Quick Start Guide
INTRODUC TION Breeze is a flying camera that is designed to take aerial photos and videos of you. It is small, easy to fly both indoors and outdoors, and is controlled by your smart phone or tablet computer. The application (Breeze Cam) features five custom automatic flight modes that make positioning Breeze very easy. Once you’re done flying, you can download photos and videos to your device and share them to your favorite social networks directly from the app.
SPECIFICATIONS Aircraft Dimensions (without propeller protectors): 196x196x65 mm Dimensions (with propeller protectors): 327x327x65 mm Diagonal Wheelbase: 240mm Takeoff Weight: 385g Propeller Protector: Quick-Release Propeller Protector. Battery: 3-Cell 11.1V 1150mAh 12.
Charger Model: BC24803015 Output: 12.6V DC,1.5A PREPARATIONS 1. CHARGING THE BATTERY (~45min) charger LED codes Standby Charging Abnormal Charging Balance Charging Fully Charged Battery Warnings: To charge the flight battery, you must use only the included charger. Do not over-discharge the LiPo battery. If at any time the LiPo battery begins to balloon or swell,discontinue charging or discharging immediately. Always terminate all processes if the battery, charger or power supply malfunction.
NOTICE: FAMILIARIZE YOURSELF WITH EACH TASK MODE BY READING THE TUTORIALS ON THE BREEZE CAM APP BEFORE OPERATING BREEZE. 3. UNFOLDING THE LANDING GEAR Unfold the four landing gears as shown in the below illustration. 4. INSTALLING THE PROPELLER PROTECTORS Install the four propeller protectors to the corresponding positions as shown in the illustration below. To remove the propeller protectors, unlock them from the engine arm from one side to another.
5. REMOVING THE LENS COVER 6. INSTALLING THE FLIGHT BATTERY Slide in the fully charged battery until it locks. Remove the battery by pressing the locking tab and sliding the battery to the rear of Breeze . 7. POWERING ON/OFF BREEZE POWER ON: To start your Breeze , press and hold the power button at the rear of Breeze. When Breeze is on, the LED indicator will blink blue-red-green four times and emit a sound. When the LED indicator blinks blue rapidly, Breeze will enter “bind” mode.
POWER OFF: Press and hold the power button until the LED glows solid red. After successfully switching off, it will emit a “power off” sound after letting go of the power button. 8. BINDING BREEZE WITH YOUR SMART DEVICE Power on your Breeze on a flat and stable surface and wait for it to complete initialization. When the LED indicator blinks blue rapidly, Breeze has entered the “Wi-Fi” bind mode.
Nor th 1.5m ( 5ft ) Tap [ ] and select Drone Settings, and then swipe the screen to “Compass Calibration”. Follow the on-screen animations to complete the calibration. The LED indicator blinks white or yellow during the whole compass calibration process, when you complete the process, the LED will blink green and Breeze will emit an audible sound. Recalibrate the compass if the LED blinks red as this means calibration has failed.
12. UNDERSTANDING THE FLIGHT MODES Tap the [ ] icon to enter the TASK page and there are five flight modes for you to select with: TAS KS 0 100% ? SELFIE PILOT ORBIT JOURNEY FOLLOW ME Before GPS is ready,only Pilot mode can be used. 13. PLACEMENT BEFORE TAKING OFF R Switched On Pilot location SAFE DISTANCE 4m(13ft) First, ensure the area around the Breeze is cleared for flight, then tap [ TAKE OFF ] to start the motors and lift Breeze off the ground.
FLIGHT LOG Support ], You will find FLIGHT Tap [ ] and select [ LOG icon on the right corner of the “Support” interface. The Flight Log is designed to record your total flights, including flight time, flight date and flight location. You may email the flight log info to Yuneec Customer Support when needed.
GENERAL WARNINGS 1. Breeze is not suitable for children under 14 years of age. 2. Breeze is designed for leisure purposes. The pilot must always maintain direct visual contact with Breeze and monitor its trajectory. Breeze must be used in accordance with the civil aviation regulations in your country. 3. Always operate your Breeze in open areas that are free from people, vehicles and other obstructions.
DISCLAIMER Yuneec Electric Aviation cannot be held liable for any damage, injury or for use of the product in violation with legal regulations, especially in the following circumstances: Damage and / or injury as well violation of legal regulations resulting from a failure to comply with the operating instructions or the instructions at www.yuneec.com, product information, user manual and other legally binding information.
Damage and/or injury as well as violation of legal regulations caused by operating the model in a magnetic field (e.g. high voltage lines, electricity/transformer stations, radio towers, mobile phone masts etc.), a strong wireless signal environment,no-fly zones, poor visibility and in the event of vision impairments or other impacts on the pilot which are left unchecked etc.
FCC STATEMENT This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IC RADIATION EXPOSURE STATEMENT FOR CANADA This device complies with Industry Canada licence-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
COLLEC TION AND PROCESSING OF DATA Yuneec may collect navigation information such as GPS data to help improve our products. We may also collect Depth Map information and Infrared Image information from your drone delivered to our service center for repair and maintenance service or any other service. We may also collect other information such as device information, server log information, etc.
CUSTOMER SERVICE Manufacturer Yuneec International (China) Co., Ltd. Production Address: East Zhengwei Road No.388, Jinxi Town, Kunshan City, Jiangsu Province Distributor US: Yuneec USA Inc. Address: 5555 Ontario Mills Parkway, Ontario, CA91764, USA Tel: +1 855 284 8888 EU: Yuneec Europe GmbH Address: Niklaus–Otto-Strasse 4, 24568 Kaltenkirchen, Germany. Tel: +49 4191 932620 CN: Youyu (Shanghai) Digital Technology Co.,Ltd.