultraviolet light for extended periods of time. This may damage
the product, overheat the battery, or pose a risk to the vehicle.
Environmental Restrictions
Do not use this product in gas stations, fuel depots, chemical plants or where blasting
operations are in progress, or in potentially explosive atmospheres such as fueling areas,
fuel storehouses, below deck on boats, chemical plants, fuel or chemical transfer or
storage facilities, and areas where the air contains chemicals or particles, such as grain,
dust, or metal powders. Please be aware that sparks in such areas could cause an
explosion or fire resulting in bodily injury or even death.
Aircraft Safety
Due to the possible interference caused by this product to an aircraft’s navigation system
and its communications network, using this device’s phone function on board an airplane
is prohibited in most countries. If flight personnel authorize use of electronic devices,
switch device to Airplane Mode (consult User Guide for instructions) to turn off RF
functions that may cause interference.
Road Safety
In many jurisdictions, vehicle operators are not permitted to use communication services
with handheld devices while the vehicle is in motion, except in the case of emergency. In
some countries, using hands-free devices as an alternative is allowed.
Safety Precautions for RF Exposure
1. Use of non-original, non-manufacturer-approved accessories may violate your local RF
exposure guidelines and should be avoided.
2. Use only original, manufacturer-approved accessories when such accessories contain
metal of any kind.
3. Avoid using your phone near strong electromagnetic sources, such as microwave
ovens, sound speakers, TV and radio.
4. Avoid using your phone near metal structures (for example, the steel frame of a
building).
Explosive Atmospheres
When in an area with a potentially explosive atmosphere or where flammable materials
exist, the device should be turned off and the user should obey all signs and instructions.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or even
death. Users are advised not to use the equipment at refueling points such as service or
gas stations, and are reminded of the need to observe restrictions on the use of radio
equipment in fuel depots, chemical plants, or where blasting operations are in progress.
Areas with a potentially explosive atmosphere are often, but not always, clearly marked
such as fueling areas, below deck on boats, fuel or chemical transfer or storage facilities,
and including, but not limited to areas where the air contains chemicals or particles such
as grain, dust, or metal powders.
Interference with Medical Equipment Functions
This product may cause medical equipment to malfunction. The use of this device is
prohibited in most hospitals and medical clinics for which regulations and rules are
commonly posted in such facilities. In these instances, turn your phone OFF as health care
facilities frequently use equipment that is adversely affected by RF energy. If you use any
personal medical device(s), consult the manufacturer of your device(s) to determine if the
device(s) is adequately shielded from external RF energy. Your health care provider may
be able to assist you in obtaining this information.
Non-ionizing Radiation
Your device has an internal antenna. This product should be operated in its normal-use
position to ensure the radiative performance and safety from interference. As with other
mobile radio transmitting equipment, users are advised that for satisfactory operation of
salivary gland tumors), leukemia, or other types of cancer. None of the studies
demonstrated the existence of any harmful health effects from wireless phone RF
exposures. However, none of the studies can provide absolute findings about long-term
exposures since the average period of phone use in these studies was approximately
three years.
4. What kinds of phones are the subjects of this update?
Here the term “wireless phone” refers to handheld wireless phones with built-in antennas,
often called “cell” or “mobile” phones. These types of wireless phones can expose the
user to measurable Radio Frequency (RF) energy because of the short distance between
the phone and the user’s head. These RF exposures are limited by FCC safety guidelines
that were developed with the advice of the FDA and other federal health and safety
agencies. When the phone is located at greater distances from the user, the exposure to
RF is drastically reduced due to a person's RF exposure rapidly decreasing with
increasing distance from the source.
The so-called “cordless phones,” which have a base unit connected to the telephone
wiring in a house, typically operate at far lower power levels, thus producing RF
exposures far below the FCC safety limits.
5. What is the FDA doing to find out more about the possible health effects of wireless
phone RF?
The FDA is working with the U.S. National Toxicology Program and with groups of
investigators around the world to ensure that high-priority animal studies are conducted
to address concerns about the effects of exposure to Radio Frequency (RF) energy.
The FDA has been a leading participant in the World Health Organization International
Electro Magnetic Fields (EMF) Project since its inception in 1996. An influential result of
this work has been the development of a detailed agenda of research needs that has
implemented new research programs around the world. The project has also resulted in a
series of public information documents on EMF issues. The FDA and the Cellular
Telecommunications & Internet Association (CTIA) have a formal Cooperative Research
and Development Agreement (CRADA) to conduct research on wireless phone safety.
The FDA provides the scientific oversight, obtaining input from experts in government,
industry, and academic organizations. CTIA-funded research is conducted through
contracts with independent investigators. The initial research will include both laboratory
studies and studies of wireless phone users. The CRADA will also include a broad
assessment of additional research needs in the context of the latest research
developments around the world.
6. What research is needed to decide whether RF exposure from wireless phones poses
a health risk?
A combination of laboratory studies and epidemiological studies of people actually using
wireless phones would provide some of the vital data. Lifetime animal exposure studies
could be completed in a few years. However, very large numbers of animals would be
needed to provide reliable proof of a cancer-promoting effect, if one exists.
Epidemiological studies can provide data that is directly applicable to human
populations, but ten or more years of follow-up research may be needed to provide
answers about certain health effects, such as cancer.
This is due to the interval between exposure time to a cancer-causing agent and the rate
for which tumors develop - if they do. This could take several years into the future. The
interpretation of epidemiological studies is hampered by difficulties in measuring actual
RF exposure during day-to-day use of wireless phones. Many factors affect this
measurement, such as the angle at which the phone is held, or which model of phone is
used.
7. What has the FDA done to measure the Radio Frequency energy coming from
wireless phones?
The Institute of Electrical and Electronic Engineers (IEEE) is developing a technical
standard for measuring the Radio Frequency (RF) energy exposure from wireless phones
and other wireless handsets with the participation and leadership of FDA scientists and
engineers. The standard, “Recommended Practice for Determining the Spatial-Peak
Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications
Devices: Experimental Techniques”, sets forth the first consistent test methodology for
measuring the rate at which RF is deposited in the heads of wireless phone users. The test
method uses a tissue-simulating model of the human head. Standardized SAR test
methodology is expected to greatly improve the consistency of measurements made at
different laboratories on the same phone. SAR is the measurement of the amount of
6. Do not paint your phone.
7. Phone data, including contact information, ringtones, text messages, voice messages,
pictures or videos, etc., may be inadvertently deleted due to careless use, phone repair, or
software upgrades. Please back up your important phone numbers and all other vital
data. Note: Neither the manufacturer nor any person or entity associated therewith is
liable for any damages whatsoever due to loss of any or all data stored on any of your
devices.
8. When using the phone in public places, set the ringtone to vibration so you don't
disturb others.
9. Do not turn your phone on or off while the device is in close proximity to your ear.
10. Use accessories, such as earphones and headsets with caution. Ensure that cables are
tucked away safely and do not touch the antenna.
Caution:
Avoid potential hearing loss.
Prolonged exposure to loud sounds (including music) is the most common cause of
preventable hearing loss. Some scientific research suggests that using portable audio
devices, such as portable music players and cellular telephones, at high volume settings
for long durations may lead to permanent hearing loss. This includes the use of
headphones (including headsets, ear buds and Bluetooth®, or other wireless devices).
Exposure to very loud sound has also been associated in some studies with tinnitus
(ringing in the ear), hypersensitivity to sound, and distorted hearing. The amount of
sound produced by a portable audio device varies depending on the nature of the sound,
the device, the device settings and the headphones. Hence, individual susceptibility to
noise-induced hearing loss and other hearing problems can vary. Please follow these
important guidelines for hearing loss prevention:
1. Set the phone’s volume in a quiet environment and select the lowest volume for which
you can hear clearly.
2. When using headphones, turn the volume down if you cannot hear the people
speaking near you or if the person sitting next to you can hear what you are listening to.
3. Do not turn the volume up to block out noisy surroundings. If you choose to listen to
your portable device in a noisy environment, consider using noise-cancelling headphones
to block out background noise.
4. As the volume increases, less time is required before your hearing could be affected,
so consider limiting your listening time.
5. Avoid using headphones after exposure to extremely loud noises (e.g.: live concerts)
that might cause temporary hearing loss which, in turn, might cause unsafe volume levels
to sound like normal levels.
6. Do not listen at any volume that causes you discomfort. If you experience ringing in
your ears, hear muffled speech or experience any temporary hearing difficulty after
listening to your portable audio device, discontinue use and consult your health care
provider.
You can obtain additional information on this subject from the following sources:
American Academy of Audiology
11730 Plaza American Drive, Suite 300 Reston, VA 20190
Voice: [phone]
Email: [e-mail]
Internet: www.audiology.org
National Institute on Deafness and Other Communication Disorders
National Institutes of Health
31 Center Drive, MSC 2320 Bethesda, MD USA 20892-2320
Voice: [phone]
Email: [e-mail]
Internet: http://www.nidcd.nih.gov/health/hearing
National Institute for Occupational Safety and Health
Hubert H. Humphrey Bldg. 200 Independence Ave., SW Washington, DC 20201
Voice: 1-800-35-NIOSH (1-800-232-4636)
Internet: http://www.cdc.gov/niosh/topics/noise/default.html
Safety Information
Please read and observe the following information for safe and proper use of your phone
and to prevent damage. Also, keep the user guide in an accessible place after reading it
for ease in locating it for future reference.
Violation of the instructions may cause minor or serious damage to the product.
1. Do not disassemble, open, crush, bend or deform, puncture or shred your equipment.
2. Do not modify or remanufacture your equipment. Do not attempt to insert foreign
objects into the battery. Do not immerse your equipment in water or other liquids, or
expose it to water or other liquids, fire, explosions or other hazards.
3. Do not short-circuit the battery or allow metallic conductive objects to contact the
battery terminals.
4. Avoid dropping the phone. If the phone is dropped on a hard surface or elsewhere,
take it to a service center for inspection if damage is suspected.
Charger and Adapter Safety
1. The charger and adapter are intended for indoor use only.
2. Insert the battery pack charger vertically into the wall power socket.
3. Only use the approved battery charger so as to avoid serious damage to your phone.
4. When traveling abroad, only use the approved battery pack charger along with the
correct phone adapter.
Battery Information: Care and Proper Disposal
1. Please dispose of your battery properly or take it to your local wireless carrier for
recycling.
2. The battery doesn’t need to be empty before recharging, and replace the battery
when it no longer provides acceptable performance. Note: The battery can be
recharged several hundred times and it does not need to be empty in order to recharge.
3. Use only manufacturer-approved chargers specific to your phone model as they are
designed to maximize battery life.
4. Do not disassemble or short-circuit the battery.
5. Keep the battery’s metal contacts clean.
6. Recharge the battery after long periods of non-use to maximize battery life. Note:
Battery life will vary due to usage patterns and environmental conditions.
7. Use of extended backlighting, Browser, and data connectivity kits affect battery life as
well as talk/standby times.
8. The self-protection function of the battery cuts the power of the phone when its
operation is in an abnormal state. In this case, remove the battery from the phone,
reinstall it, and turn the phone on.
Explosion, Shock, and Fire Hazards
1. Do not put your phone in a place that is subject to excessive dust, and always keep
the minimum required distance between the power cord and heat sources.
2. Unplug the power cord prior to cleaning your phone, and clean the power plug pin
when necessary.
3. When using the power plug, ensure that it’s firmly connected.
4. Placing the phone in a pocket or bag without covering the phone receptacle (power
plug pin), metallic articles (e.g.: coins, paperclips, pens) may short-circuit the phone.
Always cover the receptacle when not in use.
5. Metallic articles that come into contact with the phone may short-circuit the + and –
battery terminals (metal strips) which may result in battery damage, or even an
explosion.
General Notice
1. Using a damaged battery or placing a battery in your mouth may cause serious injury.
2. Placing items containing magnetic strip components (e.g.: credit cards, phone cards,
bank books, subway tickets) near your phone may damage the data stored in the
magnetic strips.
3. Talking on the phone for long periods of time may reduce call quality due to heat
generation.
4. Do not use the phone if the antenna is damaged as it may cause a slight contact
burn. Please communicate with the Authorized Service Center to replace the damaged
antenna.
5. Do not immerse your phone in water. If this happens, immediately turn the phone
OFF and remove the battery. If the phone does not work, take it to the Authorized
Service Center.
Antenna Care
Use only the supplied or approved replacement antenna. Unauthorized antennas,
modifications, or attachments could damage the phone and may violate FCC regulations.
Phone Operation
NORMAL POSITION: Hold the phone as you would any other telephone with the antenna
pointed up and over your shoulder.
Tips on Efficient Operation
For your phone to operate most efficiently, do not touch the antenna unnecessarily when
operating the phone. Contact with the antenna affects call quality and may cause the
phone to operate at a higher power level than otherwise needed, thus reducing battery
life.
Driving
Always observe the laws and regulations regarding wireless phone usages while driving.
Where cell phone use is permitted while driving, you MUST observe the following:
1. Give full attention to driving -- driving safely is your first responsibility;
2. Use hands-free operation, if available;
3. Pull off the road and park before making or answering a call if driving conditions or
the law requires that you do so.
Pacemakers
The Health Industry Manufacturers Association recommends that a minimum separation
of six (6) inches be maintained between a handheld wireless phone and a pacemaker to
avoid potential interference with the pacemaker. These recommendations are consistent
with the independent research by and recommendations of Wireless Technology
Research.
Persons with pacemakers:
1. Should ALWAYS keep the phone more than six (6) inches from their pacemaker when
the phone is turned ON;
2. Should not carry the phone in a breast pocket;
3. Should use the ear opposite the pacemaker to minimize the potential for interference;
4. Should turn the phone OFF immediately if there is any reason to suspect that
interference is occurring.
Electronic Devices
Most modern electronic equipment is shielded from RF signals but some equipment or
devices might not be.
Hearing Aids
Some digital wireless phones may interfere with hearing aids. In the event of such
interference, you please consult your service provider, or call customer service regarding
alternatives.
Other Medical Devices
If you use other personal medical devices, consult the device manufacturer to determine
if it is adequately shielded from external RF energy, or your health care provider may be
able to advice about any harmful device interactions.
Vehicles
RF signals may affect improperly installed or inadequately shielded electronic systems in
motor vehicles. Be certain to contact the manufacturer or representative regarding this
as well as manufacturer of any additional vehicle equipment.
Posted Facilities
Turn your phone OFF in any facility where posted notices so require.
For Vehicles Equipped with an Air Bag
DO NOT place objects, including installed or portable wireless equipment, in the area
over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is
improperly installed and the air bag inflates, serious injury could result since air bags
inflate with great force.
FDA Consumer Update
The U.S. Food and Drug Administration’s (FDA) Center for Devices and Radiological
Health Consumer Update on Mobile Phones:
1. What is the FDA's role concerning the safety of wireless phones?
Under the law, the FDA does not review the safety of radiation-emitting consumer
products such as wireless phones before they can be sold, as it does with new drugs or
medical devices. However, the agency has authority to take action if wireless phones are
shown to emit Radio Frequency (RF) energy at a level that is hazardous to the user. In
such a case, the FDA could require the manufacturers of wireless phones to notify users
of the health hazard and to repair, replace, or recall the phones so that the hazard no
longer exists.
Although the existing scientific data does not justify FDA regulatory actions, the FDA has
urged the wireless phone industry to take a number of steps, including the following:
1. Support current and future research regarding possible biological effects of the type
of RF emitted by wireless phones;
2. Design wireless phones in a way that minimizes any RF exposure to the user that is
not necessary for device function; and
3. Cooperate in providing users of wireless phones with complete and accurate
information regarding possible effects of wireless phone use on human health and safety.
The FDA belongs to an interagency working group of the federal agencies that have
responsibility for different aspects of RF safety to ensure coordinated efforts at the
federal level. The following agencies belong to this working group:
1. National Institute for Occupational Safety and Health
2. Environmental Protection Agency
3. Occupational Safety and Health Administration
4. National Telecommunications and Information Administration
The National Institutes of Health participates in some interagency working group
activities as well. The FDA shares regulatory responsibilities for wireless phones with the
Federal Communications Commission (FCC). All phones that are sold in the United States
must comply with FCC safety guidelines that act to limit RF exposure. The FCC relies on
the FDA and other health agencies for safety questions about wireless phones.
The FCC also regulates the base stations that the wireless phone networks rely upon.
While these base stations operate at higher power than do the wireless phones
themselves, the RF exposures that people get from these base stations are typically
thousands of times lower than those they can get from wireless phones. Base stations are
thus not the subject of the safety questions discussed in this document.
2. Do wireless phones pose a health hazard?
Current scientific evidence does not show that any health problems are associated with
using wireless phones. There is no proof, however, that wireless phones are absolutely
safe. Wireless phones emit low levels of Radio Frequency (RF) energy while operating
microwave ranges (which also emit very low levels of RF when they are in standby mode).
While high levels of RF can produce health effects (by heating tissue), exposure to
low-level RF that does not produce heating effects results in no known adverse health
effects. Many studies of low-level RF exposures have not uncovered any biological effects.
Although some studies have suggested that some biological effects may occur, such
findings have not been confirmed by additional research. In some cases, other researchers
have had difficulty in reproducing those studies, and/or determining the reasons for
inconsistent results.
3. What are the results of the research done already?
The research conducted thus far has produced conflicting results, and many studies have
suffered from flaws in their research methods. Animal experiments investigating the
effects of Radio Frequency (RF) energy exposures characteristic of wireless phones have
yielded conflicting results that often cannot be repeated in other laboratories. A few
animal studies, however, have suggested that low levels of RF could accelerate the
development of cancer in laboratory animals. However, many of the studies that showed
increased tumor development used animals that had been genetically engineered or
treated with cancer-causing chemicals so as to be pre-disposed to develop cancer in the
absence of RF exposure. Other studies exposed the animals to RF for up to 22 hours per
day. These conditions are not similar to the conditions under which people use wireless
phones, so it is largely unknown what the results of such studies mean for human health
and safety. Three large epidemiology studies have been published since December 2000.
These studies investigated possible associations between the use of wireless phones and
primary brain cancer (glioma, meningioma, acoustic neuroma, other brain tumors, and
12. Where can I find additional information?
For additional information, please refer to the following resources: FDA web page on
wireless phones (http://www.fda.gov), under “C” in the subject index, select Cell Phones >
Current Research Results. Federal Communications Commission (FCC) RF Safety
Program (http://www.fcc.gov/cgb/cellular.html) International Commission on Nonionizing
Radiation Protection (http://www.icnirp.de) World Health Organization (WHO)
International EMF Project (http://www.who.int/emf) Health Protection Agency
(http://www.hpa.org.uk/)
Consumer Information on SAR
This Model Phone Meets the Government’s Requirements for Exposure to Radio Waves.
Your wireless phone is a radio transmitter and receiver. It is designed and manufactured
not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the
Federal Communications Commission (FCC) of the U.S. Government. These FCC
exposure limits are derived from the recommendations of two expert organizations, the
National Council on Radiation Protection and Measurement (NCRP) and the Institute of
Electrical and Electronics Engineers (IEEE). In both cases, the recommendations were
developed by scientific and engineering experts drawn from industry, government, and
academia after extensive reviews of the scientific literature related to the biological
effects of RF energy. The exposure limit for wireless mobile phones employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The SAR is a measure of
the rate of absorption of RF energy by the human body expressed in units of watts per
kilogram (W/kg). The FCC requires wireless phones to comply with a safety limit of 1.6
watts per kilogram (1.6 W/kg). The FCC exposure limit incorporates a substantial margin
of safety to give additional protection to the public and to account for any variations in
measurements. Tests for SAR are conducted using standard operating positions specified
by the FCC with the phone transmitting at its highest certified power level in all tested
frequency bands. Although SAR is determined at the highest certified power level, the
actual SAR level of the phone while operating can be well below the maximum value.
Because the phone is designed to operate at multiple power levels to use only the power
required to reach the network, generally, the closer you are to a wireless base station
antenna, the lower the power output. Before a phone model is available for sale to the
public, it must be tested and certified to the FCC that it does not exceed the limit
established by the government adopted requirement for safe exposure. The tests are
performed in positions and locations (e.g., at the ear and worn on the body) as required
by the FCC for each model. This device was tested for typical body-worn operations with
the back of the phone kept 0.59 inches (1.5 cm) between the user’s body and the back of
the phone. To comply with FCC RF exposure requirements, a minimum separation
distance of 0.59 inches (1.5 cm) must be maintained between the user's body and the
back of the phone. Third-party belt clips, holsters, and similar accessories containing
metallic components should not be used.
Body-worn accessories that cannot maintain 0.59 inches (1.5 cm) separation distance
between the user's body and the back of the phone, and have not been tested for typical
body-worn operations may not comply with FCC RF exposure limits and should be
avoided.
The FCC has granted an Equipment Authorization for this model phone with all reported
SAR levels evaluated as in compliance with the FCC RF emission guidelines.
The highest SAR value for this model phone when tested for use at the ear is 1.07
W/kg and when worn on the body, as described in this user’s manual, is 1.39 W/kg.
While there may be differences between SAR levels of various phones and at various
positions, they all meet the government requirement for safe exposure.
SAR information on this model phone is on file with the FCC and can be found under the
Display Grant section of http://www.fcc.gov/oet/ea/fccid/ after searching on FCC ID:
R38YLCP3648A.
To find information that pertains to a particular model phone, this site uses the phone
FCC ID number which is usually printed somewhere on the case of the phone. Sometimes
it may be necessary to remove the battery pack to find the number. Once you have the
FCC ID number for your phone, follow the instructions on the website and it should
provide values for typical or maximum SAR for that phone.
Additional information on Specific Absorption Rates (SAR) can be found on the Cellular
Telecommunications Industry Association (CTIA) website at http://www.ctia.org/
In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6
watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a
substantial margin of safety to give additional protection for the public and to account
for any variations in measurements.
energy absorbed in tissue, either by the whole body or a small part of the body. It is
measured in watts/kg (or mill-watts/g) of matter. This measurement is used to determine
whether a wireless phone complies with safety guidelines.
8. How can I find out how much Radio Frequency energy exposure I can get by using
my wireless phone?
All phones sold in the United States must comply with Federal Communications
Commission (FCC) guidelines that limit Radio Frequency (RF) energy exposures. The FCC
established these guidelines in consultation with the FDA and the other federal health
and safety agencies. The FCC limit for RF exposure from wireless phones is set at a
Specific Absorption Rate (SAR) of 1.6 watts per kilogram (1.6W/kg). The FCC limit is
consistent with the safety standards developed by the Institute of Electrical and
Electronic Engineering (IEEE) and the National Council on Radiation Protection and
Measurement. The exposure limit takes into consideration the body’s ability to remove
heat from the tissues that absorb energy from the wireless phone and is set well below
levels known to have effects. Manufacturers of wireless phones must report the RF
exposure level for each model of phone to the FCC.
The FCC website (http://www.fcc.gov/cgb/cellular.html) gives directions for locating the
FCC identification number on your phone, so you can find your phone’s RF exposure level
in the online listing.
9. What about children using wireless phones?
The scientific evidence does not show a danger to users of wireless phones, including
children and teenagers. If you want to take steps to lower exposure to Radio Frequency
(RF) energy, the measures described above would apply to children and teenagers using
wireless phones. Reducing the time of wireless phone use and increasing the distance
between the user and the RF source will reduce RF exposure.
Some groups sponsored by other national governments have advised that children be
discouraged from using wireless phones at all. For example, the government in the United
Kingdom distributed leaflets containing such a recommendation in December 2000. They
noted that no evidence exists that using a wireless phone causes brain tumors or other ill
effects. Their recommendation to limit wireless phone use by children was strictly
precautionary; it was not based on scientific evidence that any health hazard exists.
10. What steps can I take to reduce my exposure to Radio Frequency energy from my
wireless phone?
If there is a risk from these products- and at this point we do not know that there is - it is
probably very small. But if you are concerned about avoiding even potential risks, you can
take a few simple steps to minimize your exposure to Radio Frequency (RF) energy. Since
time is a key factor in how much exposure a person receives, reducing the amount of time
spent using a wireless phone will reduce RF exposure. If you must conduct extended
conversations by wireless phone on a daily basis, consider placing more distance between
your body and the source of the RF, since the exposure level drops off dramatically with
distance. For example, you could use a headset and carry the wireless phone away from
your body or use a wireless phone connected to a remote antenna. Again, the scientific
data does not demonstrate that wireless phones are harmful. But if you are concerned
about the RF exposure from these products, you can use measures like those described
above to reduce your RF exposure from wireless phone use.
11. What about wireless phone interference with medical equipment?
Radio Frequency (RF) energy from wireless phones can interact with some electronic
devices. For this reason, the FDA helped develop a detailed test method to measure
Electro Magnetic Interference (EMI) of implanted cardiac pacemakers and defibrillators
from wireless telephones. This test method is now part of a standard sponsored by the
Association for the Advancement of Medical Instrumentation (AAMI). The final draft, a
joint effort by the FDA, medical device manufacturers, and many other groups, was
completed in late 2000. This standard will allow manufacturers to ensure that cardiac
pacemakers and defibrillators are safe from wireless phone EMI. The FDA has tested
hearing aids for interference from handheld wireless phones and helped develop a
voluntary standard sponsored by the Institute of Electrical and Electronic Engineers
(IEEE). This standard specifies test methods and performance requirements for hearing
aids and wireless phones so that no interference occurs when a person uses a
“compatible” phone and a “compatible” hearing aid simultaneously. This standard was
approved by the IEEE in 2000. The FDA continues to monitor the use of wireless phones
for possible interactions with other medical devices. Should harmful interference be found
to occur, the FDA will conduct testing to assess the interference and work to resolve the
problem.
THIS LIMITED WARRANTY SETS OUT THE FULL EXTENT OF COOLPAD'S
RESPONSIBILITIES, AND THE EXCLUSIVE REMEDY REGARDING THE PRODUCTS.
ALL DISPUTES WITH COOLPAD ARISING IN ANY WAY FROM THIS LIMITED WARRANTY
OR THE SALE, CONDITION OR PERFORMANCE OF THE PRODUCTS SHALL BE
RESOLVED EXCLUSIVELY BY ANY COURT WITH COMPETENT JURISDICTION. Any such
dispute shall not be combined or consolidated with a dispute involving any other
person's or entity's Product or claim, and specifically, without limitation of the foregoing,
shall not under any circumstances proceed as part of a class action. The laws of the State
of California, without reference to its choice of laws principles, shall govern the
interpretation of the Limited Warranty and all disputes arising out of the products or
services.
This settlement of disputes also applies to claims against COOLPAD'S employees,
contractors, agents, and/or other representatives, as well as any of all of its affiliated
entities, regardless of place of incorporation, if any such claim arises from the Product's
sale, condition or performance. Notwithstanding the foregoing, neither this warranty nor
provision of any Product shall, in and of itself, provide for in persona jurisdiction over any
of COOLPAD's employees, contractors, agents, and/or other representatives, or over its
affiliated entities.
Severability
If any portion of this Limited Warranty is held to be illegal or unenforceable, such partial
illegality or unenforceability shall not affect the enforceability of the remainder of the
Limited Warranty.
Coolpad Technologies, Inc.
6175 Main St., Suite 290
Frisco, TX 75034
Customer Service: 1-877-606-5753
Standard Limited Warranty
(This standard Limited Warranty supersedes and replaces for all purposes the Standard
Limited Warranty that appears in the enclosed documentation, if any)
COOLPAD TECHNOLOGIES, INC.("COOLPAD") warrants that COOLPAD's handsets and
accessories enclosed herein ("Products") are free from defects in material and
workmanship under normal use and service for the period commencing upon the date of
purchase by the first consumer purchaser and continuing for the following specified
period of time after that date:
Phone 12 months
Battery and Charger 6 months
Other Accessories(If included in the box set) 3 months
This Limited Warranty is conditioned upon proper use of the Products. This Limited
Warranty does not cover: (a) defects or damage resulting from accident, misuse,
abnormal use, abnormal conditions, improper storage, exposure to liquid, moisture,
dampness, sand or dirt, neglect, or unusual physical, electrical or electromechanical
stress; (b) scratches, dents and cosmetic damage, unless caused by COOLPAD; (c)
defects or damage resulting from excessive force or use of a metallic object when
pressing on a touch screen; (d) equipment from which the serial number and/or the
enhancement data code have been removed, defaced, damaged, altered, made illegible,
and/or otherwise tampered with; (e) ordinary wear and tear; (f) defects or damage
resulting from the use of Product in conjunction or connection with accessories,
products, or ancillary/peripheral equipment not furnished or approved by COOLPAD; (g)
defects or damage resulting from improper testing, operation, maintenance, installation,
service, or adjustment not furnished or approved by COOLPAD; (h) defects or damage
resulting from external causes such as collision with an object, fire, flooding, dirt,
windstorm, lightning, earthquake, exposure to weather conditions, theft, blown fuse, or
improper use of any electrical source; (i) defects or damage resulting from cellular signal
reception or transmission, viruses and/or other software problems introduced into the
Product; or (j) Product used or purchased outside the United States. This Limited
Warranty covers batteries only if battery capacity falls below 80% of rated capacity or
the battery leaks, and this Limited Warranty does not cover any battery if: (i) the battery
has been charged by a battery charger not specified or approved by COOLPAD for
charging the battery; (ii) any of the seals on the battery are broken or show evidence of
tampering; or (iii) the battery has been used in equipment other than the COOLPAD
phone for which it is specified.
During the applicable warranty period, provided the Product subject to the warranty
claim is returned in accordance with the terms of this Limited Warranty, COOLPAD will
repair or replace such Product, at COOLPAD'S sole option, without charge. COOLPAD
may, at COOLPAD's sole option, use rebuilt, reconditioned, or new parts or components
when repairing any Product, or may replace the Product with a rebuilt, reconditioned or
new Product. All other repaired/replaced Products will be warranted for a period equal to
the remainder of the original Limited Warranty on the original Product or for ninety (90)
days, whichever is longer. All replaced Products, parts, components, boards and
equipment shall become the property of COOLPAD. Except to any extent expressly
allowed by applicable law, transfer or assignment of this Limited Warranty is prohibited.
To obtain service under this Limited Warranty, you must return the Product to an
authorized phone service facility in an adequate container for shipping, accompanied by
the sales receipt or comparable proof of sale showing the original date of purchase, the
serial number of the Product and the seller's name and address. Replacement parts and
related service manual and diagnostic tools are available in our authorized service center
within ninety (90) days after launch of the Product. Replacement parts and/or services
are available for three years after the end of production of the product. To obtain
assistance on where to deliver the Product, please call COOLPAD Customer Care at
1-877-606-5753. If COOLPAD determines that any Product is not covered by this Limited
Warranty, you must pay all parts, shipping, and labor charges for the repair or return of
such Product.
You should keep a separate backup copy of any contents of the Product before
delivering the Product to COOLPAD for warranty service, as some or all of the contents
may be deleted or reformatted during the course of warranty service.
FCC Hearing-Aid Compatibility (HAC) Regulations for Wireless Devices
On July 10, 2003, the U.S. Federal Communications Commission (FCC) Report and Order
in WT Docket 01- 309 modified the exception of wireless phones under the Hearing Aid
Compatibility Act of 1988 (HAC Act) to require digital wireless phones be compatible
with hearing-aids. The intent of the HAC Act is to ensure reasonable access to
telecommunications services for persons with hearing disabilities. While some wireless
phones are used near some hearing devices (hearing aids and cochlear implants), users
may detect a buzzing, humming, or whining noise. Some hearing devices are more
immune than others to this interference noise, and phones also vary in the amount of
interference they generate. The wireless telephone industry has developed a rating
system for wireless phones, to assist hearing device users to find phones that may be
compatible with their hearing devices. Not all phones have been rated. Phones that are
rated have the rating on their box or a label located on the box. The ratings are not
guarantees. Results will vary depending on the user's hearing device and hearing loss. If
your hearing device happens to be vulnerable to interference, you may not be able to use
a rated phone successfully. Trying out the phone with your hearing device is the best way
to evaluate this.
M-Ratings: Phones rated M3 or M4 meet FCC requirements and are likely to generate less
interference to hearing devices than phones that are not labeled. M4 is the better/higher
of the two ratings.
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to generate less
interference to hearing devices than phones that are not labeled. T4 is the better/ higher
of the two ratings.
Hearing devices may also be rated. Your hearing device manufacturer or hearing health
professional may help you find this rating. Higher ratings mean that the hearing device is
relatively immune to interference noise. The hearing aid and wireless phone rating values
are then added together. A sum of 5 is considered acceptable for normal use. A sum of 6
is considered for best use.
In the example illustrated above, if a hearing aid meets the M2 level rating and the
wireless phone meets the M3 level rating, the sum of the two values equal M5. This
should provide the hearing-aid user with “normal usage” while using their hearing aid
with the particular wireless phone. “Normal usage” in this context is defined as a signal
quality that’s acceptable for normal operation.
The M mark is intended to be synonymous with the U mark. The T mark is intended to be
synonymous with the UT mark. The M and T marks are recommended by the Alliance for
Telecommunications Industries Solutions (ATIS). The U and UT marks are referenced in
Section 20.19 of the FCC Rules. The HAC rating and measurement procedure are
described in the American National Standards Institute (ANSI) C63.19 standard.
When you're talking on a cell phone, it's recommended that you turn the BT (Bluetooth)
mode off for HAC.
For information about hearing aids and digital wireless phones
Wireless Phones and Hearing Aid Accessibility
http://www.accesswireless.org/Home.aspx
FCC Hearing Aid Compatibility and Volume Control
http://www.fcc.gov/cgb/consumerfacts/hac_wireless.htm
IC
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Note: Some content and services accessible through this device belong to third parties
and are protected by copyright, patent, trademark and/or other intellectual property
laws. Such content and services are provided solely for your personal noncommercial
use. You may not use any content or services in a manner that has not been authorized
by the content owner or service provider. Without limiting the foregoing, unless expressly
authorized by the applicable content owner or service provider, you may not modify,
copy, republish, upload, post, transmit, translate, sell, create derivative works, exploit, or
distribute in any manner or medium any content or services displayed through this
device.